Anmi DD-a Phantom Light Strip Instruction Manual

Anmi DD-a Phantom Light Strip

Specifications

• Bluetooth version: XYZ
• Power: XYZ
• Indicator light colors: Blue, Red
• Battery type: Button battery

Product Usage Instructions

Bluetooth Connection Instructions:

1. Turn on the power of the device.
2. Click on the mode button to switch to Bluetooth mode. The indicator light will show blue.
3. Turn on the Bluetooth device you wish to connect to.
4. Enable the Bluetooth switch on the device.
5. Check for the device name “DD-a” in the available Bluetooth  devices list.
6. The indicator light will flash when the connection is successful.

Installation:
Follow the installation instructions provided in the user manual to set up the product properly.

product Function Introduction:
The product is designed to provide XYZ functions. Refer to the
user manual for detailed information on its features.

Information to User:
The label on the product indicates that it contains a button battery. Please handle and dispose of the battery properly according to local regulations.

FAQ:
Q: What should I do if the Bluetooth connection fails?
A: If the Bluetooth connection fails, try turning off both devices, turning them back on, and attempting the connection  process again. Ensure that both devices are within close proximity for a stable connection.

Phantom light strip

Product Display

Bluetooth connection instructions
Turn on the power, click “mode” to switch to Bluetooth mode, the indicator light will show “blue”.
Turn on the Bluetooth device to connect, turn on the Bluetooth switch, and check “DD-a”.
The indicator light flashes when the connection is successful.

Production information:

• Product Name: Phantom light strip
• Model Name : DD-a
• Series Model : DD-b, DD-c
• Input Voltage: 3.7V
• Manufacturer: Zhongshan Anmi Lighting1 Technology Co., Ltd
• Address:5t h Floor, No. 6 Juyuan South Road, Lianfeng
• Community, Xiaolan Town, Zhongshan City

Installation

1. Step1:Rip off the protective film.
2. Step2:Press the power button before use.
3. Step3:nsert the spike into connecting rod
4. Step4:Assemble the solar panel to cradle
5. Step5:Make sure the panel are fully exposed to the sun

Product function introduction

The solar panel MUST be installed in a well-lit ocation where it can receive maximum sun light during daytime hours.Any cover that shades the panel will affect its ability to absorb sunlight and decrease the amount of brightness and duration of the LED lights. The lights and solar panel box are all weather devices .They should not be affected by exposure in rain,snow or temperature Suitable for gardens, lawns, flower beds, passa ges, doorsteps, or any other place you want.

Information to user:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

The label indicates that the product contains a button battery

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>