Sage SCG600 Coffee Grinder Machine User Guide
- June 3, 2024
- Sage
Table of Contents
Sage SCG600 Coffee Grinder Machine
SAGE® RECOMMENDS SAFETY FIRST
At Sage® we are very safety conscious. We design and manufacture appliances with your safety foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE
-
A downloadable version of this document is also available at sageappliances.com
-
Before using the first time ensure your electricity supply is the same as shown on the label on the underside of the appliance.
-
Remove and safely discard any packaging materials before first use.
-
To eliminate a choking hazard for young children, safely discard the protective cover fitted to the power plug.
-
This appliance is for household use only. Do not use the appliance for anything other than its intended use. Do not use in moving vehicles or boats.
Do not use outdoors. Misuse may cause injury. -
Fully unwind the power cord before operating.
-
Position the appliance on a stable, heat resistant, level, dry surface away from the edge and do not operate on or near a heat source such as a hot plate, oven or gas hob.
-
Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.
-
Do not leave the appliance unattended when in use.
-
Always ensure the appliance is turned OFF, unplugged at the power outlet and has been allowed to cool before cleaning, attempting to move or storing.
-
Always turn the appliance to the OFF position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use.
-
Do not use the appliance if the power cord, plug, or appliance becomes damaged in any way.
If damaged and maintenance other than cleaning is required please contact Sage Customer Service or go to sageappliances.com -
Any maintenance other than cleaning should be performed by an authorised Sage® service centre.
-
Children should not play with the appliance.
-
Cleaning of the appliance should not be carried out by children unless they are 8 years or older and supervised.
-
The appliance and its cord should be kept out of reach of children aged 8 years and younger.
-
The installation of a residual current safety switch is recommended to provide additional safety when using all electrical appliances. Safety switches with a rated operating current not more than 30mA are recommended.
Consult an electrician for professional advice. -
Do not use attachments other than those provided with the appliance.
-
Do not attempt to operate the appliance by any method other than those described in this booklet.
-
Do not move the appliance whilst in operation.
-
Do not touch hot surfaces. Allow the appliance to cool down before moving or cleaning any parts.
-
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
-
This appliance can be used by persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge, only if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Do not operate the grinder without the hopper lid in position. Keep fingers, hands, hair, clothing and utensils away from the hopper during operation.
The symbol shown indicates that this appliance should not be disposed of in
normal household waste. It should be taken to a local authority waste
collection centre designated for this purpose or to a dealer providing this
service. For more information, please contact your local council office.
To protect against electric shock, do not immerse the power plug, cord or
appliance in water or any liquid.
GETTING TO KNOW YOUR NEW APPLIANCE
A. Bean Hopper Lid
B. Bean Hopper
C. Hardened Stainless Steel Conical Burrs.
Removable and Adjustable Upper Burr
D. Grind Size Collar
E. GRIND TIME Dial
F. START / CANCEL Button
G. Grind Outlet
H. 50mm blade
I. Grind Tray
ACCESSORIES
J. Adjustable Razor™ Dose Trimming Tool
K. Portafilter Cradle 50–54mm
L. Portafilter Cradle 58mm
OPERATING YOUR NEW APPLIANCE
BEFORE FIRST USE
Remove and safely discard all promotional labels and packing materials
attached to your Sage® appliance. Wash hopper, and cradles in warm soapy water
and dry thoroughly. Wipe exterior of grinder with a soft damp cloth and dry
thoroughly. Place grinder on fl at level surface and plug power cord into
220-240V outlet and switch Power ‘ON’.
ASSEMBLING YOUR SAGE CONTROL DOSE™ PRO
Bean Hopper
Align tabs on the base of the bean hopper and insert hopper into position.
Holding the hopper, press down fi rmly and turn the bean hopper dial 45° to
lock into position.
A “click” sound will be heard when the hopper is properly locked in place.
Ensure the hopper and the Grind Size Collar is aligned properly.
Fill with fresh coff ee beans and secure lid on top of bean hopper.
NOTE
If the bean hopper has not been locked into position, the GRIND TIME dial will
not be illuminated.
GRINDING FOR ESPRESSO COFFEE
Use single-wall filter baskets when grinding fresh coffee beans. Use the finer
1–25 settings in the ESPRESSO range
Step 1:
Insert the appropriate portafilter cradle size. Insert your portafilter into
the cradle.
Step 2:
Selecting Grind Amount
Select the desired amount of ground coffee required by turning the GRIND TIME
dial.
Step 3:
Tamping the Ground Coffee
After dosing the portafilter with freshly ground coffee, tamp down with
between 15-20kg of pressure.
Step 4:
Trimming the Dose
The adjustable Razor™ Dose Trimming Tool allows you to trim the puck to the
right level for a consistent extraction.
Select the correct width blade of the Razor™ to match the diameter of your fi
lter basket. The Razor™ has three blades of varying widths: 58mm, 54mm and
50mm. The 58mm and 54mm are already fitted within the Razor™ body. The 50mm is
separate.
If you require the 50mm blade, turn the adjustment dial past #1 until the 54mm
blade is fully extended and able to be pulled from the body.
If you require the 50mm blade, turn the Adjustable Dial past #1 until the 54mm blade is fully extended and able to be pulled from the body.
NOTE
The Adjustable Dial may feel tight as you continue to wind it towards the end
of its travel.
Insert the 50mm blade into the body. Wind the Adjustable Dial until the blade is retracted past #4. Press the 50mm and 58mm blades at the same time, towards the centre of the body until a “click” sound can be heard.
Adjust the Razor™ to the setting in the table below for your Sage® espresso machine. This is a starting point for your dose height.
Sage ® Espresso Machine| Portafilter
Size
| Dose Height
---|---|---
Model name starting with “SES9”| 58mm| 2
Model name starting with “SES8”| 54mm| 2.5
After tamping the coffee, insert the Razor™ into the filter basket until it
rests on the rim of the basket. The blade of the dosing tool should penetrate
the surface of the tamped coffee. If the blade does not penetrate the surface
of the tamped coffee, your coffee is underdosed. Increase the amount of dosed
coffee by adjusting the GRIND TIME dial.
Rotate the Razor™ back and forth while holding the portafilter on an angle
over the knock box to trim off a little excess coffee.
Step 5:
Select Your Grind Size
For espresso, we recommend starting with grind size setting 15 and rotating
the Hopper (to adjust the Grind Size Collar) either coarser or finer.
NOTE
If the Grind Size Collar is tight, run the grinder by pressing the START /
CANCEL button while turning the Hopper. This will release coff ee grounds
caught between the burrs.
GRINDING INTO A GRINDS CONTAINER OR COFFEE FILTER
Step 1:
Remove cradle by sliding out from under the grind outlet.
Place your container or coffee filter directly under grind outlet.
Step 2:
Select the required amount of ground coffee by rotating the GRIND TIME dial.
Step 3:
Select Your Grind Size
Rotate the Hopper to adjust the Grind Size Collar until it reaches the
required brewing method range.
FEATURES OF YOUR SAGE DOSE CONTROL™ PRO
Pause Function
You can pause the grinder during operation, allowing you to collapse or settle
the coff ee in the Portafi lter.
-
Press the START / CANCEL button to start the grinding operation.
-
During grinding, press the START / CANCEL button to pause the grinding operation for up to 10 seconds.
The START / CANCEL button will slowly fl ash while paused. -
Press START / CANCEL again within this time to resume grinding the remaining dose.
Or press and hold the START / CANCEL button for 1 second to cancel.
Manual
Grinding manually allows you to have complete control over how much coff ee is
dispensed.
- Press and hold the START / CANCEL button to grind for as long as you require.
- Release START / CANCEL button to stop grinding.
COFFEE CHART *****
Brewing Method| Espresso| Percolator| Drip| French Press or Plunger
Grind Size| Fine| Medium| Medium Coarse| Coarse
Grind Setting| 1-25| 26-34| 35-45| 46-55
Amount (Shot / Cup)| 6 secs per shot
10 secs per 2 shots
| 3 secs per cup| 3 secs per cup| 2 secs per cup
*This coffee chart should be used as starting point to adjust your grind time and/or size, as both may vary when using different coffee bean types, age and degrees of roast.
ADJUSTING CONICAL BURRS
Some types of coffee may require a wider grind range to achieve an ideal
extraction or brew.
A feature of your Dose Control™ Pro is the ability to extend this range with
an adjustable upper burr.
- Unlock hoppe
- Hold hopper over container & turn dial to release beans into container
- Align hopper into position
- Run grinder until empty
- Remove hopper
- Remove upper burr
- Remove wire handle from both sides of the burr
- Default setting is 6
- Move adjustable top burr, 1 number, coarser or finer
- Align the number with the handle opening
- Insert wire handle from both sides of the burr
- Push upper burr firmly into position
- Lock upper burr
- Align hopper into position
- Press down firmly & rotate to lock into position
- Check your extraction
CARE, CLEANING & STORAGE
- Empty beans from the hopper and grind out any excess beans (see below).
- Unplug power cord from power outlet before cleaning.
- Wash the hopper lid and bean hopper in warm soapy water, rinse and dry thoroughly.
- Wipe and polish exterior of appliance with a soft damp cloth.
NOTE
Do not use alkaline or abrasive cleaning agents, steel wool scouring pads, as
these can damage the surface.
NOTE
Please do not clean any grinder parts or accessories in the dishwasher
CLEANING CONICAL BURRS
Regular cleaning helps the burrs achieve consistent grinding results which is especially important when grinding for espresso coffee.
- Unlock hoppe
- Hold hopper over container & turn dial to release beans into container
- Align hopper into position
- Run grinder until empty
- Remove hopper
- Remove upper burr
- Clean upper burr with a brush
- Clean lower burr with cleaning brush
- Clean grind outlet with brush
- Push upper burr firmly into position
- Lock upper burr
- Align hopper into position
- Lock hopper
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | WHAT TO DO |
|---|
Grinder does not start after pressing
START / CANCEL
button
| • Grinder not plugged in.
• Bean hopper not attached correctly.
• Grinder has overheated.
• GRIND TIME dial is on 0 seconds.
| • Plug power cord into power outlet.
• Lock bean hopper into position. Refer to the Bean Hopper section on page 6.
• Leave for 20 minutes to cool down before using again.
• Rotate the GRIND TIME dial to increase grind time.
Motor starts but no ground coffee coming from grind outlet| • No coffee beans in
bean hopper.
• Grinder / bean hopper is blocked.
| • Fill bean hopper with fresh
coffee beans.
• Remove bean hopper. Inspect bean hopper and burrs for blockage. Refer to the Cleaning Conical Burrs section on page 10.
Can’t adjust the Grind Size Collar| • Grind Size Collar too tight.
• Coffee beans and grinds
caught in the burrs.
• Hopper not installed correctly.
| • Rotate the Bean Hopper to turn the Grind Size Collar to adjust grind settings.
• Run the grinder by pressing the START / CANCEL button while turning the Hopper.
• Unlock the hopper and install as per instruction. Refer to the Bean Hopper section on page 6.
Unable to lock bean hopper into position| • Coffee beans obstructing bean
hopper locking device.
| • Remove bean hopper. Clear coffee beans from top of burrs. Re-lock the
hopper into position & try again.
Not enough / too
much coffee grind
| • Grind amount requires adjustment.| • Use GRIND TIME dial to fine tune the
amount more or less.
Portafilter overfills| | • It is normal for the correct amount of
coffee to appear overfilled in your portafilter. Untamped coffee has
approximately three times the volume of tamped coffee.
Emergency stop?| | • Press the START / CANCEL button to pause
operation.
• Unplug power cord from power outlet.
GUARANTEE
2 YEAR LIMITED GUARANTEE
Sage Appliances guarantees this product for domestic use in specified
territories for 2 years from the date of purchase against defects caused by
faulty workmanship and materials. During this guarantee period Sage Appliances
will repair, replace, or refund any defective product (at the sole discretion
of Sage Appliances).
All legal warranty rights under applicable national legislation will be
respected and will not be impaired by our guarantee. For full terms and
conditions on the guarantee, as well as instructions on how to make a claim,
please visit www.sageappliances.com.
Sage Appliances GmbH
Campus Fichtenhain 48, 47807 Krefeld, Deutschland
Deutschland: +49 (0)8005053104
Österreich: +43 (0)800 80 2551
Belgium
+32 (0)800 54 155
Luxembourg
+352 (0)800 880 72
Spain
+34 (0)900 838 534
Due to continued product improvement, the products illustrated or photographed in this document may vary slightly from the actual product.
Registered in Germany No. HRB 81309 (AG Düsseldorf).
Registered in England & Wales No. 8223512
http://www.sageappliances.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>