microtech DESIGNS EL00M e-Loop Mini Presence Mobile Instruction Manual

Table of Contents

Specifications

e-LOOP Mini Fitting Instructions

Installation in 3 simple steps

Option 1: Short-range coding with magnet

Power up the e-Trans 50, then press and release the CODE button.
Place the magnet on the CODE recess on the e-Loop; the yellow LED will flash, and the blue LED on the e-Trans 50 will flash 3 times.
The systems are now paired, and you can remove the magnet.

Option 2: Long-range coding with magnet (up to 50 metres)

Power up the e-Trans 50, then place the magnet on the code recess of the e-Loop; the yellow code LED will flash once.
Remove the magnet, and the LED will come on solid. Walk over to the e-Trans 50 and press and release the CODE button.
The yellow LED will flash, and the blue LED on the e-Trans 50 will flash 3 times. After 15 seconds, the e-loop code LED will turn off.

To the driveway

Face the arrow on the base plate towards the gate.
Using a 5mm concrete masonry drill, drill the two mounting holes 55mm deep.
Use the 5mm concrete screws supplied to fix to the driveway. (Refer to diagram on the right)
Fit the e-loop Mini to the base plate using the 4 hex screws supplied, ensuring the arrow also points towards the gate for alignment.
The e-Loop will become active after 3 minutes.

NOTE: Ensure hex screws are tight as this forms part of the water sealing process.

IMPORTANT: Never fit near high voltage cables; this can affect the e-Loop’s vehicle detection and radio range capabilities.

Frequently Asked Questions (FAQ)

Q: How long does the battery last?
A: The battery life is up to 3 years with AA 1.5V 3000 mAh Lithium Batteries included.
Q: What is the range of the system?
A: The system has a range of up to 30 metres for wireless vehicle detection.
Q: How do I pair the e-Loop with the e-Trans 50?
A: You can pair them using short-range coding with a magnet or long-range coding with a magnet as per the instructions provided.

Installation in 3 simple steps

Step 1 – Coding e-LOOP Mini version 3.0
Option 1. Short-range coding with magnet
Power up the e-Trans 50, then press and release the CODE button. The blue LED on the e-Trans 50 will light up, now place the magnet on the CODE recess on the e-Loop, the yellow LED will flash, and the blue LED on the e-Trans 50 will flash 3 times. The systems are now paired, and you can remove the magnet.
Option 2. Long range coding with magnet (up to 50 metres)
Power up the e-Trans 50, then place the magnet on the code recess of the e-Loop, the yellow code LED will flash once now remove magnet and the LED come on solid, now walk over to the e-Trans 50 and press and release the CODE button, the yellow LED will flash and the blue LED on the e-Trans 50 will flash 3 times, after 15 seconds the e-loop code LED will turn off.

Step 2 – Fitting the e-LOOP Mini base plate to the driveway

Face the arrow on the base plate towards the gate. Using a 5mm concrete masonry drill, drill the two mounting holes 55mm deep, then use the 5mm concrete screws supplied to fix to the driveway.

Step 3 – Fitting the e-LOOP Mini to base plate

(Refer to diagram on the right)

Now fit the e-loop Mini to the base plate using the 4 hex screws supplied, making sure the arrow also points towards the gate (this will ensure keyway is aligned). The e-Loop will become active after 3 minutes.
NOTE : Ensure hex screws are tight as this forms part of the water sealing process.
IMPORTANT : Never fit near high voltage cables, this can effect the e-Loop’s vehicle detection and radio range capabilities.

Microtech Designs
enquiries@microtechdesigns.com.au