HIKMICRO LYNX 2.0 Series Thermal Monocular Instruction Manual
- August 30, 2024
- HIKMICRO
Table of Contents
HIKMICRO LYNX 2.0 Series Thermal Monocular
Specifications
- Model: LYNX 2.0 SERIES
- Thermal Monocular
- Battery Voltage: 3.6 V
- Battery Capacity: 3200 mAh
Product Information
Introduction
The Thermal Monocular in the LYNX 2.0 SERIES is a cutting-edge device
designed for thermal imaging applications. It provides clear and detailed
images for various purposes.
Package Content
The package includes the Thermal Monocular, lens cover, wrist strap, and a
user manual.
Appearance
The appearance of the monocular may vary slightly across different models.
Key features include lens cover, buttons for setting functions, battery
compartment, eyepiece, diopter adjustment knob, focus ring, type-C interface
for power and data transmission, charging indicator, tripod mount, and wrist
strap hole.
Product Usage Instructions
Button Description
- Power: Press to enter standby mode or wake up the device. Hold to power on/off.
- Mode: Press to switch between different modes. In non-menu mode, press to capture snapshots and hold to start/stop recording videos. In menu mode, press to confirm/set parameters and hold to save and exit the menu.
- Zoom: In non-menu mode, press to switch digital zoom and hold to correct display non-uniformity. In menu mode, press to move down.
Install Battery
Clean the battery compartment cover for better conductivity. Install a
3.6V, 3200mAh battery into the device.
Charge Device
- Ensure the battery is installed.
- Lift the type-C interface cover.
- Connect the device to a power adapter using a type-C cable.
- Check the charging indicator status: Flashing Red & Green (Error), Solid Red (Charging), Solid Green (Fully charged).
App Connection
- Download and install the app by scanning the QR code.
- Enable hotspot in the device menu.
- Connect your phone to the device hotspot using WLAN.
- Open the app to view and control the device interface on your phone.
More Operations
Refer to the user manual for detailed operational instructions.
FAQ
-
Q: How do I clean the lens of the Thermal Monocular?
A: To clean the lens, use a clean cloth to wipe gently. Avoid using harsh chemicals or abrasive materials that may damage the lens surface. -
Q: Can I use the Thermal Monocular in extreme weather conditions?
A: The Thermal Monocular is designed to withstand various environmental conditions, but it’s recommended to refer to the user manual for specific temperature and weather guidelines.
Thermal Monocular
LYNX 2.0 SERIES
Introduction
HIKMICRO LYNX 2.0 thermal monocular is equipped with a powerful infrared detector and a 1024 × 768 OLED display. Its high thermal sensitivity of less than 20 mK NETD ensures perfect image quality and detail recognition even in the hardest weather conditions. It can be applied mainly in forest & field hunting, birding, animal searching, and rescuing scenarios.
Package Content
The package includes: Device (× 1), Battery (× 2), Battery Charger (× 1), Type-C Cable (× 1), Lint-free Cloth (× 1), Protective Bag (× 1), Wrist Strap (× 1), and Quick Start Guide (× 1).
Appearance
The appearance may vary according to different models. Please take the actual
product for reference.
- Lens Cover: Protects the lens from dust or scratch.
- Buttons: To set functions and parameters.
- Battery Compartment: For holding the battery.
- Eyepiece: The piece placed closest to the eye to view the target.
- Diopter Adjustment Knob: Adjusts the dioptric setting.
- Focus Ring: Adjusts focus to obtain clear targets.
- Type-C Interface: Power the device or transmit data with a type-C cable.
- Charging Indicator: Indicates the charging status of the device.
- Tripod Mount: Mounts the tripod.
- Wrist Strap Hole: Mounts the wrist strap.
Button Description
Install Battery
Note
- To ensure better conductivity, if the battery compartment cover gets dirty, use a clean cloth to wipe the thread.
- Remove the battery if the device is not used for a long time.
- The external rechargeable battery type is 18650, and the battery size should be 19 mm × 70 mm. The rated voltage is 3.6 V, and the battery capacity is 3200 mAh.
Charge Device
Steps:
- Make sure the battery is installed in the device.
- Lift the type-C interface cover.
- Connect the device and power adapter with a type-C cable to charge the device.
- Check the charging indicator status : Flashing Red & Green: Error occurred. | Solid Red: Charging. | Solid Green: Fully charged.
Note
- You can also use the battery charger to charge the battery.
- The charging temperature should be from 0 °C to 45 °C (32 °F to 113 °F).
- Charge the device for more than 6 hours before first use.
App Connection
- Firmware Upgrade
- Browse & Save Exciting Moment
- Preview & Remote Control
- How-to Videos
- Repair Records & Warranty Details
Steps:
- Scan the QR code to download and install the app.
- Select in the device menu to enable hotspot. 3. Turn on WLAN of your phone and connect to the device hotspot.
- Hotspot Name: HIKMICRO_Serial No.
- Hotspot Password: Go to Hotspot in the menu to check the password.
- Open the app and connect your phone with the device. You can view device interface on your phone.
Note
If the password is not displayed, please upgrade the device to the latest
version. Or enter the serial No. as the password.
More Operations
Scan the QR code below to obtain the user manual for more operations.
Legal Information
© Hangzhou Microimage Software Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other reasons. Please find
the latest version of this Manual at the HIKMICRO website
(www.hikmicrotech.com).
Please use this Manual with the guidance and assistance of professionals
trained in supporting the Product.
Trademarks and other HIKMICRO’s trademarks and logos are the properties of
HIKMICRO in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective
owners.
DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”.
HIKMICRO MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL
HIKMICRO BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR
LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF
THE PRODUCT, EVEN IF HIKMICRO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKMICRO SHALL NOT TAKE ANY RESPONSIBILITY FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK,
VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKMICRO WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU
ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE
LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT
DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT
LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR
ILLEGAL HUNTING ANIMALS, INVASION OF PRIVACY OR ANY OTHER PURPOSE WHICH IS
ILLEGAL OR DETRIMENTAL TO THE PUBLIC INTEREST. YOU SHALL NOT USE THIS PRODUCT
FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF
WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR
BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR
EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
Regulatory Information
These clauses apply only to the products bearing the corresponding mark or
information.
EU Compliance Statement
This product and – if applicable – the supplied accessories too are marked
with “CE” and comply therefore with the applicable harmonized European
standards listed under the Directive 2014/30/EU (EMCD), Directive 2014/35/EU
(LVD), Directive 2011/65/EU
(RoHS), Directive 2014/53/EU.
Hereby, Hangzhou Microimage Software Co., Ltd. declares that this device
(refer to the label) is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://www.hikmicrotech.com/en/support/download-
center/declaration-of-conformity/
Frequency Bands and Power (for CE)
The frequency bands and transmitting power (radiated and/or conducted) nominal
limits applicable to the following radio equipment are as follows: Wi-Fi 2.4
GHz (2.4 GHz to 2.4835 GHz), 20 dBm
For the device without a supplied power adapter, use the power adapter
provided by a qualified manufacturer. Refer to the product specification for
detailed power requirements.
For the device without a supplied battery, use the battery provided by a
qualified manufacturer. Refer to the product specification for detailed
battery requirements.
Directive 2012/19/EU (WEEE Directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
Directive 2006/66/EC and its amendment 2013/56/EU (Battery Directive): This
product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific
battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a designated collection
point. For more information see:
www.recyclethis.info.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Please read all the safety information carefully before using.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical
safety regulations.
Transportation
- Keep the device in original or similar packaging while transporting it.
- Keep all wrappers after unpacking them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper.
- Transportation without the original wrapper may result in damage on the device and the company shall not take any responsibilities.
- Do not drop the product or subject it to physical shock. Keep the device away from magnetic interference.
Power Supply
- The input voltage for the device should meet the Limited Power Source (5 VDC, 2 A) according to the IEC62368-1 standard. Please refer to actual products and technical specifications for detailed information.
- Make sure the plug is properly connected to the power socket.
- DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload.
- The power source should meet limited power source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.
Battery
- The external rechargeable battery type is 18650, and the battery size should be 19 mm × 70 mm. The rated voltage is 3.6 VDC, and the battery capacity is 3200 mAh.
- For long-term storage of the battery, make sure it is fully charged every half year to ensure the battery quality. Otherwise, damage may occur.
- CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Replace with the same or equivalent type only.
- Batteries of improper size cannot be installed, and may cause abnormal shutdown.
- Please purchase the batteries recommended by the manufacturer if necessary.
- The purchased batteries by users need to comply with the relevant international standards about battery safety (e.g. EN/IEC standards).
- Make sure the battery temperature is between 0°C to 45°C (32°F to 113°F) when charging.
- Confirm there is no flammable material within 2 m of the charger during charging.
- DO NOT place the device with battery or the battery alone near heating or fire source. Avoid direct sunlight.
- DO NOT place the battery in the reach of children.
- DO NOT swallow the battery to avoid chemical burns.
- Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types).
- Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.
- Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.
- Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.
- Dispose of used batteries according to the instructions.
Maintenance
If the product does not work properly, please contact your dealer or the
nearest service center. We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
Wipe the device gently with a clean cloth and a small quantity of ethanol,
if necessary.
If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the device may be impaired.
Clean the lens with soft and dry cloth or wiping paper to avoid scratching
it.
Using Environment
- Make sure the running environment meets the requirement of the device. The operating temperature shall be -30 °C to 55 °C (-22 °F to 131 °F), and the operating humidity shall be from 5% to 95%.
- DO NOT expose the device to high electromagnetic radiation or dusty environments.
- DO NOT aim the lens at the sun or any other bright light.
- Place the device in a dry and well-ventilated environment.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing Subdistrict, Binjiang
District, Hangzhou, Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might be subject to export
controls in various countries or regions, including without limitation, the
United States, European Union, United Kingdom and/or other member countries of
the Wassenaar Arrangement. Please consult your professional legal or
compliance expert or local government authorities for any necessary export
license requirements if you intend to transfer, export, re-export the thermal
series products between different countries.