MegaSys NF06045 Outdoor Powered Professional Audio Class D Active Pa Speaker System User Manual

MegaSys NF06045 Outdoor Powered Professional Audio Class D Active Pa

Speaker System

Specifications

• MegaSys 1
• Frequency Response: 3.5 2-WAY Passive Crossover Speaker System
• Total Amplifier Power: 180W Continuous, 360W Program, 720W Peak
• Maximum SPL@1M: 150Hz-20kHz
• Crossover Frequency: 8 ohms
• Dimensions(WxHxD): 430 x 630 x 610mm (16.93” x 24.80” x 24.02”)
• Net Weight: 35 Kg (73.85 Ibs)

Product Usage Instructions

Quick Start

1. Turn off all equipment.
2. Ensure main volume controls are turned down.

Connection Plate System

1. Make initial connections with equipment powered off.
2. Connect signal cable from mixer to left/right output.

BT Control

1. Download Sound Control DSP APP from the APP store.
2. Turn on MegaSys 1 power switch.
3. Turn on Bluetooth device on phone or iPad.
4. Open Sound Control APP and connect to MegaSys 1.

FAQ

• Q:How do I pair the music source using BT Pair Connection button?
  A: Simply click the BT Pair Connection button once to pair the music source.

• Q: What is the purpose of the BT TWS Connection button?
  A: The BT TWS Connection button is used for TWS connection by double-clicking it.

Important Safety Instructions

TO REDUCE THE RISK OF ELECTRIC SHOCK PLEASE DO NOT REMOVE THE COVER OR THE BACK PANEL OF THIS EQUIPMENT. THERE ARE NO PARTS NEEDED BY USER INSIDE THE EQUIPMENT. FOR SERVICE, PLEASE CONTACT QUALIFIED SERVICE CENTERS.

• This symbol, wherever used, alerts you to the resence of un-insulated and dangerous voltages in the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death.
• This symbol, wherever used, alerts you to important operating and maintenance instructions. Please read.
• Protective Ground Terminall
• AC mains (Alternating Current)
• Hazardous Live Terminal
• ON Denotes the product is turned on.
• OFF Denotes the product is turned off.

CAUTION
Describes precautions that should be observed to prevent damage to the product.

1. Read this Manual carefully before operation.

2. Keep this Manual in a safe place.

3. Be aware of all wamings reported with this symbol.

4. Keep this Equipment away from water and moisture.

5. Clean it only with dry doth. Do not use solvent or other chemicals.

6.  Do not damp or cover any cooling opening. Install the equipment only in accordance with the Manufactu- rer’s instructions.

7. Power Cords are designed for your safety. Do not remove Ground connections! If the plug does not fit your AC outlet, seek advice from a qualified electrician. Protect the power cord and plug from any physical stress to avoid risk of electric shock. Do ot place heavy objects on the power. This could cause electric shodk or fire.

8. Unplug this equipment when unused for long periods of time or during a storm.

9. Refer all service to qualified service personnel only. Do not perform any servicing other than those instructions contained within the User’s Manual.

10. To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder.
    WARNING
    To reduce the risk of electric shock and fire, do not expose this equipment to moisture or rain.
    Dispose of this product should not be placed in municipal waste and should be separate collection. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet.

11. Move this Equipment only with a cart, stand, tripod, or bracket, specified by the manufacturer, or sold with the Equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid possible injury from tip-over.

12. . Permanent hearing loss may be caused by exposure to extremely high noise levels. The US. The government’s Occupational Safety and Health Administration (OSHA) has specified the permissible exposure to noise level. These are shown in the following chart:

According to OSHA, an exposure to high SPL in excess of these limits may result in the loss of heat. To avoid the potential damage of heat, it is recommended that Personnel exposed to equipment capable of generating high SPL use hearing protection while such equipment is under operation. The apparatus shall be connected to a mains socket outlet with a protective earthing connection.
The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

EMI CLASSIFICATION
According to the standards EN 55032 and EN 55035 this equipment is designed and suitable to operate in class B electromagnetic environments.

FCC CLASS B STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,and
2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties. For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the loudspeakers outdoor avoid spots exposed to bad weather conditions. Contact TOPP PRO for accessories to be used with speakers. TOPP PRO will not accept any responsibility for damages caused by inappropriate accessories or additional devices. Features, specification and appearance af products are subject to change without notice. TOPP PRO reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously manufactured.

Introduction

The new cabinets have been designed to provide a cost effective high grade solution while maintainig high quality cabinet construction and optimum components. Our Professional Audio Products are designed and tested by a highly qualified engineering team with more than 20 years of experience. Great care is placed in delivering products with excellent performance, specifications and dependable reliability. Also great emphasis is placed in creating and bringing to market products that can fill multiple applications and also offer customers exceptional value. Every audio product is strictly tested and complied to very strict standards.

Features

• Output Power: Subwoofer – 1000W Continuous/2000W Program/4000W Peak Class D @ 8 Ohms. Satellite – 500W+500W Continuous/2000W Program/4000W Peak Class D @ 8 Ohms.
• Connections: Input: 1 x Combo-XLR&1/4”, Output: 1 x XLR Thru&Mixout.
• Stereo Bluetooth Pair and TWS Connection Switch and Led Indicator (APP Control).
• Electronic Protections: Over heat Protection/Short Circuit Protection/Digital Compressor.
• Enclosure Construction: Plywood Cabinet,Resistant Black Paint, Metal Grille with Foam, Rubber Feet, Integrated side handles.
• Power Supply: 110V-240V~ 50/60Hz.

Useful Data
Please write your serial number here for future reference.

• Serial Number:
• Date of Purchase:
• Purchased at:

Quick Start

When mounting a speaker onto any stand, always ensure that the stand is on a flat, level surface, with the legs fully extended. Be sure to check that the maximum load weight for the stands is greater than the weight of the ARRAY SYSTEMS loudspeaker. Never use a stand with a maximum load weight lower than the speaker. Do not attempt to mout more than one speaker on a stand at one time.
The ARRAY SYSTEMS loudspeakers are heavy. It is recommended that a second person to help place the cabinet on a stand.
When the speaker is placed on a stand, always check the integrity and center of gravity of the system If the speaker can be tipped easily, or the pole is swaying, it is recommended that you lower the height of the stand. Position the stand and route cables so that the performers and the audience cannot tip over or trip on the system.

1. Place the MegaSys 1 SUB on a flat surface.
2.  Push the SAT from front to back into the SUB connector until it is tight.
3. After the installation is completed, if you need to disassemble, press the “LOCK” button of the SUB connector and push the SAT forward slowly.

Back Panel Description

1. Bi-Polar Main Power Switch.
2. AC Power.
3. Output.
4. Input Sensitivity”Switch for Line/MIC.
5. BT Pair Connection button; (One Click it to Pair Music Source).
6. BT TWS Connection button; (Double Clicks for TWS Connection).
7. BT Volume Control.
8. Main Volume Control.
9. Signal/Limit, Red Led, indicate on Status.
10. Power, Green Led, indicate on Status.
11. SUB Volume Control.

Connection Plate System

Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down.
Two Active Subwoofers & Two Passive Satellite Speakers

1. Connect one side of the signal cable to the output of your mixer (left / right) with a TRS or XLR connector and the other side of the cable to the line input (combo) in the active subwoofer (with a TRS to XLR connector). Then connect the speakon cable from the output of power in the Subwoofer to the satellites input.
2. Complete other connections as illustrated.
3. Turn on your mixer first, then the stereo power amplifier.
4. Turn up the volume controls of your amplifier to about 70%.
5. Use PFL function to get the proper input level for the mixer, and adjust the Mian Mix Level control to manipulate the output level.
6. After using, turn off your stereo power amplifier first, then the mixer.

BT Control

BT PAIR: Paired to one speaker

1. One click the”PAIR”button on the master speaker,You will hear a beep (boom), then the blue starts to flash. which means to enter pairing state.
2. Turn on the Bluetooth function on the audio device, search and select “MegaSys 1” to start pairing; (iPhone, iPad, Bluetooth adapter and other audio devices, no pairing password is required).
3. After about 20-100 seconds, the pairing will be completed. Once paired sucessfuly between source device and product, the blue will solid light, if pair failed, Please repeat above steps 1-3 to try pairing again.
4. Music playback
   *Bluetooth memory function: After the unit reboot, the system will proceed the automatic pairing based on the last memory.

BT TWS: Interconnection between two of the same speakers
Remark: If the speaker connected to your source device is the master, The other speaker linked with it will the Slave.
The sound signal will be sent to the master from source device, if the master speaker linked with the Slave speaker. then it playback on the left channel of the master and on the right channel of the Slave, Finally realize the left/right channel stereo effects.

1. Select one of two linked speaker as the master.
2. One click the PAIR button on the master, You will hear a beep (boom), then the blue starts to flash, which means to enter pairing state.
3. Open the BT function on audio device, Then search and select “MegaSys 1” to start pairing (iPhone, iPad, Bluetooth adapter and other audio devices, no pairing password is required).
4. After about 20-100 seconds, the pairing will be completed. Once paired sucessfuly between source device and product, the blue will solid light, if pair failed, Please repeat above steps 1-3 to try pairing again.
5. Separately Double clicks the LINK button on the master and the Slave, you will keep hear a beep (boom) and keep 20-100 seconds.
6.  Once the master paired to the Slave sucessfully, the beep(boom) will disappear and the BT indicatior will light solid blue.
7. Play music.

BT Control
BT CONTROL APP

1. Please download the “Sound Control DSP” APP from the APP store.
   There are IOS and Android versions for selection.

2. Turn on the power switch of the MegaSys 1 product

3. Turn on the Bluetooth device on your phone or iPad, and then open the “Sound Control” APP

4. Click Refresh, click the selected model in the product model list that appears, and then click “Connect” to enter the control interface, as shown in the figure below

Wire Connections
Either the 1/4″ TRS phone jack or XLR connector can be wired in balanced and unbalanced modes, which will be determined by the actual application status, please wire your system as the following wiring examples:

In-line Connection
For these applications the unit provides 1/4″ TRS and XLR connectors to easily interface with most professional audio devices. Follow the configuration examples below for your particular connection:

Technical Specifications

Megasys 1

Frequency Response

|
---|---
40Hz – 20KHz (-10dB)
Total Amplifier Power| 2000W Continuous/4000W Program/8000W Peak Class D
Maximum SPL@1M| 134dB
Crossover Frequency| 220Hz
Dispersion(-6dB)| 120°Horizontal
Dimensions(WxHxD)| 430 x 2170 x 610mm (16.93” x 85.43” x 24.02”)
Net Weight| 48 Kg (105.8 Ibs)
Megasys 1 SUB|
System Type| 15″ Active Subwoofer Speaker Cabinet
Frequency Response(-6dB)| 40Hz – 210Hz
Total Amplifier Power| 2000W Continuous/4000W Program/8000W Peak Class D @ 8 Ohms
Amplifier, Subwoofer| 1000W Continuous/2000W Program/4000W Peak Class D @ 8 Ohms
Amplifier, Satellite| 500W+500W Continuous/2000W Program/4000W Peak Class D @ 8 Ohms
Electronic Protections| Over heat Protection/Short Circuit Protection/Digital Compressor
Connections| Input: 1 x Combo-XLR&1/4”, Output: 1 x XLR Thru&Mixout
External Controls| MASTER Volume / SUB Volume / Power/Signal/Limiter/Protect Led Indicator / Bluetooth Pair and TWS Connection Switch and Led Indicator
Power Supply| 110V-240V ~50/60Hz
Enclosure Construction| Plywood Cabinet,Resistant Black Paint, Metal Grille with Foam, Rubber Feet, Integrated side handles
Mounting| Smart Mounting and Connection
Dimensions(WxHxD)| 430 x 630 x 610mm (16.93” x 24.80” x 24.02”)
Net Weight| 35 Kg (73.85 Ibs)
Megasys 1 TP|
System Type| 3.5″ 2-WAY Passive Crossover Speaker System
Output Power| 180W Continuous, 360W Program, 720W Peak
Frequency Response(-6dB)| 150Hz-20kHz
Impedance| 8 ohms
Transducer MID| 6 x 3.5” Woofer , 1.0” (25.4mm) Voice Coil
Transducer Treble| 5 x 1”Neodymium Driver, 1.0” (25.4mm) Voice Coil
Connector| 4 PIN Smart Mounting and Connection
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Dimensions(WxHxD)| 103 x 890 x 130mm(4.05” x 35.03” x 5.11”)
Net Weight| 7.2Kg (15.9 Ibs)
Megasys 1 BM|
System Type| 3.5″ Passive Full Range Speaker System
Output Power| 180W Continuous, 360W Program, 720W Peak
Frequency Response(-6dB)| 150Hz-20kHz
Impedance| 8 ohms
Transducer MID| 6 x 3.5” Woofer , 1.0” (25.4mm) Voice Coil
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Connector| 4 PIN Smart Mounting and Connection
Dimensions(WxHxD)| 103 x 650 x 130mm(4.05” x 25.59” x 5.11”)
Net Weight| 5.9Kg (13.0 Ibs)
|

Guarantee
Topp Pro guarantees the normal operation of the product against any defect of manufacture and / or vice of material, by the term of (12) months, counted as of the date of purchase on the part of the user, committing itself to repair or to change, to its election, without position some, any piece or component that will fail in normal conditions of use within the mentioned period. This guarantee is valid if the original buyer will have to present/display this certificate properly sealed and signed by the selling house, accompanied by the corresponding invoice of purchase where it consisted the model and serial number of the acquired equipment.

The guarantee does not cover:

• Damages caused by the illegal use of the product, repair and/or nonauthorized modification conducted by people by Topp Pro
• Damages caused by the connection of the equipment to other equipment different from the specified ones in the manual of use, or by bad connection to these last ones.
• Damages caused by electrical storms, blows and/or incorrect transport. – Damages caused by excesses or falls of tension in the network or by connection to networks with a tension different from the required one by the unit.
• Damages caused by the presence of sand, acid of batteries, water, or any strange element inside the equipment.
• Deteriorations produced by the course of the time, use and/or normal wear of the unit. – Alteration or absence of the serial number of factory of the equipment.
• The repairs could only be carried out the authorized technical service by Topp Pro, that will inform about the term and other details into the repairs to take place according to this guarantee. Topp Pro, will repair this unit in counted a term nongreater to 30 days as of the date of entrance of the unit to the Technical Service. In those cases in that due to the particularitity of the spare part, outside necessary their import, the repair time and the viability of the same one will be subject to the effective norms for the import of parts, in which case one will inquire to the user about the term and possibility into repair. With the object of its correct operation, and of the validity of this one guarantee, this product will have to be installed and to be used according to the instructions that are detailed in the manual associate or the package of the product. This unit will be able to appear for its repair, next to the invoice of purchase (or any other proof where the date of purchase consists), to its authorized distributer Topp Pro or an authorized technical center on watch by Topp Pro.

Exclusion of damages

• THE RESPONSIBILITY OF TOPP PRO BY ANY DEFECTIVE PRODUCT IS LIMITED THE REPAIR OR THE REPLACEMENT OF HE HIMSELF,

TO TOPP OPTION PRO. IF WE CHOSE TO REPLACE THE PRODUCT, THE REPLACEMENT CAN BE A RECONDITIONATED UNIT. TOPP PRO WILL NOT BE RESPONSIBLE BY THE DAMAGES BASED ON THE LOST, INCONVENIENCE, LOSS OF USE, BENEFITS, LOST SAVINGS, BY THE DAMAGE TO OTHER EQUIPMENT OR OTHER ARTICLES IN THE USE SITE, OR BY ANY OTHER DAMAGE IF HE IS FORTUITOUS, CONSEQUENT OR OF ANOTHER TYPE, ALTHOUGH TOPP PRO HAS BEEN NOTICED OF THE POSSIBILITY OF SUCH DAMAGES.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>