SHERPA The Atlas 2024 Land Cruiser Installation Guide
- August 9, 2024
- SHERPA
Table of Contents
SHERPA The Atlas 2024 Land Cruiser
Product Specifications
- Number of Crossbars: 10
- Number of Mounts: 8 (2 Adjustable, 2 Front, 2 Rear, 2 Middle)
- Number of Sideplates: 2
- Number of Rubber Spacers: 6
Product Usage Instructions
Before Installation
- Remove your stock roof rack (if applicable).
- Loosen all stock rack bolts before fully removing any of them.
- Work slowly when removing the stock rack to prevent any damage.
Using TNuts for Mounts
Adjustable Mount Assembly
Required Components
- 4 1/4-20×1 Carriage Bolts
- 4 1/4 Washers
- 4 1/4-20 Nuts
Secure the lower and upper adjustable mount brackets, leaving the hardware loose for adjustment later.
Front Mount Assembly
Required Components
- 1 Crossbar
- 2 Front Mounts
- 4 1/4-20 x 9/16 Hex Bolts
- 4 1/4 Flat Washers
- 4 TNuts
Secure the top of the mounting bracket to the crossbar, leaving the hardware loose for later adjustment.
Rear Mount Assembly
Required Components
- 1 Crossbar
- 2 Rear Mounts
- 4 1/4-20 x 9/16 Hex Bolts
- 4 1/4 Flat Washers
- 4 TNuts
Repeat the assembly for rear mounts.
Middle Mount Assembly
Required Components
- 1 Crossbar
- 2 Middle Mounts
- 4 1/4-20 x 9/16 Hex Bolts
- 4 1/4 Flat Washers
- 4 TNuts
If your rack has middle mounts, repeat the assembly steps.
Mount Installation on Vehicle
01 Install on Vehicle
Required Components
- 4 M8-1.25×45 Hex Bolts per mount assembly
- 4 M8 Bonded Washers per mount assembly
- 2 Rubber Spacers per mount assembly
Position the mounting bracket over the rubber spacer and secure using bonded washers and bolts. Apply blue threadlocker to bolt threads before securing.
Center the Mounts
After securing the main support crossbar, center all bars on the vehicle
using a tape measure. Tighten the hardware to the crossbar once centered.
Sideplate Installation
Sideplate Install
Required Components
- 2 Sideplates
- 4 1/4-20×1 Socket Bolts per mount assembly
- 4 1/4 Washers per mount assembly
Align the sideplates with the ends of the main support crossbars and secure them using bolts and washers. Adjust the position to match the vehicle’s curvature before tightening all hardware.
Frequently Asked Questions (FAQ)
-
Q: Do I need any special tools for installation?
- A: Basic hand tools like wrenches and screwdrivers are sufficient for installing the Atlas Rack System.
-
Q: Can I install the rack system alone?
- A: While it’s recommended to have assistance during installation, it is possible to install the rack system alone with proper care and attention to detail.
-
Q: How do I clean and maintain the rack system?
- A: Regularly clean the rack system with mild soap and water. Avoid using harsh chemicals or abrasives that may damage the finish. Check and tighten bolts periodically to ensure secure attachment.
The Atlas
HARDWARE CHECKLIST
BEFORE YOU START
Remove your stock roof rack (if applicable). Loosen all stock rack bolts
before fully removing any of them. This will prevent the capture plates from
working loose inside of the roof. Work slowly when removing the stock rack as
not to break the plastic sleeves.
The below assembly images may differ slightly in appearance from actual product.
Mounts
Adjustable Mount
Required Components
- 4 1/4”-20×1” Carriage Bolts
- 4 1/4” Washers
- 4 1/4”-20 Nuts
Secure the lower and upper adjustable mount brackets leaving the hardware loose so that it can be adjusted during a later step.
front mount Assembly
Required Components
- 1 Crossbar
- 2 Front Mounts
- 4 1/4”-20 x 9/16” Hex Bolts
- 4 1/4” Flat Washers
- 4 Tnuts
Drop 4 tnuts into the slots on the crossbar and line them up with the holes in mounts. Secure top of the mounting bracket to the crossbar leaving the hardware loose so that it can be adjusted during a later step.
Note: Front mounts have the “F” designation at the end.
Rear mount Assembly
Required Components
- 1 Crossbar
- 2 Rear Mounts
- 4 1/4”-20 x 9/16” Hex Bolts
- 4 1/4” Flat Washers
- 4 Tnuts
Repeat assembly.
Note: Rear mounts have the “R” designation at the end.
Mid mount Assembly
Required Components
- 1 Crossbar
- 2 Rear Mounts
- 4 1/4”-20 x 9/16” Hex Bolts
- 4 1/4” Flat Washers
- 4 Tnuts
If your rack comes with a middle mount(s), repeat assembly.
Note: Middle mounts have the “M” designation at the end.
Mount Install
Install on vehicle
Required Components
- 4 M8-1.25×45 Hex Bolts per mount assembly
- 4 M8 Bonded Washers per mount assembly
- 2 Rubber Spacers per mount assembly
Position the mounting bracket over the rubber spacer. Apply a drop of blue threadlocker to each of the bolt threads and secure them with bonded washers passed through the bracket, rubber, and into the holes in the roof.
Note: Chamfered corner on the lower part of the mount faces the front of the vehicle.
The bonded washers should compress and become flat, but not concave. Do not over tighten these mounts.
Center the Mounts
After the main support crossbar have been secured to the vehicle, use a
tape measure and center all of the bars on the vehicle. Measure from the
inside edge of the mount to the outside face of the crossbar and make these
equal side-to-side. Tighten the hardware to the crossbar.
Sideplates
Sideplate install
Required Components
- 2 Sideplates
- 4 1/4”-20×1” Socket Bolts per mount assembly
- 4 1/4” Washers per mount assembly
Align the small slots in the sideplates with the ends of the main support crossbars. Secure them using bolts and washers. Leave the bolts loose enough to move the sideplate to the position that matches the curvature of the vehicle.
Once the rack is positioned correctly, tighten down all of the hardware for the sideplates.
Wind Fairing
Fairing Assembly
Required Components
- 1 Crossbar
- 6 1/4”-20×1/2” Socket Bolts
- 6 1/4” Flat Washers
- 6 Tnuts
Drop 6 tnuts into the slots on the crossbar and line them up with the holes in the fairing. Secure with 6 bolts and washers.
Fairing installation
Required Components
- 4 1/4”-20×1” Socket Bolts
- 4 1/4” Flat Washers
Position the wind fairing in line with the diagonal slot at the front of the rack. Align the bottom of the fairing with the tip of the roof rack and secure it using bolts and washers.
The fairing can be adjusted up or down if wind noise is detected. Small adjustments make a big difference here.
Mount Install
Install on vehicle
- Final adjustments can be made to the front leveling mounts once the rack has been assembled on the vehicle.
- Apply upward pressure on the front of the rack and insert a microfiber towel or other soft buffer between the front of the rack and the vehicle’s roof. Adjust the angle and height of the mounting foot to sit as firmly on the vehicle’s roof as possible, then tighten the hardware in the center of the mount. If possible, it is recommend to position these mounts on the plastic gutter trim to prevent possible paint damage.
- Once the mounts are in the correct position, remove the buffer and inspect the rack to make sure it is firm.
Install crossbars
Required Components
Remaining Crossbars
- 4 1/4”-20 x 1” Socket Bolts per crossbar
- 4 1/4” Flat Washers per crossbar
Secure all of the remaining crossbars to the rack system. Space evenly or position according to your load requirements.
NOW GET OUT THERE AND EXPLORE.
WELCOME TO THE SHERPA FAMILY!WELCOME TO THE SHERPA FAMILY! ON YOUR SOCIALS
AND TAG US IN YOUR A ON YOUR SOCIALS AND TAG US IN YOUR A
MAKE SURE TO FOLLOW USMAKE SURE TO FOLLOW ADVENTURES.DVENTURES.
All products built and designed by Sherpa Equipment Company are intended for off-road use and should be assembled, installed, and used according to Sherpa Equipment Company’s recommendations. Sherpa Equipment Company’s products should be used safely with good judgment towards others and surroundings.
By installing Sherpa Equipment Company’s products on your vehicle you assume all liability. Sherpa Equipment Company will not be held liable for damages or loss associated with the installation or use of its products. It is recommended that you inspect your roof rack within the first 100 miles of installation and every 500 miles after.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>