BUILTBRIGHT BB8KA06 Harness Type A 6 Perimeter Lights Plus Mini Bar Instruction Manual

July 25, 2024
BUILTBRIGHT

BUILTBRIGHT BB8KA06 Harness Type A 6 Perimeter Lights Plus Mini Bar

Instruction Manual

PARTS LIST

  1. 1x Type A Main Harness (BB8K001)
  2. 1x Short Y Splitter Adapters (BB8S001)
  3. 1x Long Y Splitter Adapters (BB8S002)
  4. 1x Extension Harness for Perimeter Strobe (BB8SE01)
  5. 1x Type A Switch Harness
  6. 1x 5 Core Pigtail
  7. 6x Connector Caps
  8. 13x Connector Retainers

1x Inline Fuse Holder + 15 Amp Fuse

INSTALL NOTES

  • No cutting or drilling is required for the installation of the front grille strobes or roof top mini
  • Drilling is only required when mounting the lights on the rear tail gate, bumper or on the body of the
  • Approximate installation time is 2 hours (not including bracket installation).
  • Lights are not included in this Compatible lights are listed below.

COMPATIBLE LIGHTS

SKU PERIMETER STROBE COLOR
BB6110A 4″ Strobe Light, Amber (1EA)
BB6110B 4″ Strobe Light, Amber/White (1EA)  
BB6110C 4″ Strobe Light, Amber/Blue (1EA)  
BB6110D 4″ Strobe Light, Amber/Green (1EA)  
BB6010A 4″ Strobe Light, Amber (1EA)
BB6010B 4″ Strobe Light, Amber/White (1EA)  
BB6010C 4″ Strobe Light, Amber/Blue (1EA)  
BB6010D 4″ LED Strobe Light, Amber/Green (1EA)  
BB6001BK Mini Light Bar 12”, Amber/White (1EA)  
BB6001CK Mini Light Bar 12”, Amber/Blue (1EA)  
BB6001DK Mini Light Bar 12”, Amber/Green (1EA)  
BB6011AK Mini Light Bar 15”, Amber (1EA)
BB6011BK Mini Light Bar 15”, Amber/White (1EA)  
BB6011CK Mini Light Bar 15”, Amber/Blue (1EA)  
BB6011DK Mini Light Bar 15”, Amber/Green (1EA)  

STEP 1 – PLAN THE INSTALL

  1. Unbox your harness kit and verify that all parts are present. 2. Lay out the harness and plan where to install the perimeterstrobes (sold separately). Plan and lay out the necessaryadapters and extensions alongside the Main Harness (A).
  • Note: There are is a Short Y Splitter Adapter (B) and a Long Y Splitter Adapter (C) included in this Please choose theproper adapter according the location you want to install your lights. Examples:
  • The Short Y Splitter Adapter (B) is long enough if you install the front perimeter strobes in the grille. If you want to install the lights on the bumper or side of the vehicle, you may need to use the Long Y Splitter Adapter (C).
  • The Short Y Splitter Adapter (B) is long enough if you install the rear perimeter strobes under the tail If you want to install the lights on the side of the vehicle, you may need to use the Long Y Splitter Adapter (C).
  • The standard harness and splitter adapters are long enough for standard pick up truck beds or flat beds up to 10’ long. If you choose to install the rear perimeter strobes on a truck body and route the harness through the cabin, you may need to use the Extension Harness for Perimeter Strobe (D).
  • An example configuration is shown on the next page for

EXAMPLE cONFIgURATION

This example uses Harness Kit #BB8KA06, 6x Perimeter Strobe #BB6110B, 1x 12” Mini Light Bar #BB6001BK, 2x Grille Bracket Kit #BB96GFA and 1x 3rd Brake Light Mount Bracket Kit #BB96RFA.
Lights and brackets are sold separately.

STEP 2 – PROgRAM THE PERIMETER STROBE LIgHTS

We suggest programming the lights and testing harness functionality before beginning installation on the vehicle.

  1. Unbox all of the perimeter strobe lights. A waterproof 5 pin male connector and a female pigtail are included in the package of each light.
  2. Unplug the lights from the pigtails (Fig. 1) and plug the lights into the Y splitter adapters of the Main Harness (A).
  3. After all lights are plugged into their locations, unplug the grille and rear connectors from the Main Harness (A) (Fig. 2).

STEP 2 – PROgRAM THE PERIMETER STROBE LIgHTS

  1. Use two of the 5 core pigtails that come with the perimeter strobe lights to program each of the light bundles separately (Fig. 3). If preferred, connect the wires of the pigtails together to program all 6 lights at

  2. See Fig. 4 for individual wire functions. Refer to the perimeter strobe light instructions to program the RED and   GREY wires to desired strobe

  3. Unplug the programming pigtail and leave the light bundles unplugged from the Main Harness (A). They will be connected to the Main Harness (A) once it’s routed through the vehicle

STEP 3 – INSTALL THE HARNESS AND LIgHTS

  1. Prior to routing through the vehicle, cap the Main Harness (A) connectors with provided Connector Caps (G). Capping the connectors is highly recommended to prevent dirt or grease getting into the female connectors during

STEP 3 – INSTALL THE HARNESS AND LIgHTS

  1. Locate the vehicle’s main harness along the frame rail. Route the StrobeLinkTMMain Harness (A) alongside it, starting under the cab and working towards the
  2. Remove the Connector Cap (G) and connect the Y splitter adapter for the rear strobe
  3. Route the front portion of the harness under the cab and into the engine Secure to the vehicle’s wiring on the firewall or inner fender. Do not rest the wires against the exhaust.
  4. Remove the Connector Cap (G) and connect the Y splitter adapter for the front strobe
  5. Locate the Main Harness (A) wire labeled “Top” and route it through the vehicle towards the top of the cab. Connect the mini light bar.
  • An example configuration is shown on the next page for

EXAMPLE cONFIgURATION

STEP 4 – INSTALL THE LIGHT CONTROL

There are 3 options to control your strobe lights: 1. Use Provided Switch Panel

  1. Use Upfitter Switches
  2. Use 3rd Party Switches
  • Note: If the battery or fuse box of the vehicle is on the passenger side , you will need Power Extension Cable BBSE02 (sold separately) to extend between the power connector

on the Switch Harness (E) and the pigtail to reach the power source.

Each option is outlined individually on the next 2 pages.

STEP 4 – INSTALL THE LIGHT CONTROL

There are 3 options to control your strobe lights: 1. Use Provided Switch Panel

  1. Use Upfitter Switches
  2. Use 3rd Party Switches
  • Note: If the battery or fuse box of the vehicle is on the passenger side , you will need Power Extension Cable BBSE02 (sold separately) to extend between the power connector

on the Switch Harness (E) and the pigtail to reach the power source.

Each option is outlined individually on the next 2 pages.

STEP 4 OPTION 2 – USE UPFITTER SWITCHES

  1. Plug the provided 5 Core Pigtail (F) into the switch connector on the Main Harness (A). See Fig. 5 for individual wire
  2. Locate the upfitter switch relay in the engine bay. Connect the BLACK wire to ground.
  3. Connect the RED , GREY or WHITE wire to the desired upfitter switch When the upfitter switch is activated, that light and pattern will trigger.
  4. Secure any slack with zip ties. Unused wires should be separated and protected using heat shrink or

STEP 4 OPTION 3 – USE 3RD PARTY SWITCHES

  1. Plug the provided 5 Core Pigtail (F) into the switch connector on the Main Harness (A). See Fig. 5 for individual wire
  2. Follow the same wiring instructions from Option 2

STEP 5 – TEST + COMPLETE

  1. Test the StrobeLinkTMsetup for desired functionality. Once verified, secure any wire slack with zip
  2. Use the provided Connector Retainers (H) to secure If your vehicle is operated in a high-corrosion environment, apply dielectric grease in the connectors for additional corrosion protection.
  3. If there is an unused connector exposed, use a Connector Cap (G) to cap it Wrap tape around the cap to secure.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BUILTBRIGHT User Manuals

Related Manuals