Myplus AS-G01 Air Conduction Bluetooth Headset Instruction Manual

Myplus AS-G01 Air Conduction Bluetooth Headset

Manual Instruction for
Air Conduction
Wireless Headphones

Summary of button functions

1. On/Off/Volume Up/PreviouS/Play/Pause/Answer/Jng up/ reject calls/voice assistant
2. Volume decrease/next track
3.  Magnetic charging port
4. Speaker
5. LED indicator

Controls

• On: Press and hold the power button for 5 seconds in the shutdown state to turn on the device. The blue LED light will stay on for 1 second, and the prompt tone will sounder on

• Off: The headphones are in the power on state. Press and hold the power on button for 5 seconds, and the LED red light will stay on fo 1 second to turn oft. The prompt tone ewer oft plugging in the charging cable

• Connect  BT: When the headphone is in power-off state, press and hold it for 5 seconds to enter a pairing state with red and blue LEDs flickering and reminding tone: pairing. After the device (smart phone, tablet computer, etc.) search, press it to connect.  Connected successfully: When the earphone is successfully connected to the device, the earphone prompt tone is; connected; LED light off

• Play/pause: Click the power button to pause and then click the power button to play music when connected to BI;

• Vol+: Double click on the power button, the loudest sound will be a beep:

• (Call volume defaults to 100%) Vol-: Double click the volume decrease button, the minimum sound will sound like a ding prompt
  Next song: Long press the power button for 2 seconds when music is playing:

• Previous song: Long press the Vol- button for 2 seconds when music is playing:

• Answer/hang up: In the incoming call state: click the power button to answer, long press the power button for 2 seconds to reject the call. In the call state, click the power button to hang up: Voice assistant: Keep BT link, and triple click the power button to turn on the voice assistant, then triple click it again to exit.

• Reset: After plugging the charging line, the headphone will be reset and powered off for charging.

• Clear pairing information:When using a charging cable, plug the headphones into a USB power source, and the ED indicator light will turn red when charging. The indicator light will turn off when fully charged clear the pairing information, and then enter the pairing mode. Red and Blue light blinks 1 second spontaneously.

• Charging: In case of using charging line for charging, connect the headphone with the USB power. During the charging, LED turns red. After charging, the LED turns blue.

• Over-range entry pairing: The headset is out of range of Bluetooth, the headset indicates that the connection is disconnected, the headset tone:

• Disconnected pairing: Led indicator red and blue lights flashing, the headset enters the back-to-connect state, the back-to-back state is maintained for 300 seconds (during the period to return to the range to connect to Bluetooth), no connection after 300 seconds to shut down:

• DUT mode: After power on, 5 click the power button in pairing mode, blue light flash, charging or manual shutdown exit;

Specifications

• Bluetooth pairing name: AS-CO 1
• Bluetooth version: Bluetooth 5.3
• Bluetooth chip: AC7006F4
• Supported protocols: HFP/A20P/AVRCP Coonectloo distance: ?:12 meters
• Battery type: 80mAh polymer battery
• Music playback time: about 6 hours (100% volume)
• Talk time: about 5 hours (100% volume)
• Charging time: 1.5 hours
• Speaker specification; 15.4MM.t0.05
• Speaker Impedance; 320±15%
• MIC sensitivity: -38t2db

How to wear

Attention

• Listening to music for an excessive long time make you feel uncomfortable, please try to use a medium volume instead of a big one.
• No matter how the volume is, please do not make it prevent you from hearing the surrounding sounds. Please take care when using the headphone..
• Do not throw, press the headphone or put it in the water.
• The headphone should keep away from fire, water and high voltage devices.
• It is not for children’s use as it contains small parts.
• Please do not treat it as domestic waste. Instead, send it to your electrical and electronic recycling station. If there is any injury or property loss due to violation of the above contents, we will not bear any responsibility.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
  • Reorient or relocate the receiving antenna.
  • increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer  an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>