Kopp SY-WL-G-01 Rechargeable LED Work Light Instruction Manual

July 31, 2024
Kopp

Kopp SY-WL-G-01 Rechargeable LED Work Light

INSTRUCTION MANUAL

You have chosen a high-quality work light that has been manufactured with great care. The light features an on/off switch/dimmer, a charging socket, a magnet, charging indicator, LEDs, rotatable hook, and a USB charging cable.

OVERVIEW

Technical Data

  • Type: SY-WL-G-01
  • Wattage: 3 W
  • LEDS: COB
  • Rechargeable battery: lithium – ion 3.7 V / 2 Ah
  • USB charging input: Micro USB 5 V DC, internally Iimited to 1 A
  • Charging duration: ~ 5.0 h
  • IP class: IP 54
  • Temperature range: -10°C ± 40°C

Introduction

You have chosen a high-quality product that has been manufactured with the greatest care.

Safety information

  • Carefully read these operating instructions before using the device.
  • Do not use the light if it is damaged.
  • In this case, contact an electrician or refer to the specified service address.
  • Do not look directly into the light. Never open the device.
  • To charge the batteries, only use a certified USB power supply unit.

Commissioning

  • When using the device for the first time, completely discharge and recharge the rechargeable battery once.
  • Switch at back: Light sequence: 100% – 50% – off.
  • The product can not be used during charging.
  • In cases of extended non-use, charge the rechargeable every 3 months.

Control Elements

1. On/off switch/dimmer front
2. Charging socket Micro — USB
3. Magnet
4. Charging indicator
5. LEDs
6. Rotatable hook
7. USB charging cable / Micro — USB

Charging

  • Charge your battery using the supplied USB cable only.
  • Exclusively use a certified USB power source ( e . g . charging device , computer) with a maximum of 5 V output voltage.
  • Connection : USB source — USB charging cable 7 — charging socket 2
  • Open the Iock at the bottom by turning it counter – clock – wise.

The USB charging connection is located underneath.

  • During charging , the charging indicator flashes in blue , it is illuminated in blue when the battery is fully charged.
  • During the charging process , the product is not IP54 -compliant (dust-protected and protected against splashing water)

Product cleaning

We recommend that you use only a damp cloth to clean your work light. Please note that some chemicals used in cleaning agents may damage the diffuser and in no circumstances should you use any such products.

Disposal

As a consumer, you are legally obliged to hand in all waste electrical and electronic equipment as well as batteries and accumulators at a collection point in your municipality or at a retailer so that they can be disposed of in an environmentally sound manner, as otherwise hazards to the environment and human health may arise. Used batteries or accumulators that are not enclosed in the old appliance, as well as lamps that can be removed from the old appliance without destroying it, must first be removed without destroying it and disposed of separately.

Instructions for removing the rechargeable battery The battery can be removed easily and non-destructively by the end consumer or by qualified personnel independent of the manufacturer using commercially available tools. To do this, two screws on the charging socket 2 and two screws under the charging indicator 4 (front and back side) must be removed. The work light can then be opened. The battery inside the work light is additionally protected by a cover. After opening the cover and capping the connection wires, the battery can now be removed.

Declaration of conformity

The declaration of conformity is deposited with the manufacturer.
For further information on disposal or the declaration of conformity, we recommend the Service section on our homepage www.kopp.eu.

Specifications:

  • Type: SY-WL-G-01

  • Wattage: 3 W

  • LEDS: COB

  • Rechargeable battery: lithium-ion 3.7 V / 2 Ah

  • USB charging input: Micro USB 5 V DC, internally limited to 1 A

  • Charging duration: ~ 5.0 h

  • IP class: IP 54

FAQ:

How long does it take to charge the work light?

The charging duration is approximately 5 hours.

Can I use any USB charger to recharge the work light?

It is recommended to use the provided USB charging cable and connect it to a power source with a maximum output voltage of 5 V for optimal charging.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals