Inrico B06 Handheld Network Walkie Talkie User Guide

Inrico B06 Handheld Network Walkie Talkie

Notes Before Using

• Please read the following content carefully. Radio users need to gain general knowledge and risks.
• Do not use the device or charge the battery in any hazardous areas such as gas, dust, steam, etc.
• Please turn off the device while refueling or parking at the gas station.
• Do not disassemble your radio.
• Avoid prolonged time in the sun or placing it near a heating appliance.
• Avoid excessive exposure to extremely dusty, damp, and splashing places, or leave it on an unstable surface.
• Reparation by professional technicians, do not disassemble by yourself.

Disclaimer

• Inrico reserves the right to modify product design and specifications.
• Inrico assumes no responsibility in the event of printing errors.
• All specifications are subject to change without notice.

Unpacking and Device Checking

• Please unpack and take out the device and all accessories carefully, and ensure all lists have been gotten before discarding the cardboard box.
• If any items are lost or damaged in transit, please contact our distributors.

Accessories

Handling Precautions

• Do not overcharge the battery Please stop charging if it can’t be fully charged within the required time.
• The battery probably overheats, smokes, bursts, or is suddenly on fire due to an abnormal charging process. When fully charged or not charged, please disconnect the charger and unplug it from the power outlet.
• Do not discard the battery in a microwave or high-pressure container.
• The battery probably overheats, smokes, bursts, or suddenly on fire.
• Do not expose the damaged battery near any fire.
• If the battery is broken, leaking, or has an abnormal odor, please remove it from flammable areas immediately. The fluid in the battery is flammable, which may cause smoke and fire.
• Do not use an abnormal battery If the battery is odd smelly, discolored, deformed, etc., please stop charging or disassemble from the device immediately.
• Please use an authorized power adaptor To comply with warranty terms and avoid damages, charge the battery using a specified charger for best performance.
• Please do not charge at high or low temperatures.

Battery Care

Fully Charge the Battery Before Initial Use

• Do preserve battery life by switching off a device and removing the batteries when it’s not being used and are not expected to be used for extended periods.
• Do practice proper battery storage by keeping batteries in a cool, dry place at normal room temperature.

Properly Store Batteries

• Remove the battery from the device.
• Charge and discharge the battery to 40%-65% if it will not be used for 10 days or more. This can greatly extend the battery life.
• The battery should drop below 65% when it is idle for more than 10 days to prevent it from swelling.
• Store the battery in a cool and dry environment that’s less than 25°C.

Features of Lithium Battery

• Battery capacity will reduce after multiple charging cycles.
• The battery capacity drops gradually even without being used.
• Longer charging time is required in shady places.
• Charging and storing lithium batteries in warm conditions will shorten their lifespan. Please do not leave them inside the vehicle or near the heater.
• If the battery working time has reduced significantly, please replace the battery immediately to avoid fluid leakage.

Clean and Maintenance

• Before cleaning and maintaining the device: please stop running, turn off the device, and disconnect all connections with other equipment.
• When you do not use the radio, please cover the accessories connector.
• When cleaning the dust, please use a soft brush and neutral detergent (no strong corrosive chemicals) to wipe it.
• Please keep the equipment and accessories dry.
• Please do not use the microwave oven hair dryer or other heating devices to dry them.

Product Overview

Functions Sheet

when receiving

The red light is always on when transmitting during PoC

F1| Short press| Broadcast the group leader’s recording|
Long press| Press and hold for 15s to reset the

RSM and pair again

|
F2| Button Name| Talk: Switch to the previous group and make a voice broadcast

Music Play: Previous song

|
F3| Short press| Talk: Switch to the next group and make a voice broadcast

Music Play: Next song

|
Volume Button| Volume+| Volume up|
Volume –| Volume down|
SOS

Button

| Short press| SOS|
Long press| End SOS|
__

__

__

__

__

Power Button

| __

__

Short press

| Incoming Call: Answer Calling: Hang Up

Music play: Pause/Play

|
Double click| Incoming Call: Reject|
__

__

Long press

| Shutdown state: Power on

__

Power on status: Power off

|

Accessories Installation

Attaching the Battery

• Align the electrical contact of the battery with the bottom rails.
• Press the battery firmly, and make sure the electrical connection touches the bottom.

Attaching the Battery Cover

• Close the battery cover
• Press the two-layer battery cover
• Fasten the two screws

Install the belt clip

• push the belt clip along the “T” slot to the bottom.

Remove the belt clip

• Lift the buckle and pull the belt clip upward.

Status Indicators

Function Operation

1. Call Handling
   When there is an incoming call to the RSM, short press the on/off button to answer the call when the shoulder microphone is connected.

2. Reject Calls
   When the RSM has an incoming call, double-press the switch button to reject the call.

3. Hang up Calls
   Click the on/off button to hang up while on a call.

4. Music Pause/Play
   When the RSM-connected device plays music, short press the on/off button to play or pause.

5. Standby
   When the RSM is in the pending pairing state, after 15 minutes without connecting Bluetooth, the system will automatically shut down.

6. PTT Function
   RSM supports terminal equipment intercom software, terminal equipment, and RSM Bluetooth connection can achieve PTT function through the PTT button.

7. NFC Connection
   When the RSM is in a state of pending pairing, use the relevant NFC device to perform NFC sensing and Bluetooth connection.

8. Body QR Code
   Information can be read using related device scanning

Simple Troubleshooting

the battery.

•   The battery may be out of power. Charge or replace the battery.

•   The battery may be in poor contact due to dirt or damage. Clean the electrical contact or replace it.

Terminal Crash| •   Due to high-strength radio frequency interference, such as being close to high-power TV transmission towers, GSM base stations or airports
Buttons Not Working| •   The buttons may not work temporarily, restart the terminal.

•   The buttons are broken, contact the dealer or our company.

Echo or Noise During Connecting| __

•  The speaker may be covered, clean the speaker surface.

Shorter Standby Time| __

•   The battery life becomes shorter in high-temperature environments. Replace a new qualified battery.

•   Power consumption increased in areas with weak signals. Please temporarily turn off the device.

Can’t Connect to Bluetooth| __

•   •The device cannot work properly or cannot be used. Please confirm whether the device is turned on.

•   Confirm whether the device and terminal are paired successfully.

Disconnected from

Terminal Device

| •  Check whether the battery is too low and whether the distance between the microphone and the terminal device is within 10 meters, Or whether there are dry shielding obstacles in the middle, etc.

Specification

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment

For CE

A1703, Shenzhen National Engineering Laboratory Building, No. 20 Gaoxin South 7th Road, Shenzhen, China
Tran s mitter Frequen c y :| BT: 2402-2480MHz

BLE: 2402-2480MHz

Rece i ver Frequen c y :| BT: 2402-2480MHz

BLE: 2402-2480MHz

RF-Output Power :

ERP / E I RP / Conducted

| BT: 2.32dBm

BLE: 9.14dBm

Please read this instruction book carefully before using it and keep this with care. www.inricosolutions.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>