VigilLink S902 UHD Quad View Processor User Guide
- August 28, 2024
- VigilLink
Table of Contents
- S902 UHD Quad View Processor
- Product Information
- Specifications:
- Product Usage Instructions:
- 1. System Connection:
- 2. Using IR Remote Controller:
- 3. System Reset:
- 4. System Control:
- 5. OSD Menu Structure:
- Q: How do I switch between different display windows?
- Q: Can I adjust the image size and location in each output
S902 UHD Quad View Processor
Product Information
Specifications:
-
Model: S902
-
Type: 4×2 UHD Quad View Processor with Seamless switcher
-
Inputs: 4x HDMI 2.0
-
Outputs: Dual UHD outputs
-
Maximum Input Resolution: 4096 x 2160 @60Hz, 4:4:4 chroma
sampling -
Features: True 10-bit processing, up/down scaling, multiple
display windows with flexible image size, cropping, location, and
overlap
Product Usage Instructions:
1. System Connection:
Connect the HDMI input sources to the respective ports on the
processor. Connect the dual UHD outputs to your displays.
2. Using IR Remote Controller:
Use the provided IR remote controller to navigate through
different display modes and settings.
3. System Reset:
Perform a complete system reset through the RESET HOLE using a
small pin or similar tool. Alternatively, reset through the IR
controller or OSD.
4. System Control:
Control the system using different methods such as RS232 or
Ethernet connection. Refer to the user manual for detailed
instructions.
5. OSD Menu Structure:
Access and navigate the OSD menu using the keypads on the front
panel. Save and backup/restore system data in a PC for future
use.
FAQ
Q: How do I switch between different display windows?
A: You can switch between different display windows by using the
IR remote controller or navigating through the OSD menu using the
front panel keypads.
Q: Can I adjust the image size and location in each output
window?
A: Yes, you can adjust the image size, cropping, and location of
each display window to suit your preferences using the processor’s
features.
S902 User Guide
Document: S902-2
S902 User Guide
4×2 UHD Quad View Processor with Seamless switcher
4x HDMI 2.0 input and dual UHD outputs Maximum input: 4096*2160 @60Hz, 4:4:4
chroma sampling with the same or different display Windows in each output
Multiple display windows with flexible image size, cropping, location and
overlap Seamless switching in single or multi-view display modes.
Image fade in, fade out, dissolve, and wipe True 10-bit processing and up/down
scaling.
Sales & Technical support Website : www.VigilLink.com
E-mail : info@vigillink.com Version:1.02
Tel : +949-701-4742
0
S902 User Guide
Document: S902-2
Table of Contents
Introduction …………………………………………………………………………………………………… 3
Outlook
Front panel……………………………………………………………………………………………..
4
Back panel ………………………………………………………………………………………………………………………..5
System Connection ……………………………………………………………………………………….. 6
Content in the packing box …………………………………………………………………………….. 7
User Guide
1. How to use IR Remote Controller……………………………………………………………..
7
1.1. P-100 Controller for User Preset Modes Recall ………………………………………………………………7
1.2. RC-902 Controller for System Setup…………………………………………………………..
8
1.3. Limitation in OSD Operation………………………………………………………………………………………….9
1.4. IR Receiver Extender……………………………………………………………………………..
9
1.5. OSD Lock and Unlock……………………………………………………………………………
9
1.6. OSD Menu keypads on the Front Panel………………………………………………………………………….9
2. System Structure …………………………………………………………………….. 10
2.1. OSD Menu location ……………………………………………………………………………………………………….10 2.2. Display
Window ………………………………………………………………………………………………………….. 10 2.3. Output Ports
……………………………………………………………………………………………………………….. 10 2.4. Limitations in Output
Port……………………………………………………………………………………………. 10
3. System Reset
3.1. Complete System Reset through RESET HOLE…………………………………………………………….. 10 3.2.
Reset Through IR Controller or OSD…………………………………………………………………………….. 10
4. System Control ……………………………………………………………………….. 11
4.1. Control Method …………………………………………………………………………………………………………… 11 4.2.
RS232…………………………………………………………………………………………………………………………. 11 4.3. Ethernet
Connection……………………………………………………………………………… 11
5. System Data SAVE and Backup/Restore in PC…………………………… 11
6. OSD MENU Structure……………………………………………………………………….. 12
6.1. OUTPUT SETUP …………………………………………………………………………………………..
12
– OUTPUT MODE ………………………………………………………………………………………………………. 12 – INPUT SELECT……………………………………………………………………………………………………….. 12 – AUDIO SELECT………………………………………………………………………………………………………. 12 – RESOLUTION …………………………………………………………………………………………………………. 12 – TRANSITION / DURATION……………………………………………………………………………………….. 13 – PRIORITY (OUTPUT 1 / OUTUT 2) ……………………………………………………………………………. 13 – HDCP …………………………………………………………………………………………………………………….. 13
1
S902 User Guide
Document: S902-2
6.2. WINDOW SETUP ………………………………………………………………………………. 14
– INPUT SELECTION …………………………………………………………………………………………………. 15
– SCALING ……………………………………………………………………………………………………………….. 15
– WINDOW………………………………………………………………………………………………………………… 15
– PICTURE………………………………………………………………………………………………………………… 15
– COLOR………………………………………………………………………………………….. 16
– DE-INTERLACING……………………………………………………………………………..
16
– NOISE REDUCTION ………………………………………………………………………………………………… 19
– MISCELLANEOUS ………………………………………………………………………………………………….. 19
6.3. SYSTEM ………………………………………………………………………………………. 20
– PROFILE………………………………………………………………………………………… 20 – EDID ………………………………………………………………………………………………………………………. 20 – OSD……………………………………………………………………………………………………………………….. 20 – STANDBY ………………………………………………………………………………………………………………. 21 – ETHERNET …………………………………………………………………………………………………………….. 21 – RS232 ……………………………………………………………………………………………………………………. 21 – BOX ID …………………………………………………………………………………………………………………… 21 – NAME …………………………………………………………………………………………………………………….. 21 – RESET …………………………………………………………………………………………………………………… 21 – VERSION ……………………………………………………………………………………………………………….. 21
7. S902 Control TOOL (SCT) & Web UI ………………………………………….. 22 8. Call for
technical support …………………………………………………………. 26 9. Safety Precaution and
Maintenance ………………………………………….. 26 10. Warranty and RMA policy
……………………………………………………….. 27
10.1. Warranty………………………………………………………………………………………………………………….. 27 10.2. RMA
Policy ……………………………………………………………………………………………………………… 27
Specifications………………………………………………………………………………………………… 28
Disclaimer/Copyright statement ……………………………………………………………………………………………….. 29
Warranty/RMA and FCC/CE statement………………………………………………………………………………………. 29
Revision history …………………………………………………………………………………………….. 30
2
S902 User Guide
Document: S902-2
Introduction
The S902 is a 4×2 UHD Quad-View processor that allows users to display up to
four 4k/60 sources simultaneously on one or two UHD displays. This device
offers a highly flexible and cost-effective solution for routing up to four
4k/60 sources to two separate displays simultaneously. Users can choose from
12 default multi-view layout presets and 20 custom Profile Presets to
customize their display mode.
Featuring 4 HDMI 2.0 inputs and 2 HDMI 2.0 outputs, the S902 supports CEA
video standard timings up to 4096*2160 @60Hz with 4:4:4 chroma sampling. Each
output port can accommodate up to 4 windows, with each window capable of
selecting an input source from any input port. Users have the option to assign
the same input source to multiple windows and can adjust input selection,
image positioning, resizing, cropping, and color settings for each window.
Users can prioritize display windows when they overlap and select one or
multiple windows with the same configuration for any output port. The device
offers 16 transition modes, including high speed seamless switching, Fade-in,
Fade-out, Dissolve, and Wipe, with selectable duration for transitions. It
integrates HDMI embedded audio, RCA SPDIF digital audio, and analog 3.5mm R/L
audio jack R/L, allowing users to assign audio from input ports to each audio
output port as needed.
Control options for the unit include IR controller, front panel push button,
USB, WebUI, RS232 and Ethernet, providing versatile control methods for
various applications. Users can recall up to 20 custom Profile Presets through
different control systems. Designed for continuous operation in a 24/7
environment, the S902 offers easy configuration, low entry barriers, cost-
effectiveness, reliability, and flexibility for a wide range of applications.
Application
– Front end processor for large display, such as LED, edge blending system,
video wall. – Digital signage – Presentation halls – Security & surveillance
systems – Education – Conference room – Video content post production – Video
editing studio
3
S902 User Guide
Outlook
Document: S902-2
Front panel
Three functions Seamless input selection OSD function key after activate OSD
menu Profile SAVE/RECALL Index # keys
Hotkey to load Custom Profile
Preset-1 Preset-2
Quad / Single display hotkey
Input LED
Output LED
IR Receiver
Hotkey to save Custom Profile
INFO key
1. Input LED will show RED light when S902 detects signal source signal in
that input port. Once it had been selected to show on the Window, it will turn
to GREEN light.
2. When turn-off Power by IR controller, the power LED will turn to RED. User
can power up by IR Controller (P-100 or RC-902) or power switch.
3. The function in CH/SELECT key is changed to OSD LOCK key. 4.
Preset-1/Preset-2 keys is to recall system Preset-1 and Preset-2 with one
window in Left and 3
windows in the Right side. One is PIP another is POP. 5. Profile Save: it will
show “SAVE PROFILE” message. User can select Profile #1 to #5 key on front
panel to save this Custom Profile. 6. Profile Recall key will show “LOAD
PROFILE” message. User can recall Profile #1 to #5 directly. 7. These Custom
Profile #1 to #5 are the same Profile Index as that inside OSD menu. 8. When
power LED is blinking, the OSD menu had been locked.
4
S902 User Guide
Document: S902-2
Back panel
User can connect signal source to any of the input ports for two output ports.
Analog audio RH/LH output
Reset Hole
System control: RS232, USB, Ethernet
HDMI 2.0 input source
SPDIF Audio output
Video Outputs
IR Extender connector
DC 12V/2A connector
1. OSD Menu can only show in Output-1 channel. 2. Window-1 and Window-2 will
have full functions OSD menu. “De-Interlacing” and “Noise Reduction”
OSD menu will only be available in Window-1 and Window-2. 3. Except OSD Menu
difference, Window-3 and Window-4 will have the same function and video
quality as Window-1 and Window-4. 4. User can select audio source for each
output port, SPDIF and Analog R/L output independently. 5. Every input signal
source (HDMI-1 to HDMI-4) can be assigned to one or multiple Windows.
5
S902 User Guide
Document: S902-2
System Connection
Each display Window can select signal from any input port. Each output can
display up to 4 windows. Each window can be located at any position with
flexible resizing, cropping, aspect ratio, color correction and overlap
priority setting.
Output ports configuration
OSD can only be showed in Output-1. User can assign any display Window for
each output. Maximum is 4 windows. If any Window is assigned to both output
ports, the Window content, layout and position must be the
same. If each output shows different Windows, user can flexibly manipulate the
Windows without affecting
another Output port.
6
S902 User Guide
Document: S902-2
Content in the packing box
The S902 Quad View Processor 1x RC-902 IR Controller 1x IR Extending Receiver
with 1.8m cable 1x AC to DC Power supply unit with Power Cord Mounting bracket
with screw (Option) P-100 Profile Control IR Controller (Optional) Please
download User Guide & Web UI Tool at www.vnstw.com.
User Guide
1. How to use IR Remote Controller
– RC-902 is standard controller for system setup. – P-100 is simplified
controller for end user. The operation will not affect system Setup. It is an
option
item to buy separately.
1.1. P-100 Controller for User Preset modes recall
– Directly click number keys 1-10 will recall Custom Profile 1-10.
– If click Blank key first, then click other number key, it can recall Custom
Profile 11-20.
– Click “S” key will pop-up Input/Output and FW version system information.
7
S902 User Guide
1.2. RC-902 Controller for system Setup
Custom Profile Recall Menu hotkey (#1-#20)
Custom Profile Recall keys Image cropping Image Background Window name Menu
Image Transition Menu OSD Lock/unlock Save setting hotkey
Document: S902-2
Input signal information
Select display window with full screen display Select Preset modes
OSD Menu operation Activate OSD Menu Select Input port Select Output
resolution One window display Quad window display Adjust Window size Adjust
Window position Set window display priority Select audio source
System reset
8
S902 User Guide
Document: S902-2
1.3. Limitation in OSD Operation
OSD Menu can only show in Output-1 channel. Window-1 and Window-2 will have
full function OSD menu. “De-Interlacing” and “Noise Reduction”
OSD menu will only be available in Window-1 and Window-2. User can select
audio source for each output HDMI, SPDIF and Analog R/L output independently.
1.4. IR Receiver Extender
RC-902 controller is specific for the operation of S902. IR receiver is on
Front Panel. One 3.5ø mm audio connector for IR extender is located at Back
Panel of S902. 1.8m IR extension cable is equipped in the packing. User can
add 2.5Ø audio cable to extend the control distance up to 20 meters.
Audio connector for IR extender
1.5. OSD Lock and Unlock
To press LOCK key on RC-902 controller for 5 seconds will LOCK the OSD. [Menu
Lock] message will show on the screen. To press another 5 seconds on LOCK key,
it will UNLOCK the OSD. [Menu Unlock] message will show on the screen.
On front panel, MENU key has the same function as LOCK key in IR controller.
OSD Lock can also be used while multiple units of GeoBox are used
simultaneously to prevent
mutual interference. When OSD is locked, Power LED on front panel will be
blinking.
1.6. OSD Menu keypads on the Front Panel
Front panel has OSD keypads. The functions are the same as IR controller. The
only difference is in the hotkeys function. Please see more details in “Front
Panel” section.
9
S902 User Guide
Document: S902-2
2. System structure
2.1 OSD Menu location
– OSD will only display on Output-1.
– OSD menu is location at top left corner. 2.2 Display Window
– One output can display up to 4 Windows. – Each Window can select signal
source from any HDMI input port. – Each Window has independent color
correction and settings. – One HDMI signal can be assigned to multiple
Windows. 2.3 Output ports
– One output can display up to 4 Windows. – Each Window can select signal from
any HDMI input port. 2.4 Limitations in output display
– OSD can only be showed in Output-1 – Each output can display up to 4
Windows. – The Window position, size and cropping in two output ports will be
the same. – User can select different Windows for each output with different
setup. – If each output shows different Windows, user can have flexible
Windows setup without affecting
another Output port.
– Window-3 and Window-4 will have no de-interlacing function. It will execute
double scaling for
interlaced signal. We suggest using progressive signal to get the best video
quality.
3. System Reset
3.1. Complete system reset through RESET hole
– Inserting small pin into RESET hole on back panel for 5 seconds will reset
the system to default settings. It will erase all Custom Preset Profile data.
3.2. Reset through IR controller or OSD
– User can Reset through OSD menu under [System] [Reset]. – Click IR control
[RESET] key will Pop-Up System Reset OSD menu. – Custom Profile Data will
remain the same without being erased.
10
S902 User Guide
Document: S902-2
4. System Control
4.1. Control method
– User can control S902 through IR controller, front panel keypads, USB, RS232
and Ethernet. – S902 control tool is available for USB control and WebUI is
embedded in S902 for Ethernet control.
4.2. RS232
RS232 interface is designed with DB-9 connector. User can select 11520 or 9600
baud rates. The UART Protocol between GeoBox and a Host computer can be
downloaded from website. The
protocol can be executed via RS-232, Ethernet or other forthcoming
communication methods. Box ID is available from OSD setting when multiple
units are used at the same time.
4.3. Ethernet connection
User can control and setup S902 through network connection and embedded WebUI.
UTP cable can be used for direct connection between PC and GeoBox. User needs
to set PC
TCP/IPv4 with the same domain segment as GeoBox (for instance, to set IP
address at (192.168.0.105) and subnet mask at (255.255.255.0). Open web
browser (Google Chrome or Internet Explorer) and input S902 IP address
(default is 192.168.0.100), user can see GeoBox WebUI and menu for further
system operation. There is no additional software is required. If user can’t
connect the network, please power off/on S902 again to let PC detect S902
network. If the connection is gone through WiFi router or switch/hub through
RJ45 to Lan port, user can set DHCP IP or Static IP for the connection. If
necessary, please [Renew] DHCP to get IP address for network connection. Each
S902 can set different IP address for independent operation and control. If
S902 is connected with WiFi Router (through LAN port), user can control S902
through WiFi via PC, iPad or mobile phone through the same SSID. User can set
different IP in each S902 for individual control while multiple units are
used. Default TCP server port is 1266.
5. System data SAVE and Backup/Restore in PC
To use SAVE hotkey and select Index # to store custom setting through OSD.
System data backup and restore in PC should be done through SCT control tool.
11
S902 User Guide
6. OSD Menu structure
6.1. OUTPUT SETUP
Below is the menu under OUTPUT SETUP:
Document: S902-2
OUTPUT MODE
12 output modes can be selected, including single Window full screen display
and Quad Window display.
INPUT SELECT
– Each HDMI input signal can be assigned to any display Window. – Each Window
can be assigned to Output-1, Output-2, Both or turn off.
AUDIO SELECT
User can select from 4 input sources audio for Output-1, Output-2, SPDIF
output or Analog output. Analog output audio is abstracted from SPDIF audio.
RESOLUTION
– User can select output resolution from 14 preset resolutions. – Two output
channels will have the same output resolution.
12
S902 User Guide
Document: S902-2
TRANSITION / DURATION
– 18 transition effects are built in the processor. It includes Quick
Seamless, Fade in/Fade out, Dissolve and Wipe.
– Transition effect only implemented during input source or display mode
change. – Each effect can select different duration. – User can save
Transition setting in Custom Profile mode together with input selection and
Window
configuration. When selects this Preset mode, user will see Transition effect.
– Fade-in/Fade-out can be executed in both single and multiple Windows display
modes. Dissolve and
Wipe transition modes can only be executed with single Window display. – The
duration range in different Transition modes may be different.
PRIORITY (OUTPUT 1 / OUTPUT 2)
To set each window display priority when they are overlapped. Each Window can
be at different layer. User can use WebUI to select Priority for each Window
freely. Each Output can be set independently through OSD.
HDCP
– AUTO: When the input is HDCP compliant, the box will execute HDCP control in
both input and output.
– ON: no matter input is HDCP compliant or not, it will always control HDCP. –
Off: When the input is HDCP compliant and the output is not HDCP compliant,
the processor will turn
off output display.
13
S902 User Guide
Document: S902-2
6.2. WINDOW SETUP
WINDOW-1/WINDOW-2: with full function of OSD menu. WINDOW-3/WINDOW-4: No DE-
INTEERLACING and NOISE REDUCTION OSD Menu.
14
S902 User Guide
Document: S902-2
INPUT SELECTION
– Each Window can select any input signal source from HDMI-1 to HDMI-4. – Each
HDMI input signal can be assigned to multiple Windows.
SCALING
– RATIO: o FULL: To show image with full Window. o ASPECT: To show image with
source original aspect ratio. o Different selection will affect Window size
and position adjustment.
– CROP: o To adjust image Horizontal and Vertical Start and End points
coordinates. o It can crop any location of the source image in each Window. o
IR controller CROP Hotkey can only ZOOM-IN / ZOOM-OUT source image from the
center.
– ASPECT H-POS / V-POS: When the image is not full screen display in the
Window, user can adjust the image position based on the same aspect ratio
through this function.
– RESET: To reset the image to default setting in all functions under SCALING.
WINDOW
– H-POS / V-POS: To adjust Horizontal and Vertical positions of the image. The
image will keep the same aspect ratio.
– WIDTH: To adjust the image location in Right Edge with Left Edge at fixed
location. It can change image horizontal aspect ratio. If will be affected by
SCALING selection.
– HEIGHT: To adjust the image location in Bottom Edge with Top Edge at fixed
location. It can change image vertical aspect ratio. If will be affected by
SCALING selection.
– LEFT POD: To adjust image Left Edge position with Right Edge at fixed
location. It can change horizontal aspect ratio. If will be affected by
SCALING selection.
– TOP POS: To adjust image Top Edge position with Bottom Edge at fixed
location. It can change vertical aspect ratio. If will be affected by SCALING
selection.
– IR controller POSIT and SIZE hotkeys can implement the same function.
PICTURE
– FORMAT: To show input source Format. – BRIGHTNESS, CONTRAST, H-SHARPNESS,
V-SHARPNESS – HISTOGRAM: To show image histogram at real time.
15
S902 User Guide
Document: S902-2
COLOR
– Color adjustment for Chromaticity color gain, Hue, Color Temperature
(6500k/9300k) – GAMMA1 MODE: input signal gamma curve selection. – GAMMA2
MODE: output signal gamma curve selection. The vision feeling change in low
brightness
image will be more obvious. – COLOR CORRECTION: Blue, Adjust color gain in
Blue, Green and Skin Tone.
DE-INTERLACING (Pictures from Genesis Microchip)
– This function is for user to select different de-interlacing method in video
editing. – The major application is for interlaced signal source such as
2160i, 1080i, 480i… which user can only
see odd frame or even frame in one time. Properly conversion of interlaced
signal into progressive signal will get the best video quality especially in
motion picture. – When de-interlacing is turned off, it will implement double
scaling to fulfil complete video frame. – Below are some examples:
ODD Field
EVEN Field
Incorrect Pairing
Correct Pairing
16
S902 User Guide
Document: S902-2
– Motion picture field pairing (2:3/2:2 Pull Down):
24 frames/second film transferred to 60/50 frames video: o 2:3 Pull-Down: 1st
frame2 frames, 2nd Frame3 frames, 2 5, 24 60 o 2:2 Pull Down: increase film
speed to 25 frames/second, then each frame
transferred to 2 frames video. 24, 25 50
Incorrect 2:3/2:2 Pull Down
Correct Cadence field pairing Incorrect field paring
Correct 2:3/2:2 Pull Down
17
S902 User Guide
– Diagonal Processing:
Document: S902-2
Without Diagonal Correction
With Diagonal Correction
With correct cadence
Without correct cadence pairing
PS. Usually, the default is to turn on all functions under DE-INTERLACING. In
some Lab, user can turn on/off some functions to verify the type of the video
source (such as the video is 3:2 or 2:2 Pulldown) for further video editing.
It can also be used in the school for video teaching class to under different
video functions.
18
S902 User Guide
Document: S902-2
NOISE REDUCTION
– The video content may come from different signal sources, such as PC, video
camera, DVD, broadcasting, de-compressed video, de-compressed image… Each
signal source may preserve different types of noise.
– S902 allows user to select different reduction type to execute the best
noise reduction effect based on different video content.
– Only available in Window-1 and Window-2.
MISCELLANEOUS
– S902 doesn’t have image 90/270 degrees rotation function and only can do UP-
SIDE DOWN and HORIZONTAL FLIP.
– FREEZE is to stop the video at some specific point. – BACKGROUND COLOR: only
Black and Blue color background can be selected at this moment.
Customized color or pattern will be added in the future.
19
S902 User Guide
6.3. SYSTEM
Below are OSD structure under SYSTEM.
Document: S902-2
PROFILE
– LOAD: Load custom Profile from PROFILE 1 – PROFILE 20. – SAVE: Save custom
Profile to PROFILE 1 – PROFILE 20.
EDID
– Each input port can select different EDID. – 12 preset EDID can be selected
for each input port.
OSD
– User can set OSD transparent effect from 0-100%. – OSD turn off time can be
from 0-120 seconds. When select “0”, the OSD will not disappear until touch
OSD keypad or system mode change.
20
S902 User Guide
Document: S902-2
STANDBY
– When no input signal, S902 will turn off output signal and get into sleeping
mode. – Once input signal is detected, the system will turn on automatically.
– The time to get into sleeping mode is from 0-300 seconds. When select “0”,
the system will maintain
active without turn off output signal.
ETHERNET
– STATIC: o Default static IP address is 192.168.0.100. User can open PC
Chrome or Edge and input S902 IP address to get WebUI for system control. o
User can change IP address, Subnet Mask and Default Gateway manually.
– DHCP: User can also select DHCP when the system is connected with Ethernet
switch/hub or router. – After connection, user can will see WebUI to execute
S902 system setup and control. The same
network segment setting in PC is required if connect PC and S902 directly with
UTP cable. – Apple Mac or iPad can be used for the control of S902 through
network connection.
RS232: Two baud rates can be selected for RS232 control: 115200 and 9600.
BOX ID
– BOX ID is designed for independent GeoBox control in RS232 command. User can
set different IP address in Ethernet to control multiple units of GeoBox.
– The range from BOX ID is from 0-99.
NAME
– User can change the name in WINDOW 1-4 and input ports HDMI 1-4. – The
maximum digital of the name is 10. Text, symbol and number are available for
selection. – User can reset the setting through RESET key under this menu.
RESET
– User can reset the system to default setting. Customer PROFILE will not be
erased. – User can also reset the system through RESET hole on the back panel.
Please insert small pin into
RESET hole for 5 seconds and “Factory Reset” will show up. This reset will
erase all custom Profile data and the system will return to Factory Default at
the same time.
VERSION
To show up Firmware Version of the system
21
S902 User Guide
Document: S902-2
7. S902 Control Tool (SCT) & Web UI
S902 can be controlled through SCT through USB. The PC needs to support Web
HID interface.
Below is the compatibility list at this moment. Chrome/Edge/Opera can fully
support it.
(Document from MDN Web Docs)
WebUI is another control tool that is embedded inside S902 and need to connect
through network. It
can be used in any web browser. The outlook and operation of these two control
tools are similar and SCT tool may have some functions that WebUI hasn’t. If
direct Network connection is required with UTP cable, please set the same
Network segment in PC.
7.1. Open S902 Control Tool (SCT) and WebUI
SCT Tool: o Click SCT to open the tool. It will show up Control Window. o
Click [Connect] button and select USB for the connection.
WebUI: o User can also use all kind of Web Browser and S902 IP address to
access WebUI.
22
S902 User Guide
Document: S902-2
o Please change IPV4 setting to get the same Network segment and input S902 IP address for the connection. User will see WebUI control Window for further operation. Apple Mac and iPad can also be used in WebUI control tool.
7.2. After click OUTPUT SETUP, user can see below window to select system preset mode and output resolution for two outputs at the same time. If user wants to select windows for different outputs, please use OSD to do the setup.
23
S902 User Guide
Document: S902-2
7.3. When click PROFILE button, user will see below window and SAVE or LOAD custom Preset Mode in Index-1 to Index-20. The Index will be highlighted when it has been stored with Profile Data.
7.4. WINDOW SETUP allows user to select input source, set overlap priority and
set Window position, size and aspect ratio freely.
Click [Refresh] button to let operation window match actual layout of the
windows. Click and hold to draw the Window position. Click and hold control
point to adjust image size. Below sliding bar can also adjust window size and
position.
User can select Window Input source and set overlap priority.
24
S902 User Guide
Document: S902-2
7.5. SYSTEM: allows user to reset the system and system DATA Backup/Restore in PC.
RESET: ALL RESET: Reset all settings except Custom Profile data. FACTORY
RESET: Reset all settings including Custom Profile Data to factory default.
BACKUP/RESTORE: SAVE: To save system data in PC DOWNLOAD Folder. User can
rename file name. RESTORE: To restore system data from PC.
Firmware version is showed at Bottom Left corner.
PS. WebUI doesn’t support BACHUP and RESTORE functions at this moment.
7.6. Firmware Update: allows user to update the FW through SCT but not WebUI..
Load File: to select the Firmware (binary file) and click START to update the
Firmware. The update time is around 22 seconds. After Update the FW, please
insert small pin into back panel RESET hole for 5 seconds to erase all
unnecessary settings inside the system.
PS. WebUI doesn’t support Firmware Update function at this moment.
25
S902 User Guide
Document: S902-2
8. Call for technical support
User can send e-mail to support@vigillink.com together with as much
information as possible. The following information is required for a swift
response.
– Sink device (monitor): type and model number – Monitor layout or specific
application details – GeoBox model No. and series No (On back label) –
Detailed timing of signal source and resolution. – Press [Info] key to get
System Information and send the data to us, including input/output
timing and F/W version. – The exact nature of the problem. Please be as
detailed as possible. – If possible, please attach the Pictures of the issue.
Usually, we will response with 24 hours (working day) Please note that if the
machine is sent back for repair, user needs to pay for return delivery cost.
9. Safety Precaution and Maintenance
Power Supply Please connect electric power for all devices in the system from
the same Power Distribution Box with correct grounding. Open the power after
finishing system connection to reduce the risk for system damage from high
floating voltage.
Working Environment Please locate S902 in an environment free from dust,
moisture and high temperature with good ventilation.
Maintenance and Repair Apart from what is detailed in User Guide, maintenance
should be carried out by competent technician assigned by VIGILLINK. If S902
is physically damaged, it should be returned for repair using VIGILLINK RMA
procedures. If the unit is opened by user, it will lose the right for warranty
protection.
26
S902 User Guide
Document: S902-2
10. Warranty and RMA policy
10.1. Warranty
This device is designed and tested to the highest standards and backed by two
years’ parts and labor warranty. Warranties are effective upon the first
delivery date to the end customer and are nontransferable. Warranty period
extension is available up to 5 years through paying extra charges.
10.2. RMA Policy
Return Material Authorization (RMA)
In the event that a product needs to be returned for repair, inform
manufacturer and ask for a Return Material Authorization number. RMA
procedures:
1. Prior to returning any item, user must receive a Return Material
Authorization (RMA) number. 2. All RMA numbers must appear on the return-
shipping label. 3. All RMA numbers are valid for ten (10) days from the issue
date. 4. All shipping and insurance charges in all RMAs must be prepaid by the
customer.
Shipping charges and repair fees
1. Within warranty period: The customer shall pay shipping charges when the
unit is returned for repair. Manufacturer will pay shipping charges for return
shipment to customer. All the inspection, material and repairs fees shall be
borne by manufacturer.
2. Outside warranty period: · User shall pay for the inspection, material and
labor cost for the repairs and pay for all shipping freight and insurance
cost. · Manufacture shall give quotation to user and user can make decision
whether this repair shall be executed or not. If user decides to return the
unit, user shall pay for the return cost.
27
S902 User Guide
Document: S902-2
Specifications
Input ports: 4x HDMI 2.0. Max. input resolution: 40962160 @60Hz. Supports
interleaved and progressive input signals with 4:2:0/4:2:2/4:4:4, 8/10-bit
color. Supports CEA standard video timings with high end scaling up and down
up to 600 MHz. Two simultaneous HDMI 2.0 output displays with the same output
resolution, shared the same signal
sources and display Windows. Each Window can select one input signal from any
input port. The same signal source can be assigned
to the two different windows. Each output display shows up to 4 Windows with
flexible window location, resizing, scaling, positioning,
cropping and color correction. PIP/POP and Overlapping are included. User can
set Overlap priority in each output port separately. If two output ports
select the same display Windows, it will show the same Window setup. If select
different Windows, user can adjust Window setup independently. Support 16
Transition effects including Seamless, Fade-in, Fade-out, Dissolve and Wipe.
Only Fade-
in/Out is functional in multiple Windows mode switching. Seamless switching in
source selection and display mode switching. Output signal: Progressive full
color RGB 4:4:4. HDCP: V2.2/V1.4 compliant. Support xvYCC 8/10/12-bit wide
color gamut input signal processing. 1-2 frame latency based on different
application: 16.7ms-33.3ms (V=60Hz) Preset 14 output timings and 12 EDID from
XGA to 38402400 @60 for each input port. Selectable OSD transparency and
turn-off time. Image freeze, flip and upside down. Box ID for multiple boxed
individual control. Standby mode to allow user cuts off output signal when no
input signal is detected. Control: Front panel keypad, IR remote controller,
RS232, USB control tool, Ethernet, WebUI. 12 system presets and 20 custom
Profile presets. The preset includes transition effect. Selectable high end
video processing: 3:2/2:2 cadence, diagonal correction and noise reduction.
High quality scaling engine for image scaling up and down in the range from
XGA to 4k/2k. 3D motion adaptive de-interlace for interlaced input. Embedded
HDMI audio, SPDIF digital and analog R/L 3.5mm Jack audio outputs. Each audio
output can
select independent audio source from the inputs. ESD Protection: ±15kV (Air-
gap discharge), ±8kV (Contact discharge) DC power supply: DC adapter: 12V 2A
(100V-240V), max. Power consumption: 22.5W, standby: 1.9W Working environment:
40C, 10-90% RH Dimensions (Body only): 440mm160mm41mm (without protruding
parts). Weight: 2.4kg (body only) CE/FCC/RoHS Certified 2 Year Warranty,
extension package is available up to 5 years.
Prospect functions in the future
UDP control through Ethernet. Chromakey function. Programmable background with
customized picture and logo.
28
S902 User Guide
Document: S902-2
Disclaimer/Copyright Statement Copyright 2024, VNS Inc. All Right Reserved
This information contained in this document is protected by copyright. All
rights are reserved by VNS Inc. VNS Inc. reserves the right to modify this
document without any obligation to notify any person or entity of such
revision. Copying, duplicating, selling, or otherwise distributing any part of
this document without signing a non-disclosure agreement with an authorized
representative of VNS Inc. is prohibited. VNS Inc. makes no warranty for the
use of its products and bears no responsibility for any error of omission that
may appear in this document. Product names mentioned herein are used for
identification purposes only and may be trademarks of their respective
companies.
Limited Warranty and RMA statement
This device is designed and tested to the highest standards and backed by two
years’ parts and labor warranty. Warranties are effective upon the first
delivery date to the end customer and are nontransferable. Warranty related
repairs include parts and labor, but do not include repair of faults resulting
from user negligence, special modifications, abuse (mechanical damage),
shipping damage, and/or other unusual damages. The customer shall pay shipping
charges when the unit is returned for repair. Manufacturer will pay shipping
charges for return shipments to customers.
Manufacturer does not assume responsibility for consequential damages,
expenses or loss of revenue, inconvenience or interruption in operation
experienced by the customer. Warranty service shall not automatically extend
the warranty period.
User can pay extension fee to extend the warranty period. Please contact us
for more details. In the event that a product needs to be returned for repair,
inform manufacturer and ask for a Return Material Authorization number.
FCC/CE statement This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential / commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own
expense.
29
S902 User Guide
Document: S902-2
Revision History
Revision
Date
V1.00
2024-0305
V1.01
2024-0315
V1.02
2024-0322
Originator Steve Wang Steve Wang Steve Wang
Comments First version Add WebUI user guide Content update
30
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>