VigilLink VLIP-SD10G-CTRL Ultra Compact HDMI 2.0 SDVoE Fiber AV Over IP Receiver User Manual

VigilLink VLIP-SD10G-CTRL Ultra Compact HDMI 2.0 SDVoE Fiber AV Over IP

Receiver

Product Information

Specifications

• Video Input: 1 x SFP+ (10GBase-SR)
• End-to-End Time Latency: Zero-frame latency
• Output Video Port: 1 x HDMI
• Input/Output Video Resolutions: Supports resolutions up to 4096×2160@60Hz 8-bit 4:4:4, 4096×2160@60Hz 10-bit 4:4:4, and 4096×2160@60Hz 12-bit 4:2:0 HDR
• Input Audio Port: 1 x SFP+ (10GBase-SR)
• Output Audio Port: 1 x HDMI
• Input/Output Audio Format Control: Supported audio formats at various frequencies

Frequently Asked Questions

• Q: What is the maximum distance supported for signal transmission?
  • A: The device supports point-to-point transmission of a 4K signal up to a distance of 300 meters.
• Q: Is the VLIP-SDFR-RX compatible with other SDVoE products?
  • A: Yes, the VLIP-SDFR-RX is compatible with all ProITAV SDVoE products.

Important Safety Instructions

FCC STATEMENT

Warnings of FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and decoder.
• Connect the equipment into an outlet on a circuit different from that to which the decoder is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Introduction

VLIP-SDFR-RX comes with the compact size and economical, flexible SDVoE solution. They allow uncompressed true 4K@60Hz video to be switched and distributed over standard 10GbE Ethernet networks with zero frame latency over 300 meters.

4K IP Delivery

Employed with IP protocol exchanging technology, the encoders can communicate with decoders via the switch to realize point (multipoint) to point (multipoint) matrix switching flexibly as required. Also, an encoder can connect to a decoder directly with an Ethernet cable, serving as an HDMI 2.0 extender set.

HDMI 2.0 and HDCP 2.2 Distribution with Zero Frame Latency

With HDMI 2.0 and HDCP 2.2 compliance, they support all HDMI 2.0 timing envelope of 594 MHz, e.g., 4K/60 8-bit 4:4:4, 4K/60 10-bit 4:2:2 and 4K/60 12-bit 4:2:0 (HDR). Light compression technology allows them to deliver video at lower compression ratios for keeping picture quality identical to the original source when the raw data exceeds the Ethernet bandwidth. Furthermore, the video is delivered with zero frame latency.

Compact design and Cost-Effective Solution

The compact size design is suitable for installation in tight space. Also, they are compatible with other SDVoE series products, providing a cost effective, flexible solution for system deployment.

Features

• Compact size and economical design
• HDMI 2.0 and HDCP 2.2 compliant
• Lossless distribution of most timing formats
• Light compression with the raw data rate exceeding 10Gb Ethernet bandwidth
• Supports input and output resolutions up to 4096×2160@60Hz 8-bit 4:4:4, 4096×2160@60Hz 10-bit 4:4:4 and 4096×2160@60Hz 12-bit 4:2:0 HDR
• Supports point-to-point transmission of 4K signal at the distance up to 300m
• Supports point-to-multipoint, multipoint-to-multipoint transmission via 10GbE switch at the distance of up to 300m (between a device and the switch)
• Zero-frame latency
• Compatible with all ProITAV SDVoE products
• Required bandwidth: 6~8 Gbps for 4K, 3.2 Gbps for 1080P
• Compatible with Semtech BlueRiver AV Manager

Package Contents

1. 1 x VLIP-SDFR-RX
2. 1 x 5VDC 2A Power Adapter (with US Pins)
3. 1 x Optical transceiver
4. 2 x Mounting Brackets (with Screws)

Specifications

Video

Input Video Port| 1 x SFP+ (10GBase-SR)
End-to-End Time Latency| Zero-frame latency
Output Video Port| 1 x HDMI
 | 640×4808, 800×6008, 1024×7688, 1280×10248, 1360×7688,
 | 1440×9008, 1440×10508, 1600×12008, 720×4807 (480i59),
 | 720×4807 (480p59), 720×5766 (576i50), 720×5766 (576p50),
 | 1280×7205 (720p50), 1280×7207 (720p59),
 | 1280×7208 (720p60), 1920×10806 (1080i50),
 | 1920×10807 (1080i59), 1920×10808 (1080i60),
 | 1920×10801 (1080p23), 1920×10802 (1080p24),

Input/Output Video Resolutions

| 1920×10803 (1080p25), 1920×10804 (1080p29),

1920×10805 (1080p30), 1920×10806 (1080p50),

1920×10807 (1080p59), 1920×10808 (1080p60),

 | 3840×21601 (2160p23), 3840×21602 (2160p24),
 | 3840×21603 (2160p25), 3840×21604 (2160p29),
 | 3840×21605 (2160p30), 3840×21608 (2160p60), 4096×21605,
 | 4096×2160⁸
 | ****

1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97 Hz,

 | 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz
Audio
Input Audio Port| 1 x SFP+ (10GBase-SR)
Output Audio Port| 1 x HDMI

Input/Output Audio Format

| LPCM, 2.0/5.1/7.1 channel, 44.1/48/96/192 kHz Dolby True HD, up to 7.1,192kHz

DTS-HD Master, up to 7.1,192kHz

Dolby Digital AC-3 (DVD format) DTS version 1 (DVD format)

Control
Control Method| Semtech BlueRiver AV Manager
Mechanical|
Transmission Distance| 300m with OM-3 multimode optical fiber cable
ESD Protection| Human body model:

• ±8kV (air-gap discharge)

• ±4kV (contact discharge)

---|---
Dimensions| 64mm x 22mm x 87mm (2.52″ x 0.87″ x 3.43″)
Weight| 0.35lb (0.16kg)
Power Supply| 5V 2 A DC
Power Consumption| 4.78W

Operating Temperature

| 32°F ~ 104°F (0°C ~ 40°C)

10% ~ 90%, non-condensing

Storage Temperature

| -4°F ~ 158°F (-20°C ~ 70°C)

10% ~ 90%, non-condensing

Operation Controls and Functions

1

| ****

SYSTEM LED

| • On: The device is connected to a display, but doesn’t receive any streams.

• Blinking quickly: The device is connected to a display and a 10G network, and is receiving streams.

• Blinking slowly: The device is connected to a 10G network but not connected to a display.

• Off: The device is connected to neither a display nor a network.

2| VIDEO LED| • On: Video signal is being transmitted to the connected display.

• Off: No video signal is transmitted.

3| HDMI| Connect to an HDMI display.
4| 10G FIBER| Connect to an optical fiber cable using the optical transceiver provided.

5

| ****

Reset Button (Recessed)

| Use a pointed stylus to press this button to restart or reset the device.

• Short press: To restart the device.

• Long press for more than 5 seconds: To reset the device to factory defaults.

Note: When you reset the device, your custom data is lost. Therefore, exercise caution in using this button.

6| 5V| Connect to the power adapter provided for DC 5V power input.

Installation

The device can be installed on a flat surface as the following:

1. Position and install the mounting brackets using the mounting screws provided.
2. Repeat above step for the other side of the device.
3. Attach the brackets to the desired location using screws (not included in the package).

Using BlueRiver AV Manager for Device

Control

The BlueRiver AV Manager is a simple intuitive software to manage and control SDVoE compatible endpoints and edge devices. For more information about obtaining the software, contact us

Installation

1. Before installation, ensure that your PC, TX, RX are on the same subnet.
2. Download and install the BlueRiver AV Manager file (*.exe) on your computer. After installation, the application GUI is accessed through a browser by simply entering the “127.0.0.1” or “localhost”.

Getting Started

• BlueRiver AV Manager includes three tools for managing and controlling the devices – Monitoring, Operate and Configure, which are accessed from the Home page.

Device Monitoring and Configuration

• The Monitoring tool is used to display device list and view device information, including details of device identity and capabilities, video and audio streams, device model in the original JSON format, network settings, etc.
• The Configure Tool is used to set and define device behavior and properties. It includes definition of devices alias name, initial configuration of IP address mode, video output mode, etc.
• Enter either Monitoring or Configure page, all devices are shown in device cards. To access device details or configuration, simply select a card.

Video Routing

• The Operate tool is for video routing between sources and displays. Endpoints connected to sources or displays are shown as device cards and form a routing grid where devices connected to sources appear on the grid vertical axis and devices connected to displays are shown horizontally.
• To route the video from a source to a display, simply press the intersection point between the two. To remove the route, just press the intersection point again.

Using AVP Product Updater for Firmware Upgrade

Before performing firmware upgrade, ensure that your PC, TX, RX are on the same subnet.

Getting Started

WARNING: DO NOT disconnect the device from its power supply and the network during the upgrade process.

1. Contact your supplier for the device’s latest firmware files – an AVP firmware file (*.apz) and a MCU firmware file, and the latest compressed AVPUpdater package file.
2. Extract the compressed AVPUpdater package file on your PC, and double click AVPUpdater.exe to launch the AVP Product Updater software.
3. A window opens as follows. Click Search in the Operation area to find the encoders and decoders.
   • Note: The AVP Product Updater is applicable to all IP6000 AVP products; while for a IP6000LASF series unit since its MCU doesn’t include a network port and is upgraded through a serial port, its “MCU MAC” and “MCU IP” are displayed as “”.
4. Select the desired devices for upgrade, and choose the correspondingAVP firmware and MCU firmware to upload in the AVP Firmware andMCU Firmware field. Click Update to Proceed.
5. The upgrade process takes about 1-2 minutes. A prompt of “MCUupdated successfully” appears after the upgrade is completed.

Application Diagram

HDMI 2.0 Extender

Features:

• 4K Video transmission
• Zero latency from end to end
• Maximum extension distance is 300m through an optical fiber cable.

IP-based HDMI 2.0 Splitter

Features:

• 4K Video transmission
• Zero latency from end to end
• Suitable for commercial point-to-multipoint applications, for example shopping malls and gymnasiums.

IP-based HDMI 2.0 Switcher

Features:

• 4K Video transmission
• Zero latency from end to end
• Multipoint-to-point matrix switching

IP-based HDMI 2.0 matrix

Features:

• 4K Video transmission
• Zero latency from end to end
• Multipoint-to-multipoint matrix switching

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>