pigro felice MODUL’AIR Premium Inflatable Single Floating Hammock User Manual
- July 30, 2024
- pigro felice
Table of Contents
pigro felice MODUL’AIR Premium Inflatable Single Floating Hammock
Specifications
- Armchair: 4 Long Straps
- Lounger: 2 Long Straps, 1 Short Strap
- Sofa: 6 Long Straps, 2 Short Straps
- Double Lounger: 2 Long Straps, 4 Short Straps
Product Usage Instructions
Inflating Instructions
- Locate a clean flat area free of sharp objects.
- Ensure device is firm but not over-inflated.
- Close and secure the inflation valve.
- Maintain adequate air pressure; warm out material before adjusting air pressure.
Maintenance
- Regularly check seams and valves for tears.
- Clean with a garden hose after each use and air dry thoroughly.
- Avoid power hoses, chemicals, or solvents that may damage the device.
Deflating Instructions
- Clean and dry the device completely before deflating.
- Remove accessories if applicable.
- Open all air valves and press to deflate completely.
Folding / Storage
- Fold the device correctly as per the provided instructions.
- Ensure the product is fully dry before packing for storage.
Repair
If the product loses pressure, use the pump to restore air pressure due to
temperature changes.
Product Is Creased
To remove creases, warm up the device, partially deflate, and fully inflate
it a few times.
FAQ
-
Q: How can I prevent bursting when inflating the product?
A: Avoid over-inflation, high-pressure air compressors, and exceeding the recommended working pressure. Fill with cold air only. -
Q: How do I store the product properly?
A: Fold the product correctly, ensuring it is completely dry before packing for storage. -
Q: What should I do if the product loses pressure?
A: Use the pump to restore air pressure as temperature changes may affect the product’s pressure.
USER’S MANUAL
Important safety instructions.
Read all of the instructions and follow them correctly. Keep this manual guide
in a safe place.
Not following these instructions and guidelines may result in drowning or
serious injuries. Pigro Felice® is not liable for any direct, incidental
damages, or personal injuries that may arise out of or connected with the
misuse of its products.
A WARNING
B PROHIBITION
C MANDATORY
- NO PROTECTION AGAINST DORWNING
- DESIGN WORKING PRESSURE: 0.07 BAR
- DALLA COSTA
- DO NOT USE IN OFFSHORE CURRENT
- NOT FOR CHILDREN 14 YEARS OF AGE AND BELOW, APPLY ONLY TO CHILDREN ABOVE 14 YEARS OF AGE
- DO NOT SWIM UNDERNEATH THE STRUCTURE
- DO NOT JUMP OR WALK ON THE DEVICE
- READ INSTRUCTIONS FIRST
- SWIMMERS ONLY
- NUMBER OF USERS, 1 ADULT
- MAX. LOAD CAPACITY 120 KG
BUILDING YOUR MODUL’AIR
Long Straps are used when parts are stacked on top each other.
Short Straps are used when parts are placed next to each other.
WARNING
Do not use this product in over-chlorinated water, excess of chlorine might
lead to color fading, which is not be covered by the warranty. NOTE: This
product should not be placed in a pool where chlorine is being added; the
chlorine level might be too high. This product should not be used before the
chlorine maintenance procedure. Wait at least ONE DAY before using this
product after the chlorine maintenance procedure has been done.
WHEN USING THIS PRODUCT
- Remember that it is for swimmers ONLY. This product is not a toy or a lifesaving device.
- Do not allow jumping and walking onto, or off, the product.
- Do not use in high wind, open water or in dangerous tides.
- Do not use sharp objects while sitting on the product – this could lead to damage.
- Do not exceed the maximum recommended weight capacity of each product.
- Do not use the product if there is leakage or a puncture.
- Do not use for extreme water sport activities.
- Do not use in wreckage areas; this product should only be used on flat surfaces.
- Do not swim underneath the device.
- Use only under competent supervision.
- Keep it away from children who are under the age of 14. MUST BE 14 YEARS OF AGE TO USE.
- Remember that it is made of synthetic material that can melt when exposed to heat or fire. Do not place the product near heating elements, open fire, or other hot objects.
- Do NOT use the pump if the electricity cable is damaged.
- Dry your hands while using the pump to inflate the product. Do NOT use the pump near water.
- Remember that the pump should be used in a clean area, away from sand, water, and grass. When inflating, the unused opening of the pump will suck in air, which will damage the pump; therefore; it is imperative that the pump does not suck in sand, or any other dirt.
- Do NOT exceed the inflation pressure of: 0.07 bar.
- Do NOT attempt to disassemble, repair, or service the pump or the device. The end user cannot maintain the parts of the pump.
INFLATING INSTRUCTIONS
- Locate a clean flat area that is free of stones and other sharp objects.
- After inflating, make sure that the device is firm when touched, but not too hard. CAUTION: To prevent bursting, do not over-inflate or use a high-pressure air compressor; do not exceed the recommended design working pressure. Fill with cold air only.
- Close and recess the inflation valve securely.
- Ensure that adequate air pressure is maintained. After you inflate the furniture, you should allow some time for the material to warm out. Once the product is warmed out, you can pump more air to restore an optimal air pressure. As a result the creases, due to folding, will disappear.
MAINTENANCE
- Check the seams and valves regularly for tears.
- Clean the device after each use with a garden hose; air dry thoroughly before storing the item.
- Do NOT attempt to clean with a power hose.
- Do NOT use chemicals or solvents that may damage the device.
DEFLATING INSTRUCTIONS
- Ensure the device is thoroughly clean and dry before deflating. IMPORTANT: Please read the maintenance section.
- Remove all accessories if applicable.
- Open all air valves and deflate the device completely by pressing on the small valve knob and twisting it 90°. You also have the option to use the reverse mode on the pump to fully deflate the product.
- Close the valve after the air is emptied from the product.
FOLDING / STORAGE
- Fold the device properly; to do so, follow the drawing below. TO START ALWAYS POSITION THE AIR VALVE FACING THE FLOOR
HH TOP - Do not pack the product when wet; make sure the product has dried out completely before packing.
- Store the product in a clean place – that is indoors – at a room temperature between 10°C (33 F), and 40°C (105 F); this can affect its functioning, which is not be covered under the warranty.
REPAIR
Leak In The Device
The device comes with a repair patch. If you have an idea where the leak is,
place a mixture of dishwashing liquid and water into a spray bottle and spray
over the suspicious areas. Any leak will produce bubbles that will pinpoint
the location of the leak. Thoroughly clean the area surrounding the leak to
remove any dirt or grime.
Use the provided repair patch to overlap the damaged area by approximately 1.5
cm (1/2”). Round off the edges and place the patch on the damaged area and
press down firmly. You may want to place a weight on top to keep the patch in
place. Do NOT inflate the device immediately after patching; wait at least one
hour.
If the patch does not hold, you can purchase silicon or polyurethane based
glue; the same glue that is used for repairing camping mats, tents, or shoes.
This product can be found in your local shop or market. Use it to patch the
device. Before doing so, please refer to the instructions on glue and
patching.
Device Not Inflating
- Always check to ensure that the hose is connected to the pump at AIR IN, inflating, and not to AIR OUT. The AIR OUT connection is used to suck the product vacuum.
- When inflating, if air leaks from the nozzle, check to see if the nozzle is attached properly.
- If you use the product for long periods of time, there is a possibility that the chair
will start losing pressure after a while. This is normal. The air pressure in the product fluctuates due to temperature changes. You can use the pump to restore air pressure in the product.
Pump No t Working
Check to see if there is voltage on the socket by plugging in a different
electrical appliance. If the pump is plugged in, and the switch is turned on,
the pump should be working. If this is not the case, contact the Pigro Felice®
Customer Service.
Product Is Creased
Due to the fact the the product is inflatable, it will only reach the optimal
form some time after it has been inflated. After unpacking and inflating, the
product might be a bit creased; the product has been folded to take up less
space once it has passed production. If you allow the device to warm up,
partially deflate, and then fully inflate it a few times in the course of a
few hours, the creases will disappear.
Pigro Felice® Customer Support:
hello@pigrofelice.com
WARRANTY
Pigro Felice® guarantees the Pigro Felice® devices and pump to be free from material and workmanship defects for a period of one (1) year from the date of its purchase by the customer. If, during this warranty period, the product proves defective due to improper materials or workmanship, please contact Pigro Felice®. Pigro Felice® will repair or replace the product based on the terms and conditions set out below, provided that the product has been used for the purposes outlined in these manuals, and operated according to all instructions provided.
CONDITIONS
- The warranty will only be granted when the original invoice or sales receipt (must indicate the date of purchase and dealer’s name) is presented, along with pictures of the defective product. Pigro Felice® reserves the right to refuse the warranty of service if the above documents cannot be presented, or if the information contained in them is incomplete or ineligible.
- This warranty will not reimburse, or cover the damage or modification that is a result of adaptations or adjustments that have been made to the product, without prior, written consent from Pigro Felice®.
- This warranty covers none of the following:
- Periodic maintenance, repair or replacement of parts due to normal wear and tear;
- Any adaptation or changes to upgrade the product from its normal purpose as described in the instruction manual, without prior written content from Pigro Felice®;
- Transport costs, and all risks associated with transport relating directly or indirectly to the warranty of the product;
- Damage resulting from:
- Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Pigro Felice®’s instructions on the proper use and maintenance, (b) installation or use of the product in a manner that is inconsistent with the technical or safety standards set by the country where it is used and (c) improper or incorrect installation of the product;
- Repairs done by parties other than those approved by the Pigro Felice® staff or the customer himself;
- Accidents, lightning, over-chlorinated water, fire, or any other cause that is beyond Pigro Felice®’s control.
- This warranty does not affect the customer’s statutory rights under applicable national laws that are currently enforced, or the customer’s rights against the dealer arising from their sale/purchase contract. All customers must obtain authorization from Pigro Felice® before returning a defective product.
CONTACT
The Pigro Felice® Customer Service Department can be reached using the
following information:
Pigro Felice® Customer Service
hello@pigrofelice.com
www.pigrofelice.com
ENVIRONMENTAL PROTECTIONS
Pigro Felice® is compliant with:
EN 71 standard
Flame Retardant 3PHR Phatalate free (6P Free) Azo dye free
You can drop this product off at your nearest Recycling Center.
INTELLECTUAL PROPERTY
All intellectual property rights in relation to the product, including but not
limited to author’s rights and model rights, lie with the manufacturer, Pigro
Felice®. This product shall not be fully or partially copied, made public, or
imitated without the prior expressed or written consent from the legal owner.
The name and the Pigro Felice® logo are registered Pigro Felice® trademarks.
©2015 Pigro Felice® Ltd.
All rights reserved
Patent Pending
Made in China
Pigro Felice® Ltd.
Citicorp Centre – Units 1607/08
18 Whitfield Road
Hong Kong
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>