AIO360TB ZEB AIO Cooler Fans User Manual

Table of Contents

Thank you for purchasing the ZEB- AIO360TB/W AlO Cooler. Please read this user manual carefully and keep it for future reference.
Note

Avoid the usage of this product in the high temperature and high humidity environments.
Avoid the self-disassembly of the products or it results in the voiding of the product’s Warranty.
Please wipe the existing thermal compound that is present on the CPU and install the Included thermal compound to obtain the best Cooling efficiency.
To learn more about the Terms and conditions for the warranty policy, please visit https://zebronics.com/pages/warranty-policy

Form Factor of the AIO Cooler: 360mm CPU Socket
Supported CPU Models

Intel: LGA 115X / 1200 / 1366 / 1700 / 2011 / 2066
AMD : FM3 / FM2 / FM1 / AM2 / AM2+ / AM3 / AM3+ / AM4 / AM5
Fan Specs No. of Cooling Fans Included : 3 x 120mm
Power Consumption: 2.16W
Noise Level: 15-35db
MTBF: 30000 Hours
Airflow Rate : 67.96 CFM
Speed: 1800RPM (Max.)
Support: ARGB Sync
Power Connector : 4-Pin | Length: 50cm
LED Connector: 3-Pin | Length : 52cm
Fan Dimensions : 12 × 12 × 2.5 cm (Wx Dx H)
Pump Specs Rated Voltage / Current : 12V / 0.3A
Power Consumption : 3.6W
Noise Level: 30db
MTBF : 30000 Hours
Speed: 2500 RPM (Max.)
Tube Type: Braided Rubber Pipe
Tube Length: 38cm
Tube Diameter : 1.2cm
Power Connector: 3-Pin | Length: 32cm
LED Connector: 3-Pin | Length: 47.5cm
Pump USB: 4-Pin | Length: 74cm
Dimensions : 9.5 × 9 x 5.2cm (WXDX H)
Radiator Specs Material of the Heat Sink : Aluminium
Material of the Heat Transfer Pipe : Aluminium
Dimensions : 39.5 × 12 x 2.7 cm (WxDXH)
Product Weight: 1.4 Kg

For INTEL SETUP

Applying the Thermal Paste

Step 1: Remove the existing Thermal compound which is present on the CPU.
Step 2: Apply the included thermal paste on the CPU as per your CPU requirement.
Step3: Using the included Thermal paste spreader, Spread the applied thermal paste evenly on the surface of the CPU.
Step4: Wipe of the excess Thermal compound which is present on the CPU.

Now peel off the protective cover which is present under the conductive plate of the CPU Block.

MOUNTING THE CPU BLOCK For LGA 1700 / LGA 1200 /LGA115X Models

Step 1: Take the included Intel Mounting Backplate(B), Adjust the mounting points according to your motherboard layout. Now align it to the rear side of the motherboard.
Step 2: Align the mounting studs(G3) to the motherboard as shown in the reference image. Fasten the Mounting studs to the Mounting bracket which is placed on the rear side of the motherboard.
Step 3: Align the CPU block to the mounting studs(G3) (as shown in the reference image).
Step4 : Align the mounting Nuts(Gl) to the CPU block (as shown in the reference image).
Step 5 : Using the required tools. Fasten the Mounting nuts(Gl) along with the CPU block to the mounting Studs(G3) which is placed on the motherboard.

Step l: Take the included Intel Mounting Backplate(B), and adjust the mounting points according to your motherboard layout. Now align it to the rear side of the motherboard.
Step 2: Align the CPU block to the motherboard (as shown in the reference image).
Step 3 : Align the mounting Screws(G4) to the CPU block (as shown in the reference image).
Step 4: Using the required tools. Fasten the Mounting screws(G4) along with the CPU block to the mounting bracket(B) which is placed on the rear side of the motherboard.

Step 1 : Combine the 4-pin fa n connector of the AIO cooler together and Plug the combined 4-pin Fan connector into the System fan header of the motherboard.
Step 2: Combine the 3-pin ARGB fan connector and 3-pin ARGB CPU Block connector. Now plug the Combined ARGB connector to the 3-pin connector to the ARGB header of the Motherboard.
Step 3: Connect the Power connector CPU Block connector to the CPU Fan He ader which is present on the motherboard.
Step 4: Connect the USB connector to the USB 2.0 Header on the motherboard.

Step1: Align the Radiator block of the AIO cooler to the mounting points of the Gaming cabinet.
Step 2: Place the mounting screws on the mounting points of the AIO cooler.
Step 3: By using the required tools, Fasten the mounting screws to the AIO cooler via the cabinet. Ensure to apply pressure evenly for optimal placement.

For AMD SETUP
Combining the CPU Mounting Brackets

Step 1 : Align the AMD mounting brackets (D) To the CPU mounting points of the motherboards.
Step 2 : Align the AMD mounting screws (G2). To the mounting points of the motherboard.
Step 3: Using the required tools, Fasten the AM D mounting screws to the mounting points of the motherboard via the AMD mounting plate (as shown in the Reference image).

Applying the Thermal Paste

Steps1: Remove the existing Thermal compound which is present on the CPU
Step 2: Apply the included thermal paste on the CPU as per your CPU requirement.
Step 3: Using the included Thermal paste spreader, Spread the applied thermal paste evenly on the surface of the CPU.
Step 4: Wipe off the excess Thermal compound that is present on the CPU. Now peel off the protective cover which is present under the conductive plate of the CPU Block.

Mounting CPU Block

Step l: Align the intel screw stud to the mounting points of the AMD Mounting Bracket and fasten the mounting stud to the mounting points of theAMD bracket.
Step 2 : Align the CPU block to the Intel screw studs. Now place the CPU block on the CPU via the mounting studs.
Step3 : Now align the Intel mounting Nuts to the Intel screw Stud and Fasten them with even pressure until the CPU block is intact

Connection of AIO Cooler

Step 1 : Combine the 4-pin fa n connector of the AIO cooler together and Plug the combined 4-pin Fan connector to the System fa n header of the motherboard.
Step 2 : Combine the 3-pin ARGB fan connector and 3-pin ARGB CPU Block connector. Now plug the Combined ARGB connector to the 3-pin connector to the ARGB header of the Motherboard.
Step 3 : Connect the Power connector CPU Block connector to the CPU Fan Header which is present on the motherboard.
Step 4 : Connect the USB connector to the USB2.0 Header on the motherboard.

Mounting the AIO Cooler setup

Step 1 : Align the Radiator block of the AIO cooler to the mounting points of the Gaming cabinet.
Step 2 : Place the mounting screws on the mounting points of the AIO cooler.
Step 3 : By using the required tools, Fasten the mounting screws to the AIO cooler via the cabinet. Ensure to apply pressure evenly for optimal placement.

Note: The Image is for mounting reference only Please use a compatible gaming cabinet to mount the AIO cooler.

Connect the AIO’s USB header to the motherboard’s USB 2.0 header & install the Windows software to display the processor’s tern operation.

We suggest you to visit our Below link to buy the optimal Gaming chassis for your AIO Cooler.
https://zebronics.com/collections/premium-gaming-chassis