LEFTON BF2204 Smart Modern Rotatable Bathroom Faucet Installation Guide
- August 31, 2024
- LEFTON
Table of Contents
INSTALLATION MANUAL Single Lever Bathroom
Basin Faucet
BF2204
BF2204 Smart Modern Rotatable Bathroom Faucet
Congratulations on the purchase of your new Lefton plumbing fixture!
Please keep the box and packaging materials until your product is completely
installed. If you have any questions, require technical assistance or have any
problems with your product:
DO NOT RETURN TO STORE
Please contact our Customer Service Team
customer@leftonhome.com
Have the model number available and retain a copy of your receipt with
purchase date for reference.
If for any reason this product does not meet your expectations, please be sure
to repack this product in the original box and packaging material to avoid
damage during transit.
Prior to Installation:
- Make sure you have all necessary parts by checking the diagram andparts list. If any part is missing or damaged, please contact Lefton Customer Service at customer@leftonhome.com for a replacement.
- Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone.
- Flush angle stops to release any debris prior to installation.
- Pre-drilled hole size requirement: 13/8″ (min)
- Max countertop thickness: 1 3/4″
Tools Required
Diagram and Parts List
A. Faucet Body
B. Waterproof Rubber Ring
C.Threaded Metal Pipe
D. Rubber Gasket
E. Matel Gasket
F. Mounting Nut
G. Mounting Screws
H. Hot & Cold Water Pipes
Faucet Dimension
Installer Tip:
Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware
Shut off the water supply. Remove the old faucet. Clean the mounting
surface. Remove mounting hardware (F & G) from threaded metal pipe(C). Step
2. Installing the faucet assembly Install the waterproof rubber ring (B) and
the threaded metal pipe (C) on the faucet body (A) in sequence.
Step 3. Install hot and cold water pipes Swivel the hot and cold water
pipes (H) into the faucet body (A).
Step 4. Install faucet body to countertop Insert faucet body through the
hole in the sink or the countertop.
Step 5. Install mounting hardware Pass the rubber gasket (D), metal
gasket (E) and mounting hardware (F & G) through the metal pipe in turn and
tighten them.
When the above assemblies through the hot and cold water pipes (H), please
refer to the picture below. Step 6. Making the waterline connections
Thread the nut (1) on the supply line onto the outlet of the water supply
valve and tighten with a wrench. Do not overtighten.
Step 7. Turn the faucet on and check for leaks Turn on angle stops, turn
the faucet on and check for leaks.
(DO NOT TURN FAUCET ON BEFORE THE INSTALLATION IS COMPLETE)
Trouble-Shooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
| PROBLEM | CAUSE | ACTION |
|---|---|---|
| Leakage under faucet handle | Bonnet nut (11) has come loose | Remove the cover |
button (15). Loosen set screw (14) with hex wrench (22). Remove the handle.
Unscrew cap (12). Tighten bonnet nut (11) with an adjustable wrench.
The aerator has an irregular or reduced water flow| The aerator is dirty or
mis-fitted| Remove the aerator and check for debris. Ensure that the rubber
washer is properly installed.
The water pressure is low.| The connector underneath the deck is clogged with
debris The aerator is clogged| Turn off the water supply and disconnect the
connector / aerator. Unscrew the connector / aerator and clean under running
water. Screw the connector / aerator back.
Test water flow. If water pressure is still low then replace the connector /
aerator.
There is a low flow of water.| The screen filter in the hose connectors is
dirty.| Turn off the water supply at water valve and unscrew the hose
connectors from water supply lines. Clean the screen in the water lines with
hot water, removing any debris or calcium build up.
Care & Maintenance
To keep the product clean & shining, follow the steps below:
- Rinse with clean water & dry with a soft cloth
- Do not use cloth with a coarse surface
- Unscrew the aerator and clean when necessary Awop
- Do not clean with soaps, acid, polish, abrasives or harsh cleaners
This installation manual is subject to change without further notice.
Enjoy Smart and Creative Life
THANK YOU!
www.leftonhome.com
customer@leftonhome.com
August 25, 2022
Documents / Resources
|
LEFTON BF2204 Smart Modern Rotatable Bathroom
Faucet
[pdf] Installation Guide
BF2204, BF2204 Smart Modern Rotatable Bathroom Faucet, BF2204, Smart Modern
Rotatable Bathroom Faucet, Modern Rotatable Bathroom Faucet, Rotatable
Bathroom Faucet, Bathroom Faucet, Faucet
---|---