beok-controls TRV603 Wi-Fi Smart Thermostatic Radiator Valve Owner’s Manual

Table of Contents

Wi-Fi Smart Thermostatic Radiator Valve

Automatic debugging function, suitable for all kinds of mainstream valves
The device supports Wi-Fi fast distribution network, no additional gateway is required
Intelligent PID algorithm, efficient control of valve opening and closing, energy saving and environmental protection
The motor adopts ultra-quiet technology to minimize noise pollution
The device has activated the automatic conversion of summer time and winter time, which can be activated or terminated as needed

Standard Accessories

Display Symbol

Press the battery compartment lock, remove
Initialize, the mandrel pulls back, then is displayed and blinking on the screen
When stop blinking, install the TRV union nut with M30*1.5 thread for heating valve, and then tighten the nut.
Attention : While inserting the batteries, please make sure the polarity of battery (+/-) is aligned.
Press the middle button and then ” Hat” start blinking, the device enter valve-adjusting process. After several minutes, the process is completed when initialized screen is displayed.

How to install the adapter correctly

Temperature control mode

Press the middle button to switch between Auto mode and Manual mode.

Auto mode

When is displayed on the screen, it is under Auto mode.
Four time periods and setting temperature could be programmed per day, one week as a cycle, based on customized needs.

Manual mode

When is not displayed on the screen, it is under Manual mode. The device will work according to current setting temperature, without controlled by the time period program.

Temporary mode

Under Auto mode, will be blinking after setting temperature, and then it will enter Temporary mode.
The device is switched to Manual mode temporarily, without controlled hu the time narind nraaram # will retum to Auto made hu nevt time norind

Attention : Only Manual mode is available when the device is not connected to Internet.

Stop heating and pause heating

ON : In summer, rotate the knob clockwise until “ On ” is displayed under manual mode to stop heating. At this time, the heating valve is fully open. This can extend the use life of valve.
OFF: In winter, rotate the knob counterclockwise until “ OF ” is displayed under manual mode to pause heating temporarily. At this time, the heating valve is closed and the frost protection is activater.

Open-window function and Anti-scale

Open-window function: First, enter the APP home page to turn on the window detection function, the device will automatically identify whether the window is open. When it is detected that there is cold wind, and the temperature drops by more than 1.5°C within 4.5 min, the open-window function will be activated. At this time, the screen displays “ OP “, and the temperature is set to 12 C.
Anti-scale: TRV executes routine decalcification every Monday at 12:00 to protect the valve from calcification. “[R” will be displayed on the screen during decalcification.

Attention : While the open-window function is activated, following operations will terminate it from taking effect.

Child lock function and Restore factory settings

Child lock function: Long press the middle button for 3 seconds until “24” is displayed on the screen to activate the child lock. While the device is locked, long press middle button for 3 seconds until “I ” disappear to deactivate the child lock.
Restore factory settings: Long press the middle button and insert the battery at the same time until ” Ff;” is displayed on the screen and blinking for 3 seconds, the device will be restored to factory settings and restarted.

Attention : Once the device is restored to factory settings, all previous settings can not be recovered.

APP remote control and voice control

Download Smart Life APP

Add device

Under manual mode, rotate the knob counterclockwise until “OF” is displayed. Then long press the middle button for 3 seconds until is blinking.
Enter the ” Home” interface of the APP, click in the upper right corner, select the “Add” button in the pop-up window, and finally click “ + ” to enter the Wi-Fi password interface;
Select 2.4G Wi-Fi and enter the password, click “Next”, and then wait for the connection to succeed.
After the addition is successtul, click “Next”, and the wifi smart thermostat has been added successfully.

Mode Selection