rosenbauer Safe Grip 3 Firefighter Gloves Instruction Manual

SAFE GRIP 3
User information

Safe Grip 3 Firefighter Gloves

USER INFORMATION
SAFE GRIP 3 AND SAFE GRIP 3S
PROTECTIVE GLOVES FOR FIRE FIGHTERS

Approved in accordance with EN 659:2003 + A1:2008
You have made an excellent choice!
Congratulations on your purchase of quality gloves from Rosenbauer. Premium quality, hand-picked materials combined with state-of-the-art design, crafted with the utmost of care, guarantee protection and perfect wearing comfort for professional fire fighters.

USE

The contractually guaranteed scope of protection of the respective personal protective equipment results from the relevant provisions of the PPE Regulation (EU) 2016/425 and the standards derived from it in accordance with the declaration of conformity. Any further protection does not exist. Additional dangers such as chemical, biological, electrical or radioactive hazards must be covered by another and/or additional protective equipment.
At this point we would like to point out that the user of this PPE must carry out a risk assessment before use. The user determines through this risk assessment what risk he will have to expect in his operations. The real risk arises from the
extent to which various hazards are likely in relation to the severity of the consequences for the user in such an exposure. The resulting risk assessment is the basis for the selection and application of an adequate protective equipment (with the appropriate protection level if applicable).
Please make sure that your Rosenbauer PPE meets the requirements of your risk assessment with regard to the contractually guaranteed protective effect.
Fire brigade gloves are part of a fire-fighter’s personal protection. They can be used during technical and fire emergencies.

• Excellent touch sensitivity – optimal passform
• Three-dimensional, ergonomic design
• Excellent heat and cold protection
• Abrasion, puncture and cut resistant
• Slip proof also with smooth and wet surfaces
• Watertight, windproof and breathable
• Modern design

Pictograms and performance levels according to EN 659:2003 + A1:2008 standard

Abrasion resistance – EN 388 | 3 (2000 cycles)| 4
---|---
Cut resistance – EN 388 | 2 (factor 2.5)| 4
Tear resistance – EN 388 | 3 (50N)| 4
Puncture resistance – EN 388 | 3 (100N)| 3
Dexterity – EN 420 | 1| 4
Burning behavior – EN 407| 4
Cut resistance – EN ISO 13997| D

All further paremeters = passed
1 or A = low performance level. 4, 5 or F = high performance level.

Contact heat resistance – EN 702|
---|---
Convective heat resistance -EN 367 /407|
Radiant heat resistance – EN ISO 6942|
Shrinkage – ISO 17493|
Removal of gloves – EN ISO 15383|
Water permeabilty – EN 344-1|
Fluid permeability – ISO 15383|
Chemical permeability – EN 368|

Please note that the firefighting glove SAFE GRIP 3 alone, without an additional inner glove, was the subject of the type examination and corresponds only in this application to the standards of the declaration conformity.
An additional inner glove may have a negative impact on the protection and the wearing properties of the firefighting glove SAFE GRIP 3 and is therefore not permitted.
LIMITATIONS TO USE
The protective glove should be checked for damage following subjection to high mechanical, chemical or thermal loads. Water-tight and breathable laminated membrane, but avoid damage to the membrane due to tearing.

Penetrative abrasion or surface damage due to heat, or chemicals, etc. can have a negative effect on protection levels. It is essential that protective gloves showing such, or similar, damage are discarded.
The gloves do not offer protection against chemical and electrical hazards, or bacteria. The gloves remain impervious to water for as long as the membrane is undamaged.

STORAGE

The protective gloves should be dry stored in normal room atmosphere.
CLEANING/CARE
The gloves are washable. Hand washing recommended. Gloves can be washed at temperatures of up to 60° to remove severe contamination. Surface dirt can be removed by brushing. Do not use bleaches or oxidising agents!

MATERIAL COMPOSITION

OUTER LAYER

• Back of the hand made of high-quality NOMEX® III with a para aramid non woven laminated onto the backside for heat and cut protection, gathered elastic cuffs. Reflective piping for enhanced safety during night- time service.
• CARBON/SILICONE palm area, mineral, coated double- faced product made from NOMEX® and para aramid for excellent fit, very high abrasion resistance and first glass grip even on smooth and wet surfaces.
• Cuff: NOMEX® Ill yellow/silver/yellow 3M® reflecting strips

MOISTURE BARRIER

Water-tight and breathable thanks to GORE-TEX® with GORE® GRIP technology.
INNER LINING

Knitwear made of 100 % para aramid, NOMEX® fabric in the cuff

DESIGN

• Heat and impact protection on rear of hand
• Holding ring and hook
• Color: dark blue or sand yellow

SIZES

The protective gloves are available in the following sizes:

CONFORMITY DECLARATION
Subject of the declaration is the following personal protective equipment (PPE):

SAFE GRIP 3
SAFE GRIP 3 S| Art. No.:
Art. No.:|   dark blue
142750
142740| sand yellow
142760
---|---|---|---

The Manufacturer:

Rosenbauer International AG
Paschingerstraße 90
4060 Leonding / AUSTRIA

This statement is issued under the sole responsibility of the manufacturer.
The subject of the declaration (PPE described above) complies with the relevant Union harmonsisation legislation:
Regulation (EU) 2016/425 personal protective equipment.
Conformity is achieved by complying with the applicable requirements of the following documents:
EN 659:2003+A1:2008+AC:2009 Protective gloves for firefighters
The notified body
ÖTI – Institute for Ecology, Technology and Innovation GmbH (ID-No.: 0534)
Siebenhirtenstr. 12A, A-1230 Vienna, has carried out the EU type examination (modul B)
and issued the EU type examination certificate no. VN620 225467
The PPE is subject to the following conformity assessment procedure:
For category III: Conformity with the model based on internal production control with supervised product checks at irregular intervals (module C2) under surveillance of the notified body ÖTI – Institute for Ecology, Technology and Innovation, ID-No: 0534
Signed for the manufacturer / Place and date of issue

Leonding, 01.09.2023

Rosenbauer International AG
Paschinger Straße 90
4060 Leonding, Austria
Tel.: +43 732 6794-0
Fax: +43 732 6794 -77
office@rosenbauer.com
www.rosenbauer.com
Text and illustrations are not binding. The illustrations may show optional extras only available at extra charge.
ROSENBAUER retains the right to alter specifications and dimensions given here in without prior notice.

References

• Feuerwehrfahrzeuge | Feuerwehrfahrzeughersteller - Rosenbauer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>