TAC 3B-JL230T 3 Inch Bull Bar Installation Guide

: August 13, 2024
: TAC

Table of Contents

TAC 3B-JL230T 3 Inch Bull Bar
Product Usage Instructions
PARTS LIST
PROCEDURE
Passenger/Right Side Installation Pictured
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAC 3B-JL230T 3 Inch Bull Bar

Specifications:

Product Name: 3 Bull Bar
Compatible Vehicles: 2018-2024 Jeep Wrangler JL (4DR & 2DR, Excluding Plug-in Hybrid Models), 2020-2024 Jeep Gladiator (Excluding Mojave Trim)
Part Number: 3B-JL230T
Manufacturer Website : www.tacautoparts.com

Product Usage Instructions

Installation:

Remove splash guard and bracket from the front of the vehicle.
Insert the 10mm Bolt/Nut Plate into the bottom of the frame and out through the hex hole in the side of the frame. Use the Retainer to hold the Bolt/Nut Plate in place.
Attach the passenger/right Mounting Bracket to the Bolt/Nut Plate and Retainer using the provided hardware.
Repeat the same steps for the driver/left side Mounting Bracket installation.

Maintenance:
To protect your investment and maintain the Bull Bar:

Wax the product after installation. Regular waxing is recommended to add a protective layer over the finish.
Avoid using polish or wax-containing abrasives that could damage the finish.
For stainless steel finishes, use aluminum polish for scratches and scuffs. Mild soap can also be used for cleaning.
For gloss black finishes, mild soap is recommended for cleaning.

2018-24 WRANGLER JL (EXCL. PLUG-IN HYBRID MODELS, 2021-2024 V8 ENGINE, 20-23 RUBICON TRIM, 4XE HYBRID ENG INE AND TRIMS WITH FOX HYDRAULIC JOUNCE BUMPERS AND UPGRADED 2.5IN FOX INTERNAL BYPASS SHOCKS WITH EXTERNAL RESERVOIR) 2020-24 GLADIATOR (EXCL. MOJAVE & RUBICON TRIM AND TRIMS WITH FOX HYDRAULIC JOUNCE BUMPERS AND UPGRADED 2.5IN FOX INTERNAL BYPASS SHOCKS WITH EXTERNAL RESERVOIR)

PARTS LIST

PROCEDURE

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. CUTTING IS REQUIRED. ASSISTANCE IS RECOMMENDED.
Remove the plastic splash guard from under the front bumper and place it on a clean, stable work surface, (Figures 1 & 5). Models with steel skid plate, skid plate must be removed and cannot be reinstalled.
- Models with plastic splash guard:
1. Starting on the passenger/right side, locate the lower hex-shaped hole in the outside of the frame, (Figure 2). Insert (1) 10mm Bolt/Nut Plate, (end with welded nut first), into the open end of the bottom of the frame and push the welded hex bolt through the hex-shaped hole, (Figure 3). Thread (1) 10mm Plastic Retainer onto the Bolt/Nut Plate to hold it in position. NOTE: Plastic Retainer is designed to hold the Bolt Plate in position to help with Bracket installation. Use is not mandatory. IMPORTANT: Remove the steel frame bracket for the splash guard if more room is necessary to install the Bolt/Nut Plate, (Figure 1).
2. Select the passenger/right side Mounting Bracket, (Figure 4). Attach the Bracket to the Bolt on the Bolt Nut Plate with (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut. Leave loose at this time. Grab the threaded end of the 10mm Bolt/Nut Plate and rotate it until the top end with the welded Nut lines up with the round hole in the outside of the frame and the top mounting hole in the Bracket. Attach the Bracket to the Bolt/Nut Plate with (1) 10mm x 35mm Hex bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figures 4 & 7). Snug but do not fully tighten Bracket hardware at this time. Reinstall the steel frame bracket for the splash guard if previously removed.
- Models with steel skid plate:
1. Select the passenger/right side Mounting Bracket. Attach the Bracket to the lower threaded hole in the outside of the frame with (1) 10mm x 35mm Hex bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figure 4). Do not tighten.
2. Repeat the previous Steps to install the Bolt/Nut Plate into the open end of the frame and up to the top mounting hole, (Figure 2). Attach the top of the Bracket to the Nut end on the Bolt /Nut Plate with (1) 10mm x 35mm Hex bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer. Snug but do not fully tighten the Bracket hardware at this time.
Repeat the appropriate Step 2 for driver/left side Mounting Bracket installation.
Position the splash guard back up to the vehicle and temporarily attach with the factory hardware. Trace the location of the Mounting Brackets onto the back of the splash guard, (Figure 5). Remove the splash guard and move it to a clean stable work surface. Carefully cut openings in the splash guard to clear the Bull Bar. NOTE: To maintain the integrity of the plastic Splash Guard, remove only material necessary to clear the Bull Bar and Brackets. Make small cuts and check the fit often before final installation.
Reinstall the splash guard with factory hardware.
With assistance, position the Bull Bar up to the Mounting Brackets. Use the included (4) 8mm x 35mm Hex Bolts, (4) 8mm Lock Washers and (4) 8mm Flat Washers to attach the Bull Bar to the Mounting Brackets, (Figures 6 & 7). Do not tighten hardware at this time.
Align the Bull Bar properly and fully tighten all hardware.
Do periodic inspections to the installation to make sure is secure and tight.

To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Bull Bar. For gloss black finishes: Mild soap may be used to clean the Bull Bar.

Passenger/Right Side Installation Pictured

www.tacautoparts.com

FAQ

Q: Can this Bull Bar be used on all Jeep Wrangler JL and Gladiator models?
A: The Bull Bar is compatible with 2018-2024 Jeep Wrangler JL (4DR & 2DR, Excluding specific models) and 2020-2024 Jeep Gladiator (Excluding certain trims). Please refer to the product specifications for detailed compatibility information.