REALTEK RTL8852BE Combo Module User Manual
- August 16, 2024
- Realtek
Table of Contents
RTL8852BE Combo Module
“`html
Product Specifications
-
Model: RTL8852BE Combo module
-
Manufacturer: Realtek Semiconductor Corp.
-
Date: Preliminary Version 2021/05/13
-
Operating Relative Humidity: 5-90%
(non-condensing) -
Storage Temperature: Relevant Humidity
-
MTBF Calculation: Over 150,000 hours
Product Usage Instructions
Environmental Information
Operating: Keep the relative humidity between
5-90% to prevent condensation.
Storage: Store the product in relevant humidity
and temperature conditions.
Warning Information
The device complies with Part 15 of the FCC Rules. Follow these
guidelines to prevent interference:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and
receiver. -
Connect the equipment into an outlet on a different circuit
from the receiver. -
Consult the dealer or a radio/TV technician for
assistance.
FCC Caution: Any unauthorized changes or
modifications can void the user’s authority to operate this
equipment.
Radiation Exposure Statement
This product complies with FCC radiation exposure limits.
Maintain a minimum distance of 20cm between the radiator and your
body for safe operation.
To reduce RF exposure further, keep the device away from the
body or lower the output power if possible.
OEM Integration
This module is intended for OEM integrators only. Follow FCC
guidelines for proper use and compliance.
Frequently Asked Questions (FAQ)
Q: Can this device be used in a portable condition?
A: The device is tested for standalone mobile RF exposure use
conditions. For other usage scenarios, separate reassessment or new
certification may be required.
“`
RTL8852BE User’s Manual
(Realtek RTL8852BE) 11ax RTL8852BE Combo module User’s Manual
Preliminary Version 2021/05/13
Realtek Semiconductor Corp.
No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.:
+886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com
RTL8852BE User’s Manual
CONTENT
ENVIRONMENTAL ………………………………………………………………………………………………………….. 3 OPERATING
………………………………………………………………………………………………………………………….. 3
STORAGE……………………………………………………………………………………………………………………………… 3 MTBF CACULATION
……………………………………………………………………………………………………………… 3 WARNING
………………………………………………………………………………………………………………………… 4
Federal Communication Commission Interference Statement ………………….4
INDUSTRY CANADA STATEMENT …………………………………………………………………………………………… 14
NCC ……………………………………………………………………………………….14
RTL8852BE User’s Manual
ENVIRONMENTAL
Operating
Operating Temperature: -20°C to +70 °C
Relative Humidity:
5-90% (non-condensing)
Storage
Temperature: Relevant Humidity:
-40°C to +80°C (non-operating) 5-95% (non-condensing)
MTBF caculation
Over 150,000hours
RTL8852BE User’s Manual
Warning
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
– Reorient or relocate the receiving antenna. – Increase the separation
between the equipment and receiver. – Connect the equipment into an outlet on
a circuit different from that
to which the receiver is connected. – Consult the dealer or an experienced
radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
RTL8852BE User’s Manual
Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the
radiator & your body.
Radiation Exposure Statement: The product comply with the FCC portable RF
exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual. The further RF exposure
reduction can be achieved if the product can be kept as far as possible from
the user body or set the device to lower output power if such function is
available.
The SAR evaluation is according to KDB 616217, and the module approach
distance restriction is 5 mm.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM
Manual v01 guidance, the following conditions must be strictly followed when
using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15.247, 15.407
2.3 Summarize the specific operational use conditions The module is tested for
standalone mobile RF exposure use condition. Any other usage conditions such
as co-location with other transmitter(s) or being used in a portable condition
will need a separate reassessment through a class II permissive change
application or new certification.
This module is authorized for client device applications under the control of
an indoor access point or subordinate. The final host product must comply with
the following operational restrictions:
a) Cannot have a direct connection to the internet to source the internet to
other clients, access points, subordinates or clients from a wired or direct
connection.
RTL8852BE User’s Manual
2.4 Limited module procedures Not applicable.
2.5 Trace antenna designs Not applicable.
2.6 RF exposure considerations This equipment complies with FCC mobile
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm
between the radiator & your body. If the module is installed in a portable
host, a separate SAR evaluation is required to confirm compliance with
relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas
of the same type with equal or lower gain may also be used with this module.
The antenna must be installed such that 20 cm can be maintained between the
antenna and users.
RTL8852BE User’s Manual
2.8 Label and compliance information The final end product must be labeled in
a visible area with the following: “Contains FCC ID: TX2-RTL8852BE”. The
grantee’s FCC ID can be used only when all FCC compliance requirements are
met.
2.9 Information on test modes and additional testing requirements This
transmitter is tested in a standalone mobile RF exposure condition and any co-
located or simultaneous transmission with other transmitter(s) or portable use
will require a separate class II permissive change re-evaluation or new
certification.
2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module
is tested as a subsystem and its certification does not cover the FCC Part 15
Subpart B (unintentional radiator) rule requirement applicable to the final
host. The final host will still need to be reassessed for compliance to this
portion of rule requirements if applicable.
2.11 Note EMI Considerations Please follow the guidance provided for host manufacturers in KDB publications 996369 D02 and D04.
2.12 How to make changes Only Grantees are permitted to make permissive changes. Please contact us should the host integrator expect the module to be used differently than as granted:
Company Name Company Address Contact Name Tel No E-mail
Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park,
Hsinchu 300, Taiwan
Judy 886-3-578-0211 #13835 judy_hsu@realtek.com
As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
RTL8852BE User’s Manual
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID can not be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
Manual Information To the End User The OEM integrator has to be aware not to
provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately
responsible for the compliance of the Host and Module. The final product must
be reassessed against all the essential requirements of the FCC rule such as
FCC Part 15 Subpart B before it can be placed on the US market. This includes
reassessing the transmitter module for compliance with the Radio and EMF
essential requirements of the FCC rules. This module must not be incorporated
into any other device or system without retesting for compliance as multi-
radio and combined equipment
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
RTL8852BE User’s Manual
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 20cm between the radiator & your body.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux
limites d’exposition aux rayonnements ISED établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre
le radiateur et votre corps.
Radiation Exposure Statement: The product comply with the Canada portable RF
exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual. The further RF exposure
reduction can be achieved if the product can be kept as far as possible from
the user body or set the device to lower output power if such function is
available.
Déclaration d’exposition aux radiations: Le produit est conforme aux limites
d’exposition pour les appareils portables RF pour les Etats-Unis et le Canada
établies pour un environnement non contrôlé. Le produit est sûr pour un
fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF
peut être augmentée si l’appareil peut être conservé aussi loin que possible
du corps de l’utilisateur ou que le dispositif est réglé sur la puissance de
sortie la plus faible si une telle fonction est disponible.
The SAR evaluation is according to KDB 616217, and the module approach
distance restriction is 5 mm
L’évaluation SAR est conforme à KDB 616217, et la restriction de distance
d’approche du module est de 5 mm.
This device is intended only for OEM integrators under the following
conditions: (For module device use) 1) The antenna must be installed and
operated with greater than 20cm between the
antenna and users, and 2) The transmitter module may not be co-located with
any other transmitter or antenna.
RTL8852BE User’s Manual
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module) 1) L’antenne
doit être installé et exploité avec plus de 20 cm entre l’antenne et les
utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires
sur l’émetteur ne seront pas nécessaires. Toutefois, l’intégrateur OEM est
toujours responsable des essais sur son produit final pour toutes exigences de
conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then
the Canada authorization is no longer considered valid and the IC ID can not
be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate Canada authorization.
NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites
(par exemple pour certaines configurations d’ordinateur portable ou de
certaines co-localisation avec un autre émetteur), l’autorisation du Canada
n’est plus considéré comme valide et l’ID IC ne peut pas être utilisé sur le
produit final. Dans ces circonstances, l’intégrateur OEM sera chargé de
réévaluer le produit final (y compris l’émetteur) et l’obtention d’une
autorisation distincte au Canada.
End Product Labeling This transmitter module is authorized only for use in
device where the antenna may be installed and operated with greater than 20cm
between the antenna and users. The final end product must be labeled in a
visible area with the following: “Contains IC: 6317A-RTL8852BE”.
Plaque signalétique du produit final
RTL8852BE User’s Manual
Ce module émetteur est autorisé uniquement pour une utilisation dans un
appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre
l’antenne et les utilisateurs. Le produit final doit être étiqueté dans un
endroit visible avec l’inscription suivante: “Contient des IC: 6317A-RTL8852BE
“.
End Product Labeling The product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
The final end product must be labeled in a visible area with the following:
“Contains IC: 6317A-RTL8852BE”.
Plaque signalétique du produit final L’appareil peut être conservé aussi loin
que possible du corps de l’utilisateur ou que le dispositif est réglé sur la
puissance de sortie la plus faible si une telle fonction est disponible. Le
produit final doit être étiqueté dans un endroit visible avec l’inscription
suivante: “Contient des IC: 6317A-RTL8852BE “.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
Manuel d’information à l’utilisateur final
L’intégrateur OEM doit être conscient de ne pas fournir des informations à
l’utilisateur final quant à la façon d’installer ou de supprimer ce module RF
dans le manuel de l’utilisateur du produit final qui intègre ce module. Le
manuel de l’utilisateur final doit inclure toutes les informations
réglementaires requises et avertissements comme indiqué dans ce manuel.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
RTL8852BE User’s Manual
(ii) for devices with detachable antenna(s), the maximum antenna gain
permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be
such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain
permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in section 6.2.2.3 shall be clearly indicated.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des
instructions précises sur les restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal
d’antenne permis pour les dispositifs utilisant les bandes de 5 250 à 5 350
MHz et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal
d’antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850
MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les
numéros de modèle de l’antenne et les pires angles d’inclinaison nécessaires
pour rester conforme à l’exigence de la p.i.r.e. applicable au masque
d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués
This radio transmitter [IC: 6317A-RTL8852BE] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited for use with this device.
RTL8852BE User’s Manual
Le présent émetteur radio [IC: 6317A-RTL8852BE] a été approuvé par Innovation,
Sciences et Développement économique Canada pour fonctionner avec les types
d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types
d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement
interdits pour l’exploitation de l’émetteur.
NCC Statement 1. 2. (
) 1. 2. XXXyyyLPDzzzz-x
RTL8852BE User’s Manual
NCC LOGO
Japan Statement
Host system must be labeled with “Contains MIC ID:xxxxxx”, MIC ID displayed on
label.
Installing the Wireless PCIe NGFF2230 module Hardware
Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two
external Wi-Fi antennas on I-PEX connectors.
RTL8852BE User’s Manual
Un-installing the Wireless PCIe NGFF2230 module Hardware
RTL8852BE User’s Manual
Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board
and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230
connector port
Installing the WLAN PCIe & Bluetooth USB NGFF2230
RTL8852BE User’s Manual
module Software
Before you proceed with the installation, please notice following
descriptions. Note1: The following installation was operated under Windows 7.
Note2: If you have installed the WLAN driver & utility before, please
uninstall the old version first. A. Execute the “setup.exe”, Click “Next” to
process the installation
B. Select “I accept the terms in license agreement” and click “Next” to
process the installation
C. Click “Next” button.
RTL8852BE User’s Manual
D. Select “Complete” and click “Next” button. E. Click “Install” button.
RTL8852BE User’s Manual
F. Click “Finish” button.
G. Please click “”to continue.
RTL8852BE User’s Manual
H. Please click “”to continue.
RTL8852BE User’s Manual
I. Please click “”to start installation.
J. Please click “”to finish the installation.
Un-installing the Wireless PCIe NGFF2230 module
Software
A. Uninstall the RTL8852BE WLAN Driver from “Start” “Control Panel” “Programs”
Please select items as below and click “Uninstall” to remove RTL8852BE WLAN,
BT driver and MP UI.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>