BRESSER 9810102 Instant Camera Instruction Manual

BRESSER 9810102 Instant Camera Instruction Manual

About this Instruction Manual
Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

Intended Use
This product is intended only for private use. It was developed as an electronic medium for the use of multimedia services.

General Warnings

• Risk of choking — Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard. This product contains small parts that could be swallowed by children.
• Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
• Risk of electric shock — Never bend, pinch or pull the power and connecting cables, extensions and adapters. Protect the cables from sharp edges and heat.Before operating, check the device, cables and connections for damage. Never use a damaged unit or a unit with damaged power cables. Damaged parts must be exchanged immediately by an authorised service centre.
• Risk of property damage! — Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
• Do not expose the device to high temperatures. Do not short-circuit the device or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
• Do not interrupt an on-going data connection to a computer before all data has been transferred. This could lead to data loss for which the manufacturer is not liable.

1. Parts overview

2. Charging the camera

If the camera battery is low, it can be charged using the USB-C charging cable. A charger is not included in the scope of delivery. It is recommended to use a charger in the range of 5V/500 mA to 5V/2A. During charging, the decorative lights on the camera light up. It is recommended not to use the camera while it is charging. It is not possible to print photos when the battery is low.

NOTE: Always adjust the print density setting after charging.

3. Switching the camera on / off

1. Press and hold the “On / Off switch” button for about 2-3 seconds to switch the camera on or off. After switching on, the decorative lights light up. The camera will start with the user interface.
2. The camera automatically recognises a memory card when it is switched on. If no card is inserted, the camera will display the message “No card inserted”.
   NOTE: The camera supports micro SD/TF memory cards* with up to 32 GB. A class 10 or higher memory card is recommended.

3. Take photos
You must insert a MicroSD/TF memory card to take photos. After taking the photo, it will be automatically saved on the MicroSD/TF card.
Select the photo mode in the user interface. In photo mode, press the “Camera” button to take a photo.

3.1 Sticker/Frame
Press the “Up” or “Down” button in photo mode to switch between the available stickers. You can use it to take photos with the mouse, elephant or duck.

3.2 Zoom
Press and hold the “Up” or “Down” button in photo or video mode to zoom in/out.

3.3 Print photo directly after taking it
You can print the photos directly after taking them. First insert the printer paper correctly. (see point
4). Select the Settings mode in the user interface. Activate the “Print after shooting” function. If you now take a photo with the “Camera” button, the photo will be printed immediately. Fold the paper slightly over the teeth of the paper exit and pull it upwards to tear the printout from the paper roll.

3.4 Print photo from album
Select the album mode in the user interface. Short press the “Camera” button to turn on the print function. Select a picture that you like and press the “Mode” button to print the picture.

3.5. Switch between the cameras
In photo mode, press and hold the “Camera” button to switch between the front and rear camera (selfie camera).

4. User interface

4. Printer paper

• The printing paper must be inserted in a specific direction. The glossy side must be facing up. If the paper is inserted incorrectly, the photo will not be printed. Please check the paper direction if printing fails.
• Always pull out the printing paper about 2 cm past the paper exit. Also, make sure the paper is centred and without deviation to either side, otherwise it might cause a paper jam in the camera.
• If printing is enabled and there is no printing paper inside the camera or it is inserted incorrectly, the camera will display “No paper” after taking a photo.
• If the temperature of the camera is too high, it will stop printing and display “High temperature, no print” on the screen. You will temporarily be unable to print. You can still take photos / videos and save them on the memory card to print later.
• If the battery is low, the camera will stop printing and display “Low battery” on the screen. You will temporarily be unable to print. You can still take photos / videos and save them on the memory card to print later.

5. Record videos

You must insert a MicroSD/TF memory card to record videos. After recording, the videos are automatically saved on the MicroSD/TF card.
Select the video mode in the user interface. In video mode, press the camera button to start recording a video. Press the camera button again to stop recording.

6. Album mode

Select album mode in the user interface to view the last photos/videos taken.
In album mode, press the “Up” or “Down” buttons to switch between your recordings.

Video playback
When playing videos, short press the “Mode button” to play or pause the current video.

Deleting files
Long press the camera button to choose to delete a single file or all files.

7. Setting mode

Select the “Settings” mode in the user interface to access the settings mode. Use the “Up” / “Down” button to select the desired setting. Press the “Mode” button to
– confirm the selected setting.
– Press the “Mode” button to call up the setting options, which you can select with the “Up” / “Down” button and then confirm with the mode button.

Press the “Back” button to exit the setting mode.

8. MP3 Player

Save your MP3 files in the “MP3” folder on the MicroSD/TF card to be able to play back music files.
Mode button: Short press = play/pause
Up button: Short press = Next track / Long press = Increase volume
Down button: Short press = Previous track / Long press = Decrease volume

9. Reset the device to factory settings

If the camera no longer works properly, there are two ways to reset it to the factory settings:
– Under Settings, select “Do the factory reset?” and press the “Mode” button to confirm. Press the “Up” or “Down” button to select “OK” and press the “Mode” button to start the factory reset.
– Insert a pointed object into the reset opening below the USB connection socket.

10. Technical data

Notes on cleaning

• Turn off the camera
• Clean the lenses only with a soft, lint-free cloth, (e.g. microfibre cloth). To avoid scratching the lenses, use only gentle pressure with the cleaning cloth.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.

EC Declaration of Conformity

Bresser GmbH has issued a “Declaration of Conformity” in accordance with applicable guidelines and corresponding standards. The full text of the EC declaration of conformity is available at the following internet address:
www.bresser.de/download/9810202/CE/9810202_CE.pdf

Disposal

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage! As per the Directive 2012/19/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner. Empty, old batteries must be disposed of at battery collection points by the consumer. You can find out more information about the disposal of devices or batteries produced after 6 January 2006 from your local waste-disposal service or environmental authority.

Drain the battery completely before disposal.

Warranty & Service
The regular warranty period is 2 years and begins on the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required.

You can consult the full warranty terms as well as information on extending the warranty period and details of our services at www.bresser.de/warranty_terms.

Contact

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way • Edenbridge,
Kent TN8 6HF • Great Britain

Errors and technical changes reserved.
Manual_9810102_Instant-camera_de-en_DIEMAUS_v052024a

Read More About This Manual & Download PDF:

References

• konsoleH :: Login
• Bresser | BRESSER Ersatz-Fotorollenset (5 Stück) für Kinder-Sofortbildkamera | Expand Your Horizon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>