BEOK CONTROLS BOT-R7X Wireless Gas Boiler Heating Thermostat Instructions

BOT-R7X Wireless Gas Boiler Heating Thermostat

Application

Intelligent digital thermostat is a temperature controller suitable for floor heating systems. Through comparing ambient temperature and set temperature, it controls the working state of the electric valve of the floor heating system to adjust the ambienttemperature, which is comfort and energy saving.

Operating Instructions

ON/OFF key: Press the ON/OFF key to turn on and off once; Press shutdown again while closing all valves.
Mode switch key: In the power-on state, press to switch the working mode. The LCD indicates the manual mode and the display indicates the automatic mode.
Regulation key: In the startup state, press the button and the temperature will flash, then rotate the outer frame to adjust the temperature setting.
Clock adjustment: In the power on state, press and hold the button for 5 seconds. After the icon flashes, rotate the outer frame to adjust. Press the button to switch between time and week adjustments, and press the button to save and exit.
Lock key function: In the power on state, press and hold the button for 5 seconds to enter the lock button state on the panel.
A lock icon appears at the bottom of the display screen, indicating successful lock button locking

Low Temperature Protection Function

Advanced options enter the third option ON, the thermostat is in the shutdown state, when the indoor temperature is lower than 5 degrees, the thermostat automatically turns on heating. when the indoor temperature rises to 5 degrees, the thermostat automatically turns off heating.

Electrical Specification

1. Temperature sensor: NTC
2. Temperature precision: +0.5°C
3. Self- consumed: < 170uW
4. Voltage: 3pcs 1.5V batteries
5. Load current: 3A(negative)
6. Protection grade: IP20

Wiring Diagram

Remark:
N & L: 110~220Vac input
K1 & K2(dry contact): boiler / heater
N & NO: normally close (NC) actuator
N & NC: normally open (NO) actuator
N & M: Valve
Notes: since some circuits of this product involve strong electricity, which need to be installed by professionals.

Code Matching Process:

• Output indicator
• Code matching indicator
• Power indicator

1. Power on the receiving panel, the power indicator is long on.
   Press and hold the code matching button for 3 seconds, and the code matching indicator flashes.

2. Install three pieces AA batteries on the transmitting panel.
   In the POWER OFF state, press and hold the button for 5 seconds to check the code. When the code checking indicator light on the receiving panel remains on, the code checking is successful.

Programming Mode Operation

In the POWER ON state, press and hold the button for 5 seconds to enter programming mode. After entering programming mode, press the button to switch parameters, rotate the outer frame to adjust various parameters, press the button to adjust for minutes, and press the button to adjust the temperature. The adjustment method for the following time periods is the same as the first time period. Press the button to save and exit.

Frame
2| | 08:00| 16°C
3| | 11:30| 16°C
4| | 12:30| 16°C
5| | 17:00| 22°C
6| | 22:00| 16°C
Day Off| 1| | 08:00| 22°C
2| | 23:00| 16°C

Parameter Setting

In the POWER OFF state, long press the button for 5 seconds to enter the parameter setting interface. At this time, press the button to cycle through the selection of the parameters to be set, rotate the outer frame to adjust the parameters of each item, and press the button to save and exit.

Paramet
er Item| Parameter
Name| Default Value| Functional Meaning
---|---|---|---
1| Temperature compensation| 0| The temperature compensation
range: -9.9~9.9°C
2| Switch deviation setting| 1| The temperature difference start-up range is 0.5~10°C
3| The shutdown antifreeze function starts
and stops| ON| OFF: Turn off the antifreeze function
ON: Turn on antifreeze function
4| Rest day selection| 2| 0: Turn off programming
1: Take a day off
2: Two-day weekend
3: No rest
5| Set the upper limit of the temperature| 60°C| Set the upper temperature range from 15~95°C
6| Restore factory settings| —| Long press for 3 seconds, display “——_” to restore factory settings

Installation Method

1. Install an expansion screw sleeve with a spacing of 59mm on the wall.

2. Use a screwdriver to separate the upper cover and the lower cover, pursuant to the wire direction, pass the wire through the back cover to the wiring duct, and leave about 20cm long as per the actual situation.

3. Fix the bottom shell to the wall, and finally fix the wire, and cover the front shell on the bottom shell.

Inspection Steps
Install the intelligent touch screen thermostat in a place where it is easy for the user to view the screen and adjust the temperature set point. The thermostat is located in a place that can represent the overall ambient temperature of the room. Avoid installing the thermostat near hot and cold sources, such as vents, heaters, outdoors, etc.

Common Faults Handing

2. Inspect whether the boot key is valid LCD displays.
LCD displays messy code| Whether the rear shell installation is deformed, it can be loosened and reinstalled.
Display is normal, but there
is no output| 1. Check whether the boundary between the main control board
and the power board is damaged.
2. Check whether the output is connected to the wrong wire.
Temperature displays error| Calibrate the panel temperature display via the first item of advanced options.

WiFi Connection

Smart Life App Download
For IOS system: Login in App Store, search “ Smart Life “or ” Tuya Smart”, you can download it on your iphone.
For Android System: Login in Google Play, search“Smart Life”, or ” Tuya Smart” ,you can download it on your phone.
Or scan below code to download:

https://smartapp.tuya.com/smartlife

Thermostat Setting

In the POWER OFF state, press and hold the button for 5 seconds. When the WIFI icon is displayed on the screen, you can start the configure on your phone.
Connection with phone
Open”Smart Life “or“Tuya Smart” on your phone.
Be sure to turn on your phone’ s Bluetooth.
Only 2 4G status configuration can be added for WIFI access on mobile phones (the name and password can only use numbers and letters, not symbols),

Click the Add Device button in the upper right corner, or click Add Device.

Enter the WIFI password, click Next.

Wait 1-2 minutes for the device to connect. If no, check the mobile phone, route, thermostat, and network device.

After the configuration is completed, the WiFi icon of the thermostat does not flash.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>