SuperHandy GUT168 Electric Floor Lift Standing Mobility Aid Instruction Manual
- August 19, 2024
- SuperHandy
Table of Contents
SuperHandy GUT168 Electric Floor Lift Standing Mobility Aid
Technical Specifications
- SKU#: GUT168
- Working Load Capacity: 440 lbs (200 kgs)
- Lifting Height (Above Ground): 1.2~28.7 inches (30~730 mm)
- Lifting Speed: 0.4 in/s (10 mm/s)
- Rated Voltage: 24V
- Stroke: 0~27.6 inches (0~700 mm)
- Duty Cycle: 2 min on 18 min off (max. 10%)
- Max Load: 3000N
- Max Output Voltage: 25.9V
- Max Output Current: 5A
- Input Voltage Capacity: 24~30V 2000mAh
- Input Output Power Adapter (Charger): 100~240V, 50/60Hz 1.5A, 29V, 2A
Product Usage Instructions
Safety Instructions
Prior to operating the floor lift, ensure the user meets suitability
criteria based on weight, size, mental capacity, and joint movement. Do not
use the floor lift if the user is unsuitable.
WARNING
- The maximum weight capacity is 440 lbs (200 kgs).
- Sit steadily on the floor lift and ensure a safe surrounding area.
- Avoid using on excessively sloped surfaces or surfaces with steps.
- Do not stand on the floor lift.
- Do not use if any parts are missing.
- Keep children away from the equipment.
- Avoid placing in overly hot areas due to batteries.
- If not in use for an extended period, fully charge the battery before storing.
Assembly
Left & Right Base
Align the mounting holes of the main body with the bases and secure with
M8x20 bolts from top to bottom and back to front.
Wired Remote Connector
Connect the wire remote to the actuator wire connector and place it on the
main body through magnetic attraction.
Seat Assembly
Raise the floor lift using the wired remote, insert the seat assembly tubes
into the floor lift tubes, align holes, and secure with D-type pins.
Frequently Asked Questions (FAQ)
-
Q: Can this floor lift be used on sloped surfaces?
A: It is recommended not to use the floor lift on surfaces with slopes exceeding 3 degrees for safety reasons. -
Q: How often should the battery be charged when not in use?
A: If the floor lift will not be used for an extended period, it is advised to fully charge the battery before storing to prolong its life.
440Lbs Floor Lift l GUT168 Operator’s Manual
Warning: Please read and thoroughly understand all instructions before operating. Failure to follow safety rules and other basic safety precautions may result in serious personal injury. Keep these instructions in a safe and easily accessible place so that they can be referred to when needed. Retain these instructions to assist in future servicing.
SAFETY INSTRUCTION
Prior to operating the floor lift, evaluate whether the user is appropriate for the device by considering aspects like weight, size, mental capacity, and joint movement. It’s essential to ensure that individuals who are not suitable do not use the floor lift. Persons with disabilities should either have assistance nearby or be within reach of alarm devices during use.
WARNING
- The maximum weight capacity of the floor lift is 440Lbs (200kgs).
- Please sit steadily on the floor lift and ensure the surrounding area is safe before use.
- Do not use the floor lift on excessively sloped surfaces (more than 3 degrees) or on surfaces with steps.
- Do not stand on the floor lift.
- Do not use if any parts are missing.
- Do not allow children to use this equipment.
- Do not place the floor lift in overly hot areas, as it contains batteries.
- When not in use for a long time, fully charge the battery before storing to prolong its life.
TECHNICAL SPECIFICATIONS
| SKU# | GUT168 |
|---|---|
| Working Load Capacity | 440Lbs. (200Kgs) |
| Lifting Height (Above Ground) | 1.2~28.7in (30~730mm) |
| Lifting Speed | 0.4in/s (10mm/s) |
Linear Actuator
Rated Voltage| 24V
Stroke| 0~27.6in (0~700mm)
Duty Cycle| 2min on 18min off (max.10%)
Max. Load| 3000N
Battery
Max. Output Voltage| 25.9V
Max. Output Current| 5A
Input Voltage| 24~30V
Capacity| 2000mAh
Power Adapter (Charger)
Input| 100~240V, 50/60Hz，1.5A
Output| 29V, 2A
KNOW YOUR MACHINE
CONTENTS SUPPLIED
The floor lift comes partially assembled and is shipped in carefully packed
carton. After all the parts have been removed from the carton, you should
have:
ASSEMBLY
Left & Right Base (See Fig. 1)
Align the mounting holes of the main body of the floor lift with the left and
right bases, and use 8 M8x20 bolts to fasten the main body to the bases from
top to bottom. Secure with 2 M8x20 bolts from back to front.
Wired Remote Connector (See Fig.2)
Connect the connector of the wire remote to the connector of the actuator wire
as shown in the figure below.
After the connecting, you can place the wired remote on the main body. It will adhere to the surface through magnetic attraction, ensuring that you don’t lose the control handle and can easily pick it up and place it back. Just like shown in the figure below. (See Fig.3)
Seat
Press the upward button on the wired remote to raise the floor lift by about 10
inches. Then, place the wired remote back. Now, we can insert the two square
tubes of the seat assembly into the square tubes of the floor lift. Align their
mounting holes and insert a D-type pin into the holes to secure them in place.
(See Fig.4)
Safety Belt (See Fig.5 & 6)
Lock the safety belt’s snap hook onto the belt anchor point, just like in the
following Figures.
OPERATION
Dual Power Mode.
This Floor lift features two power supply modes. When the battery is charged,
it can be used directly as described below. In the event of a depleted
battery, the power adapter (which also serves as a charger) can be connected
to an AC power source for immediate use. The usage procedure remains identical
to that when the battery is fully charged.
Pre-check.
Evaluate whether the user is suitable for the device by considering aspects
such as weight, body size, psychological capacity, and joint mobility. Press
the up/down button on the remote to ensure the chair automatically tilts
backward and confirm that the chair is rising/lowering normally.
Unbuckle your seat belt. (See Fig.7)
Before the user being lifted moves onto the seat, the safety belt must first be
unbuckled, and then the person can be moved onto
the seat.
Fasten the safety belt. (See Fig.8)
After the user has moved onto the seat, it is necessary to lock the safety
belt buckle, adjust the length of the safety belt, and ensure that the user is
sitting stably on the seat.
Lifting or Lowering. (See Fig.9)
Hold the up (or down) button on the wired remote, and the user will be lifted
(or lowered) to the appropriate position. Releasing the button will stop the
ascent (descent).
Status indicator
- Flashing green light: When the up or down button is pressed, the light flashing green, indicating that it is ascending or descending.
- Flashing red light: Indicates that the battery is low and needs to be charged for future use. (In emergency situations, if the battery is insufficient, the device can be directly connected to an AC power supply (100~240V, 50/60Hz) for operation)
Note: The maximum travel distance for lifting or lowering is 27.6in (700mm). When the seat is at its highest position, holding the up button will not allow it to rise further; similarly, when the seat is at its lowest position, holding the down button will not allow it to descend further.
Battery Charging. (See Fig.10)
When the status indicator on the wired remote flashes red, it indicates that
the battery needs to be charged. Connect the charger (power adapter) to an AC
power source (100~240V, 50/60Hz), the AC power indicator on the charger will
turn green, signifying that the charger is now working. During normal
charging, the battery charging indicator on the battery pack will turn red,
and it will change to green when the battery is fully charged. The charging
process typically takes about 4 hours.
MAINTENANCE & STORAGE
- The floor lift does not require regular maintenance. Keeping the battery charged helps to extend its lifespan.
- Although the floor lift is very durable and functions well both indoors and outdoors, it is recommended to store it indoors when not in use.
WARRANTY
Warranty covers twelve (12) months for workmanship of the product, except for wearing parts. Warranty period starts from the product purchase date. Warranty covers material quality and workmanship only. Warranty does not cover product for issues caused by improper usage or any operation not in accordance with the specifications of this manual. Any modification or tampering with the product in any way voids the warranty.
Thank you for your most recent purchase.
Great Circle USA
Support Line: 1-866-493-0524
help@greatcircleus.com
www.superhandyus.com
Follow us on social media @SuperHandy
Size: 145x210mm
REV 01/10/24
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>