TAC 4S-19C1132-1 Upgraded 4 Inch Oval Straight Sidebar Installation Guide
- July 25, 2024
- TAC
Table of Contents
TAC 4S-19C1132-1 Upgraded 4 Inch Oval Straight Sidebar
Product Information
Specifications
- Product Name: Upgraded 4in Oval Straight Sidebar
- Compatible Vehicles: 2019-2024 Silverado/Sierra 1500 Double Cab, 2020-2024 Silverado/Sierra 2500/3500 Crew Cab
- Mounting Type: Rocker Panel Mount (1500 Double Cab), Body Mount (2500/3500 Crew Cab)
- Part Number: 4S-19C1132-1
FAQ
Frequently Asked Questions
- Q: Can I use polish or wax on the product?
- A: To protect your investment, wax the product after installing. Regular waxing is recommended, but avoid using any polish or wax that may contain abrasives that could damage the finish. Aluminum polish can be used for small scratches and scuffs. Mild soap is also suitable for cleaning the sidebars.
- Q: What maintenance is required after installation?
- A: It is advised to periodically inspect the installation to ensure all hardware remains secure and tight. This helps maintain the longevity and performance of the sidebars.
PARTS LIST
| 1 | Driver/left Sidebar | 12 | 8-1.25mm x 30mm Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right Sidebar | 12 | 8-1.25mm x 25mm Combo Bolts |
| 6 | Mounting Brackets | 12 | 8mm Lock Washers |
| 12 | 8mm x 24mm x 2mm Flat Washers |
INSTALLATION INSTRUCTIONS
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the driver/left side of the vehicle. Locate the plastic plugs along the bottom edge of the body. Mounting Brackets will bolt to the 1st, 2nd and 4th threaded mounting holes, (Figure 1). Remove the plastic plugs from each mounting location, (Figure 2).
- Directly above each threaded insert is a top mounting location on the side of the body panel.
- Hold a Bracket up in place to help determine the correct mounting holes to use along the body.
- NOTE: Thread an 8mm Hex Bolt into the threaded inserts to clear paint as required.
- Select (1) Mounting Bracket, (Figure 3). Starting at the front of the driver/left side, attach the Mounting Bracket to the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 3 & 4). Do not fully tighten hardware.
- Repeat Steps 1 & 2 to attach the center and rear Brackets to the center and rear mounting locations along the body panel, (Figures 5 & 6).
- Select the Driver/left Sidebar. Use the illustration above to help determine the correct Sidebar.
- NOTE: The front stepping pad is farther away from the front end of the Sidebar. Place the Sidebar on top of the Brackets. IMPORTANT: Do not slide, (front to back), the Sidebar on the Brackets or damage to the finish may result.
- Attach the Sidebar to the Brackets with (6) 8mm Combo Bolts, (Figures 7 & 8).
- Level and adjust the Sidebar and fully tighten all hardware.
- Repeat Steps 1—6 to install the Passenger/right Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
Aluminum polish may be used to polish small scratches and scuffs on the
finish. Mild soap may be used also to clean the Sidebars.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>