FRIGIDAIRE GLDB958JB0 Dishwasher Repair Instruction Manual

: July 31, 2024
: Frigidaire

Table of Contents

GLDB958JB0 Dishwasher Repair
Product Information
Specifications:
- Product Usage Instructions
Installation Instructions:
Safety Precautions:
Owner’s Manual:
- FAQ
Q: Where can I find genuine replacement parts for the
Q: What should I do if I encounter an electric shock hazard

GLDB958JB0 Dishwasher Repair

“`html

Product Information

Specifications:

Brand: Frigidaire
Model: GLDB958JB0
Product Type: Dishwasher
Country of Origin: United States

Product Usage Instructions

Installation Instructions:

Disconnect electrical power at the fuse box or circuit breaker
box before beginning installation to avoid electric shock
hazards.
Ensure you have all the necessary parts for installation.
Remove the kickplate assembly by unscrewing the two screws at
the front using a #2 Phillips screwdriver.
Follow the specific anchoring instructions if required,
available at plumbing supply or hardware stores.

Safety Precautions:

Read all instructions before installing the dishwasher.
Do not use the dishwasher until it is completely installed to
avoid tip-over hazards.
Avoid pushing down on the open door of the dishwasher.

Owner’s Manual:

Make sure to read the dishwasher’s Use and Care Manual provided
by the owner. It contains essential safety information and
suggestions for optimal performance.

FAQ

Q: Where can I find genuine replacement parts for the

Frigidaire GLDB958JB0 dishwasher?

A: Genuine replacement parts for this dishwasher can be found at
Appliance Factory Parts.

Q: What should I do if I encounter an electric shock hazard

during installation?

A: Immediately disconnect electrical power at the fuse box or
circuit breaker box and seek professional assistance to address the
issue.

“`

This Owner’s Manual is provided and hosted by Appliance Factory Parts.
FRIGIDAIRE GLDB958JB0 Owner’s Manual
Shop genuine replacement parts for FRIGIDAIRE GLDB958JB0
Find Your FRIGIDAIRE Dishwasher Parts – Select From 369 Models ——– Manual continues below ——–

Dishwasher
Installation Instructions

Parts You Will Need* (NotIncluded)
· Drain Hose Clamp, 11/4″Diameter · Elbow, 90 ° with a 3/g, National Pipe Thread · Strain Relief Bushing · Wire Nuts, two (2) for 12-14 gauge wire

_r
If required:
· “Y” Branch Tailpiece and Connector Kit (See Step 4)
· Air Gap Kit (See Step 4) · Fasteners for floor
anchoring (See Step 9)

Available at: Plumbing Supply
Plumbing Supply Hardware Store

Electric Shock Hazard
Disconnect electrical power at the fuse bo circuit breaker box before beginning insta Failure to follow this warning could result or serious injury.

INSTALLER: Leave Installation Instructions with owner.
OWNER: Read your dishwasher Use and Care Manual. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher.

Printed in U.S.A.

154373601
(1/00)

Read all instructions before installing dishwasher.
For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher.

· Examine dishwasher and locate connections. See
· Locate dishwasher where there is easy access to d and electrical lines. The best location is on either s kitchen sink for access to existing plumbing and e loading dishes. See Step 4.
· Electrical, water, and drain connections are not the all age, brands, or models of dishwashers. Check t and length of home utilities. See Step 4.
· A 15-20 amp, grounded, 120 volt AC only, electrical required. See Steps 4 and 8.
· If dishwasher drain hose will be connected to a foo for the first time, knock out plug located inside disp See Steps 4 and 6.
· Kinked water or drain hoses can cause problems. remove drain hose from tub attachment. See Step
· Dishwashers need to be connected to a hot water s enough water pressure to insure an adequate fill. See Steps 4 and 7.
· Each home installation differs. You will need addit listed above to complete your installation. See Steps 4 and 7.
· Flush water line prior to making the final connection prevent clogging of dishwasher’s filter screen. See
· The dishwasher will look, sound, and perform best properly leveled. See Step 5. (NOTE: If levelers ar during installation, make sure the floor is flat and f obstruction.)
· Anchor the dishwasher to countertop. See Step 9.

Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door.

1. Remove two (2) screws at front of the kickplate asse a #2 Phillips screw driver.