Seren A6003 Close Coupled Corner Toilet with Soft Close Seat and Cover Instruction Manual

July 27, 2024
Seren

Sanitary fixing systems
Installation instruction

A6003 Close Coupled Corner Toilet with Soft Close Seat and Cover

A6003-
WC, BIDET&SEMI-PED FIXING SET
Usage
For fixing of:standing toilets and bidets.
contents

1 2xXFloor brackets
2 2xwallplugs S10 50
3 2XHex head screw 6X60
4 2 X Washers
5 2x St. Steel Screw 5×60
6 2X Nylon Bushes
7 2x Chrome Caps

Dual Flush Valve Instruction

Installation Layout

TIP

  1. Read all manipulation and installation guidetine, and p-ease install it step by step according to the installation guideline and prevent any damage from product breakage and improper use.
  2. All material are written according to the latest information when design. Our company reserve the right to change product characterizes, package and supply at any time without notice.
  3. Do not use corrosive detergent (such as hypochlorite} in water tank because such strong oxiaant makes fittings damaged easily and lead to leakage. The mentioned above situations are beyond the range of our guarantee
  4. Our company do not bear the related loses and damages caused by use other company’s parts and material such as glass glue.
  5. Suitable temperature range: 0~45°C

Functional Instruction

  1. The flush valve has 2 flushing ways haif—flush and full flush: when you push the full flush, the discharge volume is big and when you push the half flush, the discharge volume is small.
  2. Water level of half flush is adjustable. (Refer to photo 6)
  3. Water level of full flush is adjustable. (Refer to photo 3-2)

Installation Steps

I. Preparation before installation
Remave tre old fittings and wash tank oefore installation. And wash clean because many impunties probably exusted in condult.
II. Flush Valve Installation (According to the actual need}
1. Stainless steal hook for one-piece flush valve installation Contrarotate drainage body and make it remove from pedestal. Circumrotate stainless steel hook to the end of bolt clockwise.
Let pedestal aim at the water tank circum*otate, and, the stainless steel hook can reach the scupper downside, then, revise the pedestal, the sealing washer shouid put outside. Go through the pedestal the middle finger of left hand to keep off star steal hook and make tts both sides put around the outfall symmetrically. Circumrotate bolt by screwdriver and be sure that seal between sealing washer and the surrounding for outfall.
Let flush valve body insert into pedestal and circumrotate it inside the buckle clockwise.
2. Two-piece flush vaive installation Contrarotate drainage body and make it removed from pedestal.
Let pedestal insert into outfall from ins:de of water tank, cover the drainage plastic washer, circumrotate drainage nut and cover the standard washer, and it can adjust the put angle praperly according to the actual size of water tank.
Lat flush valve body insert into pedestal and crcumrotate it inside the buckle clockwise.
Notice: If the product is different from the photo shown, please refer to the actual product.
III. Fill Valve installation Put fil valve & woter— inlet trangle washer insert into water—inlet hole of water tank then, cover water-inlet hexagoral nut in turn from the bottom of fill velve. Fastening water inlet haxagonal nut and make a proper adjust accordig to the water tank.
Adjust water levet
Fetch out bucket and screw off water-iniet body anti-clockwise: pul upside  or prass downsidee to the proper situation, then,screwing on water-iniet body closely and install the buckte. Little  adjustment on water level revolve adjusted rod to adjusted the height of water —stop and bupy to reach the surtabie Water level you need.
Connect weter-supply pipe and dust in adapter of filter according to your actual need.
Notice:

  1. Be sure that buoy is active freely before fil valve installation.
  2. Wash tha mpurey in the conduit when you connectng water-supply pipe.
  3. The heght of eter level can net beyond overflow mouth of flush valve when aduusting water level.

V . Water tank Installation
Put water tank on ceramic toilet and make standard washer located at the outfall of toilet. Just the photo shows, tet jointed bolt insert into installation hole , then, screw the jointed nut closely.
VI. Examination
As photo show, connect water—niet pipe to test and notice the following Phenomenon:

  1. According to the height of haif flush to adjust half flush water tevel:
    when half flush buoy is higher, the drainage volume is less; when it is lower, the drainage volume is more.

  2. Adjust the height of water level by the adjusted digit and its corresponding adjusted patch. The placket is big and its water level is hugh: the placket is small and its water level is low (Note: When adjusting full flush water level, please fetch out flush valve, then, install fiush valve again correctly after adjusted.)

  3. Adjust all parts position to prevent them from interference.

  4. Open & close for water-stop cup rs normal and has no ieakage.

  5. It is normal for full flush and half flush.

Vll. Push button Installation

Screw off push button nut. Let push button instart tank lid mci hole, Screwing on push button aut from the botton of water tank lid, then, screwing the adjusted nut closely and be sure that it is faim. Please confirm pull flush rod press the flush valve key-press whether or not and check it is blocked or not.
Note: Screw off pull flush rod, the cut part is upside. Note: Pull flush rod should aim at the full flush key-press.

Vll. Examination Again
Cover water tank lid and notice the following phenomenon to confirm installation complete or not:

  1. Open & close for water – stop washer is normal and has no leakage.
  2. It is normal for full flush and half flush and they flush excetlentty.

Trouble Shooting

Symptoms Probable Corrective actions
Water level is too high or too low Do not adjust the water level offal vane
well Refer to photo 5 to adjust water level
Always water-inlet or do not water-irgel (for fill valve) 1. Switch of fill

valve is close
2.Buoy is extrusive by water tank wan.
3.Fitter has been blocked owing to bad water quality| 1.Open the fill valve switch.
2,Adjust fit valve direction.
3.Wash filter (refer to photo 3-1).
Leakage| 1.1111 valve nut is loose.
2.F lush valve does not installed well
3.Pull flush rod is too long to Ong out/all wet (refer to photo 7-4)
4.Flush valve body and pedestal does not match welt
5.Refill water pipe Insert into overflow mouth too deep.| 1 Screw the fill valve nut closely.
2.instan flush valre again according tette installation Star).
3. A Adjust the adjusted nut (refer to photo 74.3.
4).B Shorten the pull ush rodAis prior to B.
4 Install again (refer to the installation */ flush valve).
5 Refit wear pee depth can not beyond the height of water level.
No drainage or less drainage| Pull flush rod is too short to press drainage pipe| Adjust adjusted nut (tele; to 7-2).
Water level for half flush
Is too high or too low| Water level does not adjusted well| Adjust water level (refer to photo 6).

Soft Close Toilet Seat Installation Instructions

Insert the hinges into the toilet.
Tighten the screws in a clockwise directian(do not over tighten)
Untighten the screws a bit by turning them 90° in a anti-clockwise direction this will allow you to align the seat.
Clip on the toilet seat. Align the toilet seat with ceramic bowl.
Take off the toilet seat by pressing both push buttons.
Tighten the screws in a clockwise direction.
Place the cover over the hinges.
Clip on the toilet seat and cover.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals