BEOK CONTROLS TDR89 ZIGBEE Thermostat User Guide
- August 2, 2024
- BEOK CONTROLS
Table of Contents
BEOK CONTROLS TDR89 ZIGBEE Thermostat
THIS THERMOSTAT IS SUITABLE FOR WATER HEATING, ELECTRIC HEATING AND GAS BOILER
Welcome
Thank you for your trust and support. By adopting higher-end technology and
more perfect technology, your new thermostat will provide you with the right
temperature environment every day in the future, making your life more
comfortable and your living environment more stylish and beautiful. For
detailed instructions on the installation and use of this thermostat, please
read this manual carefully. Please contact a professional to install the
thermostat for you and install and use the product to the extent permitted by
law.
Application
Intelligent digital temperature controller is a floor heating system suitable
for room temperature control and household temperature control. It controls
the operating state of the floor heating equipment by comparing the ambient
temperature with the set temperature, which improves comfort and achieves
energy saving. This digital temperature controller adopts microcomputer
control technology and is equipped with full-screen display touch buttons,
which is elegant in design and easy to use. The thermostat has manual
automatic, programmable and state memory functions.
Product packaging
- Thermostat host 1 PC
- Qualification certificate 1 PC
- Sensing line (optional) 1 PC
- Manual 1 PC
- Screw 2 PCS
Product Model
- WP Plumbing 3A
- EP Electric Heating 16A
- WPB linkage, gas boiler 3A
User Notes
- Please read this manual carefully. Improper operation may damage the product or cause dangerous conditions.
- The installation personnel must be well-trained and experienced service technicians.
- After installation, please read this manual carefully and operate the product according to the instructions.
Caution : Risk of electric shock or equipment damage.
Wiring Diagram
Note: WP for water heating; EP for electric heating; WPB for gas boiler
Installation procedure
This product is installed with a standard 86 control switch (in compliance with European regulations).
- Connect the power box according to the wiring diagram.
- Separate the power supply from the control board cable.
- Screw the power supply into the box of 86.
- Connect the power board to the control board line, and align the buckle at 30 degrees to complete the installation.
Description of display & Icon
Operating Instruction
- Power on/off: press to turn on/off the thermostat.
- Press the key to switch between manual and automatic modes.
- In the automatic mode, press + or – to adjust the temperature to enter the automatic temporary mode. This mode runs for only one session.
- Press key to enter the clock setting, press the mode key to switch settings options, and press the + and – keys to adjust the value of each parameter.
- Simultaneously press and hold the + and – keys for 5 seconds to add or cancel the child lock.
- WIFI link: When the thermostat is turned on, press and hold the + button for five or eight seconds, the WIFI icon flashes on the thermostat display, and the thermostat enters the code matching state.
Time programming instructions
Long press the key to enter the programming setting, short press the key to
switch options, press the + or – key to adjust the parameters of each option,
and press the key to exit and save mode.
Advanced options
In the shutdown state, press the key and key. Press for 5 seconds to enter the
advanced option settings. Press the key to enter the next option, then press
the + and – key to adjust options, and press the key to exit the advanced
option setting mode.
| Display Code | Function | Setting And Options | Factory Defaults |
|---|---|---|---|
| 01 | Temperature calibration | -9.9-9.9℃ | -2℃ |
02
|
Sensor selection
| IN:Use the internal sensor OUT:Use the external sensor
ALL: Use both internal and external sensors.
|
IN
03
| Measured temperature extreme value
Modification
|
35-60℃
|
60℃
04| Temperature hysteresis| 0.5-10℃| 1℃
05| Antifreeze function| OFF:Close anti-frozen ON:Open anti-frozen| OFF
06
| Weekly programming mode setting| 7: 7 working days
6: 6 working day+1 rest day
5: 5 working day+2 rest day OFF: turn off programming
|
5
07
| Main and auxiliary reverse
selection
|
00:close the main and auxiliary reversal 01:auxiliary reversal
|
00
08
|
Backlight brightness
| 00：turn off the backlight 01：low brightness 02：medium brightness
03：high brightness
|
03
09| Set temperature
upper limit
|
15-95℃
|
60
10
| Restore factory defaults| long press + button to adjust the
display “—”, press button to restore the factory settings
|
–
11| Sound| ON: turn on the sound OFF: turn off the sound| ON
About wireless connection
Before using the wireless thermostat for the first time, you should set the
signal and configuration through your smart phone or tablet to allow
communication between your connected devices.
WIFI connection: When the thermostat is turned on, press and hold the + button
for 5 seconds, the WIFI icon flashes on the thermostat display, and the
thermostat enters the code matching state.
-
Download the APP
Search for “Tuya” in App market or scan below QR Code to download -
Register Account
If you don’t have an APP account yet, you can choose to register or log in via SMS verification code. Click “Create a new account”, you will enter the Tuya Smart Platform Privacy Policy page. After you click Agree, you will officially enter the mobile phone registration page. The system automatically determines the current country/region. You can also select the country/region manually. After entering your mobile phone number or email address, click “get verification code” . Enter the received verification code, then enter the password, and click “finish” to register successfully. -
Add gateway device
Click “Add Device” or “+”on the top right of the APP homepage, and enter the “Add Device” interface. -
Thermostat add
-
Display of temperature controller APP interface
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>