Zavus Buyck Displays Counter display Installation Guide
- August 31, 2024
- Zavus
Table of Contents
Buyck Displays Counter display
“`html
Specifications:
- Material: Acrylic
- Mounting Type: Wall-mounted
- Hardware Included: Standoff Assembly, Drywall Anchor, Screw #8
x 1
Product Usage Instructions:
Installation:
These instructions are for typical drywall and wood-stud wall
construction. For other substrates like brick or concrete,
different fasteners will be needed. The installer must select
appropriate fasteners and tools for the application.
Required Tools:
- Tape Measure
- Level
- Pencil or Marking Tool
- Drill (3.0mm)
- Screwdriver
Steps:
-
Wear proper Personal Protective Equipment (PPE) like safety
glasses and a dust mask. -
Position the display on the wall using the tools and hardware
provided. -
Use the pencil to mark drilling points.
-
Drill holes at the marked points using a 3.0mm drill bit.
-
Insert Drywall Anchors into the holes.
-
Attach Standoff Assemblies to the wall using screws #8 x
-
Place the display onto the Standoff Assemblies for
installation.
FAQ:
Q: Can this acrylic display be used outdoors?
A: This display is designed for indoor use. Exposure to outdoor
elements may cause damage to the acrylic material over time.
Q: What is the weight capacity of this display?
A: The weight capacity depends on the wall construction and
fasteners used. It is recommended to consult with a professional if
planning to display heavy items.
“`
Installation Instructions Acrylic Display
These instructions are for are for typical drywall and wood-stud wall
construction. It will be necessary to source other fasteners if mounting to a
different substrate such as brick, concrete, etc. It is up to the installer to
determine appropriate fasteners for the application. Additional tools may also
be required.
Always be sure to wear proper Personal-Protective-Equipment (PPE), such as
safety glasses, dust mask etc.
Hardware (Supplied)
Standoff Assembly (4)
Drywall Anchor (4)
Screw, #8 x 1″ (4)
1
Tools (Not Supplied)
Tape Measure
Level
Pencil/Marking-tool
Drill
Drill bit, Ø7/32″ (5.5mm) Drill bit, Ø7/64″ #2 Cross head bit or
(3.0mm)
screwdriver
Step 1 Plan location and Hardware · Determine alternate hardware if needed. · It is preferable to leave protective film on the display until the last step. · Determine location; vertical position is typically set at eye-level. · For increased strength, align the mounting holes on one side with a stud. o In the example below the left side fastener will be secured to a stud and the right side with wall anchors. Note that a longer #8 screw will be required for fastening to a stud.
2
Step 2 Mark Holes · Once the display has been located, use a level to ensure
correct orientation and mark holes
Step 3 Drill holes · For anchor holes use drill bit Ø7/32″ (5.5mm). Holes must
pierce completely through drywall. · For holes into a stud, use drill bit
Ø7/64″ (3.0mm). Holes should be deep enough to accommodate the longer screw.
3
Step 4 Install wall anchors · Gently tap wall anchors into holes ensuring the
top is flush with the outer drywall surface
Step 5 Fasten standoffs to wall · Using the drill or screwdriver install
standoff base with screws. · Be sure to use longer screw for stud location and
shorter screws for anchor locations. · Do not over tighten!
4
Step 6 Hang display · Be sure to remove any protective film from the display,
if not do so already. · Install the display on standoff bases as shown below.
Be sure to sandwich the display with plastic washers provided. · The standoff
tops are simply hand tightened
The display is now ready for medal installation.
5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>