SPERAS T50 USB-C Rechargeable Hunting Flashlight User Manual

: August 13, 2024
: SPERAS

Table of Contents

SPERAS T50 USB-C Rechargeable Hunting Flashlight
Product Usage Instructions
Remote Pressure Switch:

SPERAS T50 USB-C Rechargeable Hunting Flashlight

Specifications :

Output:
- Turbo: 4000lm
- High: 1800lm
- Medium: 500lm
- Low: 200lm
- ECO: 20lm
- Strobe: 4000lm
- SOS: 500lm
Beam Distance: Up to 738m
Runtime:
- Turbo: 3.7h
- High: 4.5h
- Medium: 6.4h
- Low: 16h
- SOS: 147h
Beam Intensity:
- Turbo: 136,250cd
- High: 54,250cd
- Medium: 17,500cd
- Low: 7,000cd
- ECO: 775cd
LED: CREE XHP70.3 HI
Lens: Smooth Reflector
Battery Source: 121700 Battery Pack or 221700 Lithium Battery
Charging: USB-C charging
Impact Distance: 1.5m
Waterproof Rating: IP68 (2 meter submersible)
Material: Aerospace 6061 Aluminum Alloy
Finish: Premium Type III Hard-anodizing
Dimension: 254(Length)63.6(Head)25.4(Tube)mm
Net Weight: 254g(excl.battery)

Product Usage Instructions

Battery Installation:
Before the first use, remove the insulating film of the battery in the flashlight. Ensure the positive polarity side of the battery faces towards the flashlight head.

Operating Instructions :
To operate the flashlight:

To activate Turbo mode, perform a quick double click.
To enter STROBE mode, double-click quickly again.
To access SOS mode, perform another quick double click.
A single click will return to the state before strobe.

Power Indicator :
The built-in power indicator on the side switch will display the remaining power level for 5 seconds upon turning on the flashlight.

Green: 100%-70% power remaining
Orange: 70%-30% power remaining
Red: 30%-10% power remaining
Red Flash: 10%-1% (indicating very low power level)

Charging:
The T50 supports 5V/2A charging. Insert the USB-C cable into the port and connect to an adapter to charge. The indicator will show:

Green: Fully charged
Red: Charging in progress
Orange: Check battery seating or faulty battery

The flashlight automatically turns off during charging. Pressing the tail button will switch to LOW mode when the cable is disconnected.

Remote Pressure Switch:

To use the remote pressure switch S1/S2/S3:

Connect the RMC V2 to the type C port of the flashlight.
Press down the tail button of the flashlight to activate.

FAQ :

Q: How long does it take to fully charge the T50 flashlight?
A: The full charging time is approximately 5.2 hours for the T50 model.
Q: Can the T50 flashlight be used while charging?
A: No, the T50 cannot be operated while it is charging.

T50 User manual

Danger and Warning

Please read the user manual before first use.
DO NOT shine light directly into eyes. This may cause temporary blindness and/or cause permanent damage to the eyes.
DO NOT cover the light head when the flashlight is on or place the light head on the ground. The heat dispersion of the light may cause damage to the flashlight itself or even result in burning other objects.
Keep out of reach of children.
DO NOT activate the highest mode constantly to prevent the flashlight body from overheating and hurting the user’s hand.
Please insert SPERAS batteries or SPERAS recommended batteries.

Inside the box

Optional accessories

Specification

The above data has been measured in accordance with international flashlight testing standards ANSI/NEMA FL1 using SPERAS 7.4V/5000mAh 21700 battery under laboratory conditions.

Product Overview

The SPERAS T50 is a high-tech hunting flashlight. Equipped with an advanced structure and an advanced driver design, the maximum output can reach up to 40001m with a maximum beam distance of 738m. It supports USB-C fast charging reaching a full charge within 5.2 hours. Powered by 2pcs of 21700 batteries, 5000mAh, it provides a long run time of up to 147 hours. It also supports a remote pressure switch, suitable for all kinds of gun mounts and scope mounts to get easier and more effective usage. T50 is an ideal flashlight for hunters, search or rescue, or other outdoor lighting requirements.

Battery Installation

Before the first use, please remove the insulating film of battery in the flashlight. And if the battery needs to be changed, make sure the positive polarity side of the battery faces toward the direction of the flashlight head (the side of the LED).

Operating Instructions

Tail Button
- On the OFF state, slightly press to enter Memory mode; press down to enter Memory mode; double quick slightly press to enter Strobe.
- Press and hold the side button and click the tail button to enter ECO.
- Can only be turned ON/OFF by the tail button.
Side Button
- On the ON state, click the side switch to circle from low, medium, high, turbo; quick double click to enter STROBE; another double quick click to enter SOS; one click to return the state before strobe.

Power Indicator When turning the flashlight on, the built-in indicator on the side switch will indicate the remaining power level for 5 seconds.

Power indicator will display one of the following:
- Green: 100%-70%
- Orange: 70%-30% Red: 30%-10%
- Red Flash: 10%-1%, (Alert flash to indicate very low power level).

Charging

The T50 supports 5V/2A charging. Insert the cable into the type-C port and connect the adapter to charge. When charging, the indicator will display as follows:
Green: Fully charged
Red: Busy charging
Orange: Check the battery is correctly seated or faulty battery
The flashlight turns off automatically during charging.
Pressing the tail button will enter LOW mode when the charging cable is released.

How to use the Remote Pressure Switch

Before using the S1/S2/S3 button, please plug the RMC V2 into the type C port of the flashlight and then press down the tail button of the flashlight.
S1:ON/OFF/Momentary ON
- In the OFF state, click the S1 button, the flashlight will turn on (enter the memory mode); click again, the light will turn off.
- In the OFF state, press and hold the S1 button to momentary ON, release to turn off.
S2/S3:Strobe/Change mode
- In the OFF state, press the S2/S3 button will enter the strobe mode, release to turn off.
- In the ON state, press the S2/S3 for 0.5s will enter the strobe mode, release will to the previous state.
- In the ON state, click S2/S3 button to change the mode of the flashlight.
- Note: the S2 and S3 button have the same function

Usage and Maintenance

Please fully charge the battery before initial use.
To maintain the waterproof rating, please lubricate the O-ring with silicone safe lubricant and replace broken O-rings as soon as possible.
If the light will not be used for a long period or when transported, please unscrew the tail cap and remove the battery to break the circuit.

Warranty

The product is provided with a 5-year warranty. Any non-artificial damage, please contact the SPERAS after-sales department.
The warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance or repairs by anyone other than an authorized retailer or SPERAS itself

Beyond Warranty

Free warranty DO NOT cover any damage or failure caused by:
Normal wear up
Damages caused by disassembling, modifying the flashlight
Damages caused by rough operation or misuse
Improper maintenance or repairs by anyone other than an authorized retailer or SPERAS itself

Shenzhen Speras Lighting Co., Ltd
Add: 4F, Building G, Gangshen Innovation Park,
Huaning Road, Dalang Street, Longhua District,
Shenzhen, China. 518109
Tel.: +86-755-2107 2597 Email: info@speraslight.com
Website: www.sperasflashlight.com

Product Model No.:
Serial No.:
Date of Purchase:
Dealer Signature / Stamp

Thank you for choosing SPERAS.

The SPERAS flashlight is covered by a 5-year warranty from the date of purchase.
Please ask the dealer/distributor to fulfill the date of purchase and sign/stamp the warranty card after purchase.
Contact the dealer/distributor of SPERAS first if help needed.
Notice : The warranty covers manufacturer defects solely and becomes invalid if the flashlight is subjected to work by an unauthorized party