TAC 2004-2024 Steps Running Boards Compatible Installation Guide
- August 16, 2024
- TAC
Table of Contents
INSTALLATION INSTRUCTIONS
3″ BENT END SIDEBARS
2004-2024 NISSAN TITAN CREW CAB
2016-2024 NISSAN TITAN XD CREW CAB
PART#240700
PARTS LIST:
| 1 | Driver/Left Sidebar |
|---|---|
| 1 | Passenger/Right Sidebar |
| 3 | Driver/Left Mounting Brackets |
| 3 | Passenger/Right Mounting Brackets |
| 12 | 8-1.25mm x 30mm Hex Bolts |
| 12 | 8-1.25mm x 25mm Combination Hex Bolts |
| 12 | 8mm Lock Washers |
| 6 | 8mm x 24mm OD x 2mm STD Flat Washers |
| 6 | 8mm x 16mm OD x 1.6mm Small Flat Washers |
| 6 | 8mm Nylon Lock Nuts |
- Passenger/Right Side Mounting Brackets
- Driver/Left Side Mounting Brackets
- Front of Vehicle
A: Driver Side
B: Passenger Side
- Insert locations for brackets
- Front of Vehicle
Installation Complete
PROCEDURE:
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
-
Start installation at the front of the driver side of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Figure 1). NOTE: Remove the plastic plug or any insulation on the side panel to locate the threaded holes.
-
Select (1) driver side Mounting Bracket. Attach the Bracket to the mounting location with:
a. Models with threaded stud: Attach Bracket to stud with (1) 8mm x 24mm STD Flat Washer and (1) 8mm Nylon Lock Nut. Next, insert (1) 8mm x 30mm Hex Bolt with (1) 8mm Lock Washer and (1) 8mm x 16mm Small Flat Washer through the remaining lower hole in the Bracket and into the threaded hole, (Figures 1A, 2 and 3). Do not tighten hardware at this time.
b. Models without threaded stud: Attach Bracket to the upper threaded hole with (1) 8mm x 24mm STD Flat Washer, (1) 8mm Lock Washer and (1) 8mm x 30mm Hex Bolt. Attach Bracket to the lower threaded hole with (1) 8mm x 16mm Small Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Bolt, (Figure 1B & 2). Do not tighten hardware at this time. -
There are (4) mounting locations along the body panel. Bracket installation will use the 1st, 2nd and 4th mounting locations. Repeat the appropriate Steps 2–3 to install the center and rear Mounting Brackets, (Figures 2–6). NOTE: The cradles on the Mounting Brackets should be facing the rear of the vehicle when properly installed, (Figure 4).
-
Once all three Mounting Brackets are partially installed, carefully place the driver Sidebar onto the
Mounting Brackets. Use the included (6) 8mmx 25mm Combination Bolts to attach the Sidebar to the
Mounting Brackets, (Figures 5 & 6). -
Level and adjust the Sidebar and tighten all hardware at this time.
-
Repeat Steps 2–6 for passenger Sidebar installation.
-
Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment , wax this product after installing. Regular
waxing is recommended to add a protective layer over the finish. Do not use
any type of polish or wax that may contain abrasives that could damage the
finish. For stainless steel: Aluminum polish may be used to polish small
scratches and scuffs on the finish. Mild soap may be used also to clean the
Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Driver Side Installation Pictured
(Fig 1A) Up to 2015 driver side rear mounting location pictured. Note: Remove
plastic plugs to locate factory threaded holes
- Threaded Stud
- Threaded Hole
(Fig 1B) 2016-on driver side rear mounting location pictured. Note: two factory threaded holes only
- (2) Threaded Holes
(Fig 2) Driver/left Bracket illustrated for example only
-
8mm x 30mm Hex Bolt
8mm Lock Washer
8mm x 24mm STD Flat Washer
Or
8mm x 24mm STD Flat Washer
8mm Nylon Lock Nut -
8mm x 30mm Hex Bolt
8mm Lock Washer
8mm x 16mm Small Flat Washer
(Fig 3) Up to 2015 Driver side front Bracket installed
(Fig 4) Driver side Brackets installed. Note all cradles face back of vehicle
(Fig 5) Driver side center mounting location pictured
-
8mm x 24mm STD Flat Washer
8mm Nylon Lock Nut
Or
8mm x 30mm Hex Bolt
8mm Lock Washer
8mm x 24mm STD Flat Washer -
8mm x 30mm Hex Bolt
8mm Lock Washer
8mm x 16mm Small Flat Washer -
(2) 8mm x 25mm
Combo Bolts
(Fig 6) Driver side rear mounting location pictured
-
8mm x 30mm Hex Bolt
8mm Lock Washer
8mm x 16mm Small Flat Washer -
(2) 8mm x 25mm
Combo Bolts
www.tacautoparts.com 03/28/16 Rev 3 (DP)