VIKING BAGS 26L Painted Motorcycle Hard Saddlebags Installation Guide

VikingBags FAT Bracket Mounting
Installation Instruction:

26L Painted Motorcycle Hard Saddlebags

COMPLETE KIT INCLUDES:
i Saddlebags (Pair)
ii Mounting Kit (Package)
iii Model Specific Bolt Kit (Package)

A Pair of Saddlebags (Left – 1 gty and Right – 1 qty): Mounting Kit Parts:

Parts Diagram:

Model Specific Bolt Kit Parts:

Note:
i You may receive extra bolts and spacers; not all of them will be used. Please use the ones that match your bike’s fender bolt thread and length. If the bolt is too long, you can use more or thicker spacers.

Kit Diagram:

Tools Required:
i Adjustable Wrench
ii Socket Wrench
iii Combination Wrench
iv Drill
v Drill Bits
vi Screw Driver
vii Marker/ Chalk
viii Thread Locker
ix Ruler / Measuring Tape

Tools Diagram:

IMPORTANT
Before you start, inspect the bags and parts to make sure they are not damaged. Also, make sure you have all the mounting kit parts and bolt kit. Do not proceed if you are missing any parts. Please contact us about any missing parts and we will provide them for you.

COPYRIGHTOVIKING BAGS

Instructions:

Step 1:
Hold the bag against the fender to find a suitable position to mount it.
Note: Having a helper will make the positioning & marking process much easier.

IMPORTANT
Before you mark where to drill the holes, please make sure you have a minimum clearance space of 2 inches from other parts such as the exhaust, shocks, belt guard, turn signal, and axle nut. Sit on the bike to make sure there is that 2 inches of space after the shock compresses. You should also check if a passenger can sit and reach the passenger foot pegs comfortably.
Step 2:
Once the bag is in the desired position, hold the bag in place and mark the fender bolt positions on the back of the bag with marker/ chalk.
These points are where holes will be drilled and the mounting bolts inserted.

Step 3:
After marking the holes, lay the bag on a flat surface. Position the mounting bracket on the back of the bag until top bracket hole aligns with the top mark on the back of the bag, and the bottom of the bracket parallel to the bottom the bag. While holding the bracket in place, mark the position of the bottom hole in the bracket with marker/ chalk. Repeat the same process for the second mounting bracket. Step 4:
Drill the marked points where you plan to insert the mounting bolts.

Note:
Please make sure the drill bit size matches the size of the fender bolts for the top holes and also matching flip head bolt for the bottom. Do not drill the bag if you are missing parts or unsure about any of the installation steps.
Step 5:
With the brackets in place, insert the 8mm x 15mm flip head bolts with washers first through both of the two bottom holes in the back of the bag, and then through the bottom holes of both brackets from inside to outside, with the bolt heads staying inside the bag. Tighten the bottom bolts using the nuts and a wrench.
Note:
Please add thread locker on the nuts to keep all the bolts secure. Step 6:
The flat side of the bracket should be facing the back of the bag. Using 10mm flat washers, insert a Allen key head bolt from inside the bag through each of the two top holes and then through the bracket. Step 7:
Place the saddlebags against the fender and align the 2 fender bolts, then push the Allen key head bolts through the fender holes and tighten using a wrench.

Note :

• Please add thread locker on the nuts to secure your bolts.
• If the bolts are too long and risk hitting the tire, please use spacers. Insert the Allen key head bolts through spacers first before inserting them through the back of the bag and the brackets.
• If a bag is too close to shock or turn signals, you can add more spacers for more clearance.
• If a bag is too close to the chain guard or axle bolt, use the optional tilt control adapter (included).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>