FEIT ELECTRIC S13CWPK/MM/BZ Outdoor Commercial Wall Light User Guide

FEIT ELECTRIC S13CWPK/MM/BZ Outdoor Commercial Wall Light

Product Information

Specifications:

• Model: S13CWPK/MM/BZ
• Type: Outdoor Commercial Wall Light
• Quantity: 1
• Motion Sensor Coverage: 180 degrees, up to 60 ft detection range
• Brightness Levels: 100% at startup, drops to 30% after warmup, returns to 100% with motion detection
• Color Temperature (CCT): 4000K – 6500K

Product Usage Instructions

Installation:

1. Read the manual carefully before installation.
2. Identify and organize the provided parts: AA, BB, CC, DD, EE, FF, and GG.
3. Mount the wall light using the provided screws and anchors.
4. Connect the supply line and neutral wires using twist-on wire connectors.
5. Connect the LED driver to the power supply and grounding.
6. Optional: Use the Dust-To-Dawn Sensor Cover for continuous lighting control.

Operation:

• Upon powering up, there will be a 10-second warmup period before the brightness drops to 30%.
• The light will return to 100% brightness when motion is detected.
• The motion sensor has a 180-degree coverage with a maximum range of 60 ft.

FAQ:

Problem: The light will not illuminate.

• Possible Cause: Faulty wire connection.
• Solution: Check the wiring and consult a qualified electrician if needed.

Problem: The security light cycles ON and OFF continuously.

• Possible Cause: Dusk-to-Dawn sensor sensing reflected light.
• Solution: Remove reflective materials near the wall pack or relocate it to avoid reflected light.
• Problem: Light will not dim to 30% in D2D mode.
• Solution: Position the switch to the MOT mode for proper dimming.

THANKYOU
We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this LED yard light fixture. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric!

DUSK TO DAWN OPERATION:

• The light will turn on at dusk and remain on through the night until dawn.
• The light will remain off throughout the day, until dusk.
• NOTICE: To make sure this function works properly, always keep the wall switch in the “ON” position (including daytime).
• NOTICE: A sensor cover (GG) is provided which can be used to block out light and bypass the sensor. This will keep the light continuously on and the fixture can be controlled to tum on/off through the wall switch or a master photocell.

Safety Information

• For your safety, always remember to:
• Turn off the power SUP.Ply at the fuse or circuit breaker box before you install the fixture.
• Ground the mixture to avoid potential electric shock and to ensure reliable starting.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber-soled shoes and work on a sturdy wooden ladder.
• Account for small parts and destroy packing material, as these may be hazardous to children.
• This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed under local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
• Account for small parts and destroy packing material, as these may be hazardous to children.

NOTICE:

• All electrical connections must be per local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
• Remove the fixture and the mountina package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

Product Specifications:

• 120/277 VAC, 50/60Hz, 125W max
• Dimmable with 0-10V dimmer only
• Suitable for wet locations
• WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly.
• CAUTION: Turn off the main power at the circuit breaker before installing the fixture, to prevent possible shock.
• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING:
RISK OF CUTS. Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.

• Supplier’s Declaration of Conformity:
  47 CFR § 2.1077 Compliance Information

• Responsible Party:

  • Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA
  • www.feit.com

• Unique Identifier:
  S13CWPK/MM/BZ

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference (that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the e11uipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radionv technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment [ CAN ICES-005 (B)

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Care and Maintenance

Periodically clean the texture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

ISED STATEMENT

This device complies with lndusti:y Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference 1hat may cause undesired operation of the device.

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from the date of purchase. If the Product fails within the warranty period, please contact Feit Electric at info@feit.com visit feit.com/contact- us, or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE nEMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPUED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion IT) may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | 800-543-3348 | FAX 562-908-6360 | www.feit.com.

Pre-Installation

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)

HARDWARE INCLUDED

Wall Mount Installation

1. Turning Off the Power
   Turn the power OFF at the wall switch, fusebox or circuit breaker.

2. Remove the Front Cover

   • Open the Wall Light (AA) by unscrewing the Front Cover Screws (BB) using a phillips screwdriver (not provided).
   • Remove the Front Cover from the Back Plate by disconnecting the quick-connect wires and sliding the Front Cover in an upward direction.

3. Prep the Back Plate
   Drill 4 holes from the outside surface on the Back Plate using a 1/4 in. drill bit as indicated. Select the desired conduit location and remove the appropriate 1/2 inch plug (II).

4. Affix Back Plate to Wall

   • Using the Back Plate as a guide, mark the position on the wall where the Anchors will be placed.
   • Before marking the screw position, straighten with the integrated horizontal level.
   • Drill the marked holes using a 1/4 in. drill bit, then insert Anchors (EE).
   • Affix Back Plate to Anchors using Wall Mounting Screws (CC). Observe the horizontal level before tightening the screw.

5. Connect the Power Supply Wires
   Feed the power supply wires through the desired conduit inlet on the Back Plate. Using Wire Connectors (FF), connect wires coming from the LED driver on the

   • Back Plate to the power supply wires:
     See wiring diagram A or diagram B.

6. Re-Attach the Front Cover

   • Re-attach the Front Cover to the Back Plate and re-connect the quick-release wires.
   • Close the Front Cover and secure it with the Front Cover Screws (BB).

7. Apply Sealant
   Once the fixture is tightly secured to the wall, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.

8. Turn Power On
   Turn the power back on at the wall switch, circuit breaker, or fusebox.

Flush Mount Installation

1. Turning Off the Power
   Turn the power OFF at the wall switch, fusebox, or circuit breaker.

2. Remove the Front Cover

   • Open the Wall Light (AA) by unscrewing the Front Cover Screws (BB) using a phillips screwdriver (not provided).
   • Remove the Front Cover from the Back Plate by disconnecting the quick-connect wires and sliding the Front Cover in an upward direction.

3. Prep the Back Plate
   Drill 2 holes using a 1/4 in. drill bit on the universal knockouts on the Back Plate needed to install on your J-Box.

4. Remove the Center Knockout
   Remove the knockout on the Back Plate by using a phillips screwdriver (not provided).

5. Connect the Power Supply Wires

   • Feed the power supply wires through the knockout hole and mount the Back Plate to the J-Box using the J-Box Mounting Screws (DD).
   • Observe the horizontal level before tightening the screw.
   • Using Wire Connectors (FF), connect wires coming from the LED driver on the Back Plate to the power supply wires:
   • See wiring diagram A or diagram B.

6. Re-Attach the Front Cover

   • Re-attach the Front Cover to the Back Plate and re-connect the quick-release wires.
   • Close the Front Cover and secure it with the Front Cover Screws (BB). ****

7. Apply Sealant
   Once the fixture is tightly secured to the wall, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.

8. Turn Power On
   Turn the power back on at the wall switch, circuit breaker, or fusebox.

Wiring for a Standard Wall Switch

Wiring for 0-10V Dimmer

Operation

Lumen Switch
Select the brightness: 4000, 8000 or 12000 lumens

CCT Switch
Slide the Color Temperature switch to point to either 3K, 3.5K, 4K, 5K, 6.5K.

• 3K (3000K) – Soft White
• 3.5K (3500K) – Neutral White
• 4K (4000K) – Bright White
• 5K (5000K) – Daylight
• 6.5K (6500K) – Daylight Deluxe

D2D/MOT Switch
D2D – Motion detection is disabled. Light will remain off during the day and automatically turn on at dusk.

• NOTE:
  A Dust-To-Dawn Sensor Cover is provided to block out light and bypass the sensor. This will keep the light on continuously and the fixture can be controlled through the wall switch or a master photocell.

• MOT
  The motion sensor is activated. The light will turn on for 10 minutes when motion is detected. During this time, brightness will be at 100% and will drop to 30% of the selected lumen if no motion is detected.

• NOTE:
  There will be a warmup time for about 10 seconds when first powered up. Brightness will be at 100% and will then drop to 30% after the warmup time. Brightness will go to 100% once motion is detected.

NOTE:
The 180-degree coverage of the motion sensor is measured side-to-side. The sensor will detect motion across the field of view (see below image). The motion sensor’s maximum detection range is up to 60 ft.

Motion Detection Distance at Mounting Heights:

• 8ft: Maximum detection range is up to 60ft.
• 15ft: Maximum detection range is up to 52ft.
• 20ft: Maximum detection range is up to 40ft.

Troubleshooting

FEIT ELECTRIC COMPANY I PICO RIVERA, CA | 800-543-3348 | FAX 562-908-6360 | www.feit.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>