TAC 135190 Running Board 2019-2024 Toyota RAV4 Instruction Manual
- August 13, 2024
- TAC
Table of Contents
TAC 135190 Running Board 2019-2024 Toyota RAV4
Product Specifications
- Model : Running Board 2019-2024 Toyota RAV4
- Part Number: 135190
- Manufacturer: TAC Auto Parts
Product Usage Instructions
Installation Steps:
- Begin with the Passenger/Right Front mounting location. Insert the Bolt Plate into the hole in the outer rocker panel and slide the Plastic Retainer onto the threads of the bolt plate.
- Insert the L-shaped bolt into the hole in the inner floor panel and secure it with the Plastic Retainer.
- Attach the Passenger/Right Front Mounting Bracket using the appropriate hardware for the L-shaped bolt and Bolt Plate. Do not tighten the hardware yet.
- Repeat steps 1-3 for the Passenger/Right Center and Rear mounting locations.
- Carefully unwrap the Passenger/Right Running Board and attach it to the mounting brackets using the provided hardware.
- Repeat steps 1-5 for the Driver/Left Running Board installation.
- Perform periodic inspections to ensure all hardware is secure and tight.
Cleaning and Maintenance:
To clean the Running Board, use mild soap and water. Avoid using polishes or
waxes that contain abrasives to prevent damage to the finish. For stainless
steel boards, aluminum polish can be used to treat small scratches and scuffs.
PARTS LIST
- 1 Driver/Left Running Board
- 4 10-1.50mm Hex Nuts
- 1 Passenger/Right Running Board
- 8 8-1.25mm x 40mm Bolt Plates
- 1 Driver/Left Front Mounting Bracket
- 8 8mm Plastic Retainers
- 1 Passenger/Right Front Mounting Bracket
- 8 8mm x 24mm x 2mm Flat Washers
- 1 Driver/Left Center Mounting Bracket
- 8 8mm Lock Washers
- 1 Passenger/Right Center Mounting Bracket
- 8 8-1.25mm Hex Nuts
- 1 Driver/Left Rear Mounting Bracket
- 12 6-1.0mm x 20mm T-Bolts
- 1 Passenger/Right Rear Mounting Bracket
- 12 6mm x 22mm x 2mm Flat Washers
- 4 10mm L-Shapped Bolts
- 12 6mm Lock Washers
- 4 10mm Plastic Retainers
- 12 6-1.0 Hex Nuts
- 4 10mm x 30mm x 2.5mm Flat Washers
- 4 Locking Plates
- 4 10mm Lock Washers
PROCEDURE
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED TO INSTALL.
-
Locate the Passenger/Front mounting location and remove the factory round rubber plug in the bottom of the outer rocker panel, (Figures 1, 2, 5 & 7).
-
Select the Passenger/Right Front Mounting Bracket, (Figure 2). Hold the mounting bracket up to the mounting location, (Figures 2 & 3). Trace the outline of the bracket onto the plastic cover where the top of the Passenger/Right Front Mounting Bracket touches, (Figure 4).
-
Move to the center mounting location. Repeat Step 3 to mark the Passenger/Right Center and Rear plastic covers, (Figures 5—8).
-
Remove the plastic covers on the underside of the vehicle.
-
Cut each plastic cover along the marks to allow the Mounting Brackets clearance, (Figures 9A—10B).
IMPORTANT: The covers must be cut for bracket clearance. Remove any rubber sealant that may interfere with bracket installation, (Figure 11). -
Reattach the cut plastic covers.
-
8. Move to the Passenger/Right Front mounting location. Select (1) 8mm Bolt Plate. Insert the Bolt Plate into the hole in the outer rocker panel, (Figure 12A). Slide (1) 8mm Plastic Retainer onto the threads of the bolt plate to hold the bolt in position, (Figure 12B).
-
Select (1) 10mm L-Shapped Bolt, (Figure 12C). Insert the L-shaped bolt into the hole in the inner floor panel. Slide (1) 10mm Plastic Retainer on the threads of the bolt plate to hold the bolt in place, (Figure 12B).
-
Select the Passenger/Right Front Mounting Bracket.
-
For the 10mm L-shaped bolt. Attach the bracket to the L-shaped bolt with (1) Locking Plate, (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut.
-
For the 8mm Bolt Plate. Attach the bracket to the bolt plate with (1) 8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figures 13—15). Do not tighten hardware at this time.
-
Move to the Passenger/Right Center mounting location, (Figure 1). Select the Passenger/Right Center Mounting Bracket. Repeat Steps 8—10 to attach the bracket to the panels, (Figures 16 & 17).
-
Move to the Passenger/Right Rear mounting location, (Figures 1 & 18). Insert (2) 8mm Bolt Plates into the outer hole in the outer rocker panel and the inner hole in the inner floor panel. Slide (2) Plastic Retainers to hold the bolt plate in place, (Figures 12A & 19). Select the Passenger/Right Rear Mounting Bracket. Attach the bracket to the Bolt Plates with (2) 8mm Flat Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts, (Figures 20 & 21).
-
Select and carefully unwrap the Passenger/Right Running Board. Insert (6) 6mm T-Bolts in to the channels on the bottom of the Running Board, (Figure 22). Attach the Running Board to the mounting brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers, and (6) 6mm Hex Nuts, (Figure 23).
-
Repeat Steps 2—13 for the Driver/Left Running Board installation, (Figures 24—26).
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Running Board. Mild soap may be used to clean the Running Board.
Passenger/Right Side Installation Pictured
Driver/Left Side Installation Pictured
FAQ
Q: Can I use abrasive polish or wax on the Running Board?
A: No, avoid using any polish or wax that may contain abrasives as it could
damage the finish. Use a mild soap for cleaning instead.
Q: How often should I inspect the installation?
A: Periodic inspections are recommended to ensure all hardware remains secure
and tight. Check regularly for any loosened components.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>