LEDBLE KQ-NL-LED LED Strip Light User Guide
- August 13, 2024
- LEDBLE
Table of Contents
LEDBLE KQ-NL-LED LED Strip Light
Specifications
| Item | Specification |
|---|---|
| LED Type | SMD 5050 |
| Color | RGB |
| Input Voltage | 12V |
| Power Consumption | 24W |
| Remote Control | 44-key infrared |
| Battery Type | CR2025 |
Product Usage Instructions
Product Overview
- RGB LED strip
- 44-key infrared remote controller (with CR2025 battery)
- IR receiver
- Power adapter
- Operating instructions
44-key Remote Control
Refer to the diagram below for the functions of each button on the remote
control:
- Color selection buttons
- Static mode buttons
- Dynamic mode buttons
- Brightness adjustment buttons
- Speed adjustment buttons
- Power on/off button
Installation
- Connect the LED strip to the IR receiver.
- Connect the IR receiver to the power adapter.
- Plug the power adapter into a power outlet.
- Use the remote control to operate the LED strip lights.
WARNING: DO NOT IMMERSE IN WATER. DO NOT EXPOSE TO FIRE. KEEP AWAY FROM CHILDREN UNDER THE AGE OF 3. CHOKING HAZARD – SMALL PARTS. USE UNDER ADULT SUPERVISION.
General Troubleshooting
- If the LED strip does not light up, check the connections and ensure the power adapter is plugged in.
- If the remote control does not work, replace the CR2025 battery.
- If the LED strip lights up but does not respond to the remote control, ensure there are no obstructions between the remote and the IR receiver.
Product Overview
Package contents
- LED strip
- 44-key infrared remote controller (with CR2025 battery)
- Bluetooth control box
- Power adapter
- Operating instructions
- Mounting accessories
Tips : The arrows must be aligned, otherwise will not work
44 key remote control
Remote control size
Common Troubleshooting
The controller was connected the power, but not light up
- Check the input power supply: please use the power adapter that we equipped or the same specification adapter as ours The input voltage must meet the voltage required by the lamp When the input voltage is too low, the lamp will not be light, and the high voltage may damage the circuit. The output power of the adapter (KW value) must be equal to or greaterthan the power of the LED lamp belt.
- Check whether the controller and the lamp are connected correctly, Make sure each interface is connected correctly.
- Check whether the remote control is open. control LED light beetremote control does not work or can’t
- Check whether the insulation sheet is removed from the remote control.
- Make sure the battery on the remote control is installed correctly.
- Ensure that is being used within 8 meters and aligned to the infraredreceiver of the controller.
- Try to replace the battery
Attentions:
- Lamp belt must be used under 24V
- Remote control must be aligned to the Infrared Receiver of the controllers
- The lamp belt must be connected correctly as showed method
WARNING: DO NOT IMMERSE IN WATER DO NOT IMMERSE IN FIRE CHILDREN UNDER THE AGE OF 16 SHOULD USE THIS PRODUCT UNDER ADULT SUPERVISION.
If you have any question after receiving the products, please contact our customer service, we will reply to you within 24 hours.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note : The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).
Download App
FAQ’s
Q: How do I install the LED strip lights?
A: Connect the LED strip to the IR receiver, connect the IR receiver to the power adapter, plug the power adapter into a power outlet, and use the remote control to operate the LED strip lights.Q: What should I do if the LED strip does not light up?
A: Check the connections and ensure the power adapter is plugged in.Q: What should I do if the remote control does not work?
A: Replace the CR2025 battery in the remote control.Q: What should I do if the LED strip lights up but does not respond to the remote control?
A: Ensure there are no obstructions between the remote and the IR receiver.Q: What is the input voltage for the LED strip lights?
A: The input voltage is 12V.Q: What type of battery does the remote control use?
A: The remote control uses a CR2025 battery.Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>