BH BIKES 2025_RS1 Road Bicycle User Manual

TekDoc
USER MANUAL
2025
RS1

2025_RS1 Road Bicycle

INTRODUCTION

This user manual contains important information for proper use and maintenance of the bicycle. In particular, this document contains specific information about the RS1 (LA555 / LA505 / LA455 / LA405). Please read the entire manual carefully. The user manuals of all BH models can be consulted on the website at the following address: https://www.bhbikes.com/manuals
Keep in mind that the manuals on the BH BIKES website are updated on a regular basis. Make sure you have downloaded the latest version from the website. You can check the version on the front page.
This document contains additional information to the general user manual, available at: https://www.bhbikes.com/es_INT/quienes-somos/manuales- descargas
You can check the characteristics, recommendations and warranties of third- party parts on their corresponding official websites.

SYMBOLS

| DANGER: refers to a hazardous situation that, if not avoided, will lead to serious injuries or even a fatal accident.
---|---
| WARNING: refers to a hazardous situation that, if not avoided, could lead to serious injuries or even a fatal accident.
| ATTENTION: refers to a hazardous situation that, if not avoided, could cause minor or moderate injuries.
| RISK OF ELECTRIC SHOCK: refers to a hazardous situation that, if not avoided, could cause serious injuries due to electric shock or even death.
| RISK OF SHORT CIRCUIT: refers to a hazardous situation that, if not avoided, could cause short circuits in the electrical components. Short circuits may cause damage to the electrical components and fire.

TOOLS

tightening torque will be indicated in newton metre.

TYPE OF ASSEMBLY COMPOUND

carbon elements.
**| ADHESIVE:** use medium strength thread lock.

****Adhesive is used to fasten bolts and make sure that they do not come loose due to vibrations when using the bicycle. Add a drop of thread lock to the tip of the screw thread in all cases. Never apply more than one drop around the thread, since this will make it very hard to remove the bolt.

BH WARRANTY

BH BIKES undertakes to offer long-lasting bicycles, in compliance with the highest standards of quality. Therefore, in addition to the statutory warranty, BH BIKES offers an additional coverage and warranty. This section defines the different types of warranty and the process that must be followed to register for the additional “LifeTime  Frame” warranty.

STATUTORY WARRANTY
The statutory warranty covers the original purchaser in the event of manufacturing defects and/or non-conformities. This warranty applies to frames and components manufactured by BH BIKES. The warranty period will be established according to the current laws of the country where the bicycle was purchased, and will start on the date of purchase. During this period, the holder of the warranty will be entitled to have all manufacturing defects repaired or replaced free of charge, including the reimbursement of transport expenses and any losses caused as a result of this. Different conditions must be met in order to be covered by the warranty:

• This warranty does not affect the consumer’s applicable rights, according to the current laws in each country.
• Faulty bicycles or parts will be covered by warranty upon the decision of our Technical Service.
• The warranty does not include the replacement of parts prone to wear and arising from normal use of the bicycle.
• The warranty does not cover defects or broken parts due to improper use of the bicycle, use for competitions, mounting of non-original accessories or improper handling and incorrect maintenance work.
• The warranty does not apply if the inspection before delivery and the corresponding inspection intervals included in this document have not been carried out, observed, documented as required and stamped by an authorised BH dealer.
• Should the repair not be satisfactory and not ensure that the optimum conditions are met according to the intended use, the holder of the warranty will be entitled to request the replacement of the purchased item or faulty part with one of identical characteristics, or to receive a refund of the amount paid for the damaged item or part.
• The warranty period will be interrupted during the repairs or, in the event of replaced items or components, it will be renewed.
• Any claim against this warranty shall expire six months after the end of the warranty validity period.
• All warranty claims must be processed by an authorised dealer.
• Geographical scope: refer to the User Manual or www.BHbikes.com

Visit the following link to read the terms and conditions: https://www.bhbikes.com/es_INT/registro-garantia-vida-bh/registra-tu-bici- garantia-de-por-vida

LIFETIME FRAME WARRANTY
Through its authorised stores, BH Bikes provides the original buyer with a commercial policy to cover any manufacturing defects in frames for a period beyond that specified in the product’s statutory warranty, pursuant to the following clauses:

1. The LIFETIME warranty solely applies to BH frames and bikes that are sold through stores that are authorised by BHBIKES EUROPE S.L.
   • The buyer must register the LIFETIME warranty online, with the information duly completed, within 30 calendar days of the purchase date, as it appears on the invoice issued by the authorised store.
   • This warranty cannot be transferred to subsequent buyers and it is cancelled when the bicycle is sold to a third party. Original buyer means the individual who registers the warranty at the time of the purchase; the commercial warranty cannot be transferred to third parties who are not the original buyer.
   • It shall be compulsory to have the bicycle serviced in an establishment that is authorised by BHBIKES EUROPE and according to the instructions in the user manual.

2. The LIFETIME warranty does not cover:
   • The rear swingarms of the double suspension models, fork, kids’ bikes, defects and/or fading of the original paint, or rust caused by natural deterioration.
   • Defects or breakages resulting from an accident or improper and/or negligent use of the bicycle.
   • When components or accessories that are not intended for or are not compatible with the use for which the bicycle was designed have been installed.
   • Defects resulting from improper handling.
   • Scratches, discolouration, or stains caused by the use of abrasive fluids, sharp items, clamps and/or prolonged exposure to sunlight or other weather conditions.
   • Defects caused by the bicycle’s normal wear and tear, including those due to material fatigue. Fatigue damage is a sign that the frame has been damaged by normal use, so it is the user’s responsibility to regularly inspect the bicycle.
   • Improper use and/or maintenance of the product (carefully read the recommendations for use and cleaning).
   • Frames that have been used in competitions, demos or as rentals.
   Read the full terms and conditions at: https://www.bhbikes.com/es_INT /registro-garantia-vida-bh/registra-tu-bici-garantia-de-por-vida

REGISTERING THE LIFETIME FRAME WARRANTY
You must register the bicycle within 30 days of purchase to enjoy the BH BIKES extended warranty. Follow the steps below to activate the LIFETIME FRAME extended warranty:

• LIFETIME FRAME WARRANTY

You must register the bicycle on the BH BIKES website to enjoy the LIFETIME FRAME extended warranty: https://www.bhbikes.com/es_INT/registro-garantia- vida-bh/registra-tu-bici-garantia-de-por-vida
Watch this video to find out what you need to do: https://youtu.be/47aLVgUI248
The serial number required to register the bicycle is located on the bottom of the bicycle, on the seat tube, above the bottom bracket:

SUBMITTING A WARRANTY CLAIM
All warranty claims must be channelled through an official BH dealer. The dealer will analyse the claim to identify its scope and perform a preliminary assessment of the incident. The dealer will submit and process the claim directly with BH. Once BH has defined the corrective measures required, the dealer will send this information to the customer.
All claims must be processed by the official dealer from which you purchased your bicycle. If this is not possible, please contact us directly. We will help you find an authorised dealer near you: https://www.bhbikes.com/es_INT /quienes-somos/contacto

MAINTENANCE

This user manual contains important information for RS1 (LA555 / LA505 / LA455 / LA405). Please read the entire manual carefully. The user manuals of all BH models can be  consulted on the website at the following address: https://www.bhbikes.com/manuals
This document contains additional information to the general user manual, available at: https://www.bhbikes.com/manuals
You can check the characteristics and recommendations of third-party parts on their corresponding official websites.

INSPECT THE BICYCLE BEFORE USE
Bicycles are inspected several times throughout the manufacturing process and then at the BH workshop during the final check. As the bicycle’s operation may be affected during transport or third parties may have modified the bicycle before its sale, the following must be checked before each trip:

• FRAME: no cracks, damage or strange noises.
• CHAIN: it must be lubricated and the transmission system must not make any strange noises.
• BRAKES: the brakes must be working properly. When stopped, press the brake lever with enough strength and check that it does not touch the handlebars.
• TYRES: the pressure must be correct and there must be no cuts on the tread or on the sides. Also check that the wear level does not exceed the maximum recommended level.
• WHEELS: the wheels must rotate freely in order to check how they rotate. Also check the space between the brake lining and the rim, as well as the space between the frame and tyre.
• STEERING: the steering must turn smoothly and with no strange noises.
• SWINGARM ROTATION POINTS: when weight is exerted on the bicycle, the suspension must work as expected and with no strange noises. If it is not working properly or there is play between the moving parts, this might mean that the tightening torques are incorrect or that the bearings are worn.
• BEARINGS: the bearings must work properly and with no strange noises. The bearings are subject to wear and must be replaced to prevent damage to the components on which they are installed.
• ELECTRICAL SYSTEM: if the bicycle features an electrical system, check that it is functioning properly by ensuring that the electrical assistance mode is running and that all parts are functioning properly (motor, display, change  of assistance mode and speed sensor). If there is no electrical assistance, check that all connections are correct and show no signs of damage.

| Do not ride your bicycle if it does not meet any of these points! A faulty bicycle may cause serious accidents!
If you are unsure or have any queries, please contact your nearest BH workshop!
---|---
| Check the tightening torques to make sure that they are as described in the recommendations in the user
manuals. Failure to observe these recommendations may result in accidents and even death.
| The effect of the ground and the forces exerted on the wheel subject the bicycle to a lot of stress. The different parts will be subject to fatigue and wear because of these dynamic loads. Check the bicycle at regular intervals to look for signs of wear, scratches, bent parts, wear on the finish or the formation of cracks.
Parts may fail suddenly after their service life has expired. Take your bicycle to an authorised BH workshop regularly to have these parts replaced if needed.

KEEP THE BICYCLE CLEAN
We recommend you follow these basic prevention measures to make sure that the bicycle is in perfect working order. Failure to observe these recommendations may lead to  premature wear or even breakages in specific areas, such as gaskets or moving parts.

• Clean the dust and mud with a damp sponge and a gentle and neutral cleaning product.
• Plastic parts must only be washed with soapy water.
• Tyres can be washed with a sponge or brush and soapy water.
• After cleaning the bicycle, dry it by rubbing it firmly with a smooth cloth.
• After each cleaning, lubricate the transmission elements.

Dirt may cause damage that can result in accidents or even death.
Never use pressure washers or steam cleaners.

KEEP THE TRANSMISSION LUBRICATED AT ALL TIMES
After washing the bicycle, the chain transmission’s lubrication may have also been washed off. Inspect and lubricate the chain’s links, if needed. Excess lubrication may attract more dirt, causing premature wear and incorrect functioning of the system.
Never use pressure washers or steam cleaners.

PART MAINTENANCE
The bicycle requires regular maintenance and a minimum number of regular inspections. The frequency of the maintenance operations depends on the type of vehicle (leisure, road or mountain bike), as well as the frequency and conditions of use.

Part| Action required| Before each outing| Monthly| Annually
---|---|---|---|---
Lighting| Functional check| | |
Tyres| Pressure check.| | |
Inspect the height of the profile and sides.| |
Brakes (on the rim)| Check the lever travel, lining strength and rim position.| | |
Brake test when stopped.| | |
Clean the brake pads.| | |
Brake cables| Visual inspection.| | |
Brakes (disc brakes)| Change the brake fluid (DOT fluid).| | |
Suspension fork| Check the bolts and the corresponding tightening torque.| | |
Change the oil and lubricate the elastomer.| | |
Saddle seat post with
suspension| Maintenance.| | |
Play check.| | |
Rims on rim brakes| Inspection and replacement, if needed, of the wall linings.| At the latest after the second part of the brake lining.
Bottom bracket axle| Check the play.| | |
Re-lubrication.| | |
Chain| Check and lubrication.| | |
Check and replacement.| After 800 km.
Chainsets| Check and tightening.| |
Wheels I Spokes| Check wheel spin and spoke tension.| | |
Headset| Inspection of the headset.| | |
Re-lubrication.| | |
Metal surfaces| Maintenance.| At least once every six months.
Hubs| Bearing inspection.| | |
Re-lubrication.| | |
Pedals| Bearing inspection.| | |
Lubrication, cleaning the anchoring mechanism.| | |
Saddle seat post / Stem| Inspection of the fastening screws.| | |
Rear derailleur /
Derailleur| Cleaning, lubrication.| | |
Quick-release
mechanism / Thru-axle| Efficacy check.| | |
Nuts and bolts| Check and tightening.| | |
Spokes| Tension check.| | |
Stem / Saddle seat post Circuit / Brakes| Removing and applying
new assembly paste.| | |
Components of the electrical assistance system| Disassembly and greasing.| | |
Check the connections.| | |
Check there is no dirt.| | |

You do not need to take the bicycle to an expert if you are skilled, experienced and have the appropriate tools. Immediately implement the corrective measures if you detect problems. If you are unsure or have queries, please contact BH.
The tasks described above must only be carried out by a trusted bike repair expert.

SPARE PARTS
Original parts must be used to ensure the optimum performance of your bicycle and the utmost safety. Failure to use original parts may cause damage that is not covered by the warranty.
The most common spare parts are parts prone to wear. The most common ones are tyres, inner tubes, brake pads, disc brakes and brake pads, as well as rims, when these are part of the brake unit, headlights, position lights, batteries and accumulators.

• TYRES: Replace them with an equivalent type of tyre. Check the marking on the outside of the tyre (ETRTO standard). Keep in mind that using a tyre with a larger outer diameter than the recommended one may cause the tip of the foot to touch the front wheel or rear wheel guard when the handlebars turn. The cyclist may lose control of the bicycle and suffer an accident with serious consequences. This can also occur when the pedal chainset is replaced with a longer one.
• INNER TUBES: Replace them with a suitable type of inner tube, according to the type of tyre. Refer to the information on the outside of the inner tube (ETRTO standard).
• DISC BRAKES AND BRAKE PADS: Follow the instructions supplied by the manufacturer.
• HEADLIGHTS AND POSITION LIGHTS: Replace the bulb with one of the same type. Check the indication on the metal area.
• CHAIN, COG AND CHAIN RINGS: Follow the instructions supplied by the manufacturer.
• BATTERIES AND ACCUMULATORS: Change for the same type. Check the indication on the outer area.

Remember that the failure to use original parts may cause damage that is not covered by the warranty.

AFTER A FALL, BLOW OR IMPACT
If you suffer a fall, blow or impact, first make sure that you are okay to continue cycling. Do not use the bike if you are injured and ask for medical assistance if needed.
If you are okay to continue cycling, check the bicycle to make sure that it is in perfect working order:

• Check that the wheels are firmly secured and that the rims are in the centre of the frame and fork. Turn the wheels. If they cannot be centred in situ because the gap is too small, separate the brakes from the rim so it can move freely.

In this case, keep in mind that the braking efficacy will be less.

• Check whether the handlebars or the front of the frame are twisted or broken. Check that the front is firmly seated on the fork, holding the front wheel firmly between your legs and trying to twist the handlebars with respect to the front wheel.
• Check that the chain is fitted correctly. If the bicycle fell onto the transmission side, check that it is working properly. Ask for help to place the bicycle on its saddle and change gears. When the chain fits on the largest cog, check the distance between the gear and the spokes. If the gear or bracket are bent, the first one may become stuck on the spokes – Danger of falling! The gear, rear wheel or frame may be damaged. Check the derailleur. If  it has shifted, the chain may come off the gear. The bicycle’s transmission will become  less effective (also refer to the “Traction” section).
• Check the saddle, upper tube or the bottom bracket box to make sure that there are no defects.
• Lift the bicycle slightly and let it drop onto the ground. If there are any noises, inspect the bicycle for any loose bolts.
• Inspect the entire bicycle again to check for bent areas, worn finish or cracks.
• Ride again carefully if no problems have been detected during the inspection. Do not brake or accelerate suddenly or pedal when going uphill. If you are unsure, wait for a car to pick you up instead of risking an accident. Once home, you should inspect the bicycle carefully again. If you are still unsure or have any queries, please contact your nearest BH workshop!

Bent aluminium parts must not be straightened, i.e., they must not be repaired. Even afterwards, there is a high risk of breakage, especially in regards to the fork, handlebars,  front part, chainsets and pedals. Replace them for greater safety.

WARNINGS ON USE

MAXIMUM TYRE SIZE
If you install a tyre of a different size on your bicycle, check and make sure that there are at least 6 mm between the tyre and other parts of the frame and fork.

MINIMUM AND MAXIMUM INSERTION LENGTH OF THE SEAT POST
Failure to observe the maximum and minimum seat post insertion dimensions indicated in this manual may cause a lever effect on the frame. The pressure exerted could damage the frame and cause serious accidents. The warranty does not cover the damage generated by failing to observe these indications.

MAXIMUM FORK LENGTH (AXLE-TO-CROWN)
Observe the maximum length between the fork axle and the lower part of the steering tube (axle-to-crown). If this maximum length is not observed, the frame could be damaged due to withstanding a greater load than that for which it was designed and may cause serious accidents.

MAXIMUM NUMBER OF STEERING SPACERS
This manual specifies the maximum number of steering spacers that can be fitted under the stem. If this maximum quantity is not observed, the materials could be damaged due to withstanding a greater load than that for which they were designed and may cause serious accidents.

POSITION OF THE SPINDLE INSIDE THE FORK TUBE
No steering spacers must be fitted above the stem. Otherwise, the materials could be damaged due to withstanding a greater load than that for which they were designed and may cause serious accidents.

INTENDED USE
Each bicycle has been designed to achieve a specific intended use. The models described in this manual have the following intended use:
This is a set of conditions for the operation of the bicycle that provides for its use on asphalt roads. In addition, the wheels must be kept in contact with the running surface at all times.

SIZES AND DIMENSIONS

ALL MODELS
RS1

| h1| h2| L1| L2| a1| a2| Stack| Reach
---|---|---|---|---|---|---|---|---
XS| 460| 120| 516| 412| 71º| 74.5º| 526| 370
SM| 480| 135| 531| 412| 72º| 74º| 544| 375
MD| 500| 150| 545| 415| 72.5º| 73.5º| 557| 380
LA| 520| 175| 561| 415| 73º| 73.5º| 583| 388
XL| 540| 190| 576| 418| 73º| 73º| 597| 393
XXL| 560| 215| 591| 418| 73.5º| 72.75º| 623| 398

TECHNICAL SPECIFICATIONS

mechanical)
Front brake| All| 160 mm
Minimum/maximum rear disc
diameter| All| 140 mm min / 160 mm max
Cabling| All| Internal ACR system
Bottle holder| All| 2
Compatible with mudguard| All| No
Compatible with pannier rack| All| No
Compatible with child seat| All| No
Compatible with trailer| All| No
Potentiometer compatibility| All| Yes
UCI Legal Certified| All| Yes
Maximum recommended weight (cyclist+equipment+bags)| All| 120 kg (marked on the wheels)

ASSEMBLY AND SPARE PARTS

DIMENSIONS OF THE STEERING TUBE
ALL MODELS

STEERING SPECIFICATIONS

Type| Contact angle with the compression ring / fork track| Bearing dimensions
---|---|---
Upper| 1.5″ Steerer| 45º| 52x40x7
Lower| 1.5″ Steerer| 45º| 52x40x7

HEADSET ASSEMBLY
ALL MODELS

00 HEADSET ref.: 383240700

Carbon forks must never be mounted with a spindle.
The  spindle may force the fork with a pressure for which it has not been designed. It may break and cause an accident.
Always mount the fork with an expander.

01 ACR STEERING COVER ref.: 383240800

02 ACR SPACER ref.: 383240900

03 ACR SPACER ref.: 383241000

EVO MONOCOQUE ACR STEM
LA555

04 BH AERO ACR STEM ref.: 391845000

SMR STEM
LA455 / LA405 / LA355

05 STEM ref.: 363300600

HANGER
ALL MODELS

06 HANGER

LA505
LA405|
---|---|---|---

MOUNTING THE BUILT-IN LOCK ON THE SADDLE’S SEAT POST
ALL MODELS

07 BUILT-IN CLAMP ref.:

DERAILLEUR BRACKET
ALL MODELS

08 DERAILLEUR BRACKET ref.:

BOTTLE HOLDER
ALL MODELS

09 BOTTLE HOLDER BOLTS

Di2 BATTERY
LA555 / LA505 / LA405

09 DI2 BRACKET ref.: 387211100

CABLING OF THE MECHANICAL PARTS
ALL MODELS

DECLARATION OF CONFORMITY

Declaration of Conformity
The manufacturer:
BH BIKES EUROPE, SL c/ Perretagana 10, 01015 Vitoria, Spain
Hereby declares that the following products:
Product description: Bicycles
Models designation:

MOUNTAIN BICYCLES:
LYNX TRAIL 9.9, LYNX TRAIL 9.5, LYNX TRAIL 9.0, LYNX RACE 9.9, LYNX RACE 9.5, LYNX RACE 9.2, LYNX RACE 9.0, LYNX RACE 8.5, LYNX RACE 8.0, LYNX RACE 7.5, LYNX RACE 7.0, LYNX RACE 6.5, LYNX RACE 6.0, LYNX RACE 4.0, LYNX RACE 3.0, ULTIMATE SLS 9.9, ULTIMATE SLS 9.5, ULTIMATE SLS 9.2, ULTIMATE SLS 9.0, ULTIMATE SLS 8.5, ULTIMATE SLS 8.0, ULTIMATE 9.5, ULTIMATE 9.0, ULTIMATE 8.5, ULTIMATE 7.7, ULTIMATE 7.5, ULTIMATE 7.0, ULTIMATE 6.5, ULTIMATE 6.0, EXPERT 5.5, EXPERT 5.0, EXPERT 4.5, EXPERT 4.0, SPIKE 3.0, SPIKE 2.5, SPIKE 2.0, SPIKE 1.0.

RACING BICYCLES:
ULTRALIGHT 9.0, ULTRALIGHT 8.0, ULTRALIGHT 7.0, ULTRALIGHT 6.0, AEROLIGHT 9.0, AEROLIGHT 8.0, AEROLIGHT 7.0, AEROLIGHT 6.0, RS1 5.5, RS1 5.0, RS1 4.5, RS1 4.0, RS1 3.5, SL1 4.0, SL1 3.5, SL1 3.0, QUARTZ 1.5, QUARTZ 1.0, AEROTT 8.0, AEROTT 7.0, AEROTT 6.0, GRAVELX CARBON 6.5R, GRAVELX CARBON 6.0AT, GRAVELX CARBON 5.5R, GRAVELX CARBON 5.0AT, GRAVELX CARBON 4.5R, GRAVELX CARBON 4.0AT, GRAVELX CARBON 3.5R, GRAVELX CARBON 3.0AT, GRAVELX 2.5, GRAVELX 2.0, GRAVELX 1.0, RX TEAM 5.0, RX TEAM 4.0, RX TEAM 3.0

CITY AND TREKKING BICYCLES:
OSFORD, OSFORD JET, OSFORD JET LITE, OXFORD JET PRO, OXFORD LITE, OXFORD PRO, SILVERTIP, SILVERTIP JET, SILVERTIP JET LITE, SILVERTIP JET PRO, SILVERTIP LITE, SILVERTIP PRO.

YOUNG CHILDREN AND YOUNG ADULTS BICYCLES:
EXPERT 26” DISC, ESPERT JUNIOR 14”, EXPERTE JUNIOR 16”, EXPERT JUNIOR 18”, EXPERT JUNIOR 20”, EXPERT JUNIOR 20” PRO, EXPERT JUNIOR 20” SUS, EXPERT JUNIOR 24”, EXPERT JUNIOR 24” DISC, EXPERT JUNIOR 24” PRO, EXPERT JUNIOR 26”, EXPERT JUNIOR 26” PRO.

Year of manufacture: 2024 and 2025
Comply with all of the relevant requirements of RD 339/2014, de 9 de Mayo.
The production control is assured by our Quality Management System, which fulfills the requirements of the standard ISO 9001
The following harmonized standards have been applied:
ISO 4210-1/2/3/4/5/8/7/8/9 – Safety requirements for bicycles
ISO 8098 Safety requirements for bicycles for young children
EN 16054 BMX bicycles. Safety requirements and test methods

Technical documentation filed at:
BH BIKES EUROPE, SL
C/ Perretagana 10,
01015 Vitoria, Spain
Prepared and reviewed by the BH Quality Department (Headquarters)

HELP AND ADDITIONAL RESOURCES

BH offers different channels to resolve your queries. In addition, you can join our global cyclist community on our social media.

TECHNICAL RESOURCES
You can find all of the resources you need to fine-tune your bicycle on the BH Bikes website. Click on the link below to access the user manuals, apps, warranties, display update files and videos that explain different operations: https://www.bhbikes.com/manuals
You can also check out our step-by-step tutorials to learn how to maintain and fine-tune your bicycle on our specialised Youtube channel:
https://www.youtube.com/user/ServicioTecnicoBH

CONTACT US
Our authorised dealers have the necessary knowledge and resources to help you with anything you need in relation to your bicycle. Don’t hesitate to contact your nearest store. You can find it by clicking on the link below: https://www.bhbikes.com/es_INT/tiendas/buscador-de-tiendas

To contact us directly:
Tel.: + 34 945 13 52 02
info@bhbikes.com 
P.I. Jundiz- Perretagana 10, 01015 Vitoria, Alava (Spain)
SOCIAL MEDIA
Join our global cyclist community. Discover the BH experiences of other cyclists and share yours.

www.bhbikes.com

References

• BH bikes | Tienda Online Bicicletas BH
• Contacto | Tienda Online Oficial de BH Bikes
• Manuales & Descargas | Tienda Online Oficial de BH Bikes
• Manuals & Downloads | Official Online store of BH bikes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>