CHIEF RFCUB Carrello Standard Vesa Max 800×600 Con Mensola User Guide
- August 23, 2024
- Chief
Table of Contents
CHIEF RFCUB Carrello Standard Vesa Max 800×600 Con Mensola
Quick Setup
- For complete installation instructions, refer to the
- Installation Manual included with this product.
- This Quick Setup Guide is meant to provide only an overview of the various installation steps.
- ALWAYS read the Installation Instructions in its entirety before beginning the Installation.
Tools Required for Installation
INSTALLATION INSTRUCTION
STEP 01
- Assemble The Base
- Assemble the right leg assembly (J) and left leg assembly (N) to the crossbar (L) using two 5/16-18 x 4-1/4″ screws (Q) through one crossbar end cap (K) per leg. (See Figure 1)
STEP 02
- Attach The Lower Column To The Base
- Attach the lower column (G) to the crossbar (L) using four 5/16-18 x 2-1/4″ screws (R) and 5/16″ washers (U). (See Figure 2)
STEP 03
- Attach The Face Plate To The Top Column
- Install the face plate assembly (A) to the upper column (H) in one of three positions using one connector – stud (E), one connector – no stud (F), and four 5/16-18 flange nuts (W). (See Figure 3)
STEP 04
- Attach The Upper Column To The Lower Column
- Attach the upper column (H) to the lower column (G) using four 10-24 x 1/2″ flat head screws (P). (See Figure 4)
ATTACHING DISPLAY
WARNING: IMPROPER INSTALLATION (A) CAN LEAD TO MOUNT FALLING OR CAUSING
SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT SUBSTITUTE HARDWARE.
ONLY USE HARDWARE PROVIDED OR SPECIFIED BY MANUFACTURER.
STEP 5A
For displays with larger than 400 × 400 VESA, use the included interface
brackets before attaching to the face plate.
STEP 5B – OPTIONAL
For displays with 400 x 400 VESA or smaller, mount directly to the face plate.
Mount your display with larger than 400 × 400 VESA using the included interface to the face plate
- Partially install two 5/16-18 x 5/8″ screws (S) into the upper horizontal interface (C). (See Figure 6)
- While supporting both sides of display, align two 5/16-18 x 5/8″ screws (S) installed in upper horizontal interface (C) with two mounting holes in the face plate assembly (A). (See Figure 7)
- Install two 5/16-18 x 5/8″ screws (S) through the face plate assembly (A) into the lower horizontal interface (C). (See Figure 8)
- Tighten two 5/16-18 x 5/8″ screws (S) in upper horizontal interface. (See Figure 8)
STEP 5B – OPITIONAL
Mount your display with 400 x 400 or smaller VESA pattern directly to the face
plate
- Select correct screws, nesting spacers (if necessary), and universal washers (if required) from the hardware bag (AA-AH) and attach display to two upper mounting slots in face plate assembly (A). (See Figure 9)
- Tighten four screws (AA-AF) in upper and lower mounting slots in face plate assembly (A). (See Figure 10)
BONUS STEP!
- Attach the included shelf to store accessories like keyboards, laptops, and styluses
- The shelf assembly (B) can be installed in four different positions to achieve the desired height. (See Figure 11)
- To lower column (G) using one connector – stud (E) and two 5/16-18 flange nuts (W).
INSTALLER INSPIRED legrandav.com
- USA 866.977.3901 av.chief.support@legrand.com
- CANADA 877.345.4329 av.chief.canada@legrand.com
- EMEA +31 495 580 840 av.emea.sales@legrand.com
- APAC +852 2145 4099 av.asia.sales@legrand.com
©2023 Legrand AV Inc. 230867 Rev A 11/23 Chief is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All patents are protected under existing designations. Other patents pending.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>