Microtech DESIGNS e-LOOP Micro Wireless Vehicle Detection System Instructions

: July 29, 2024
: microtech DESIGNS

Table of Contents

Microtech DESIGNS e-LOOP Micro Wireless Vehicle Detection
Product Usage Instructions
Speciﬁcations
e-LOOP Micro Fitting Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Microtech DESIGNS e-LOOP Micro Wireless Vehicle Detection

Specifications

Frequency: 433.39 MHz
Security: 128-bit AES encryption
Range: up to 25 metres
Battery life: up to 2 years
Battery type: CR123A 3V 1500 m/a Lithium Battery x1 (included)
Replacement battery type: CR123A 3V 1500 m/a x 1

Product Usage Instructions

Step 1 – Wiring the e-TRANS 20

Option 1. Short-range coding with magnet

Connect the e-Trans 20 wires to the matching terminals on a gate motor.
Power up the e-Trans 20, then press and release the CODE button.
Place the magnet on the CODE recess on the e-Loop.
The systems are now paired, and you can remove the magnet.

Option 2. Long-range coding with magnet (up to 25 metres)

Power up the e-Trans 20, then place the magnet on the code recess of the e-Loop.
The systems will pair, and you can remove the magnet.

Step 2 – Fitting the e-LOOP Micro to Driveway
Using a 5mm concrete masonry drill, drill two mounting holes 40mm deep, then use the provided screws to fix to the driveway.

IMPORTANT: Never fit near high voltage cables as this can affect the e-Loop’s vehicle detection and radio range capabilities.

FAQ

Q: How do I know when to replace the battery?
- A: The battery life is up to 2 years, but if you notice a decrease in performance or range, it’s recommended to replace the battery with a CR123A 3V 1500 m/a x 1.
Q: Can I extend the range beyond 25 meters?
- A: The device is designed for a range of up to 25 meters. Attempting to extend the range may affect performance and reliability.

Speciﬁcations

Frequency: 433.39 MHz
Battery type: CR123A 3V 1500 m/a Lithium Battery x1 (included)
Battery life : up to 2 years
Range : up to 25 metres
Security : 128-bit AES encryption
Replacement battery type: CR123A 3V 1500 m/a x 1

e-LOOP Micro Fitting Instructions

Installation in 3 simple steps

Step 1 — Wiring the e-TRANS 20

Option 1. Short-range coding with magnet
Connect the e-Trans 20 wires to the matching terminals on a given gate motor. Power up the e-Trans 20, then press and release the CODE button. The LED on the e-Trans 20 will light up, now place the magnet on the CODE recess on the e-Loop, the yellow LED on the e-loop will ﬂash, and the LED on the e-Trans 20 will ﬂash 4 times. The systems are now paired, and you can remove the magnet.

Option 2. Long range coding with magnet (up to 25 metres) Power up the e-Trans 20, then place the magnet on the code recess of the e-Loop, the yellow code LED will ﬂash once now remove magnet and the LED will come on solid, now walk over to the e-Trans 20v and press and release the CODE button, the yellow LED will ﬂash and the LED on the e-Trans 20 will ﬂash 3 times, after 15 seconds the e-loop code LED will turn oﬀ.

Step 2 — Fitting the e-LOOP Micro to Driveway
Using a 5mm concrete masonry drill, drill the two mounting holes 40mm deep, then use the 5mm concrete screws supplied to ﬁx to the driveway.

IMPORTANT : Never ﬁt near high voltage cables, this can eﬀect the e-Loop’s vehicle detection and radio range capabilities.