ideal HEATING 221528 Halo Lite RF Instructions
- July 23, 2024
- ideal HEATING
Table of Contents
ideal HEATING 221528 Halo Lite RF
WELCOME
Welcome to your new Ideal Halo control. This thermostat will help you to
control both your heating temperature and the times that your heating is on.
Halo Lite RF is a battery powered, wireless control, that communicates on an
868MHz frequency to a wired receiver located near to your boiler or heat pump
control box.
This user guide is applicable to the Halo Lite RF control only.
Halo Lite RF is a non-connected control (control is via the Halo Lite unit
only).
USING YOUR HALO LITE RF
MAIN FEATURES
Mode Selection
You can choose to run your Halo Lite RF in Auto, Manual or Off mode.
Auto: Runs your heating to pre-set scheduled times and temperatures.
Manual: You control the temperature by physically turning the dial.
Off: Your heating will be set to a low temperature (default 5 0C) for
frost protection.
Move between Auto, Manual and Off modes using the right hand side button,
scroll down the menu using the dial and push to select.
TOP TIP
Your Halo Lite RF is designed to provide the perfect balance of comfort and efficiency. It has a feature called Enhanced Load Compensation which balances the temperature in your radiators to maintain the target room temperature with optimum efficiency. As a result you might notice that when the temperature in your home reaches the target your radiators are not hot to touch. By controlling the temperature in your radiators your system is working in the most efficient way for you.
Override
If you are running a schedule with pre-set times (Auto mode) and you want to
adjust the temperature of your heating temporarily, simply turn the dial to
your desired temperature.
The new temperature will be active until the next scheduled change shown under
the target temperature.
The home screen will now display the override icon above the current
temperature.
TOP TIP
You could use this feature if you want to boost your heating to a higher temperature for a period of time. May be you’re feeling chilly or it’s the weekend and you’re staying up later than when your heating is scheduled.
Manual Override
In the event that the Halo Lite PRT loses signal with the halo lite RF
receiver, you boiler or heat pump can be used manually while the issue is
resolved. If your PRT shows HL01 or your receiver RF LED is solid red, you can
slide the switch from Auto to Manual position.
Once in the manual position the Override button can be pressed to switch your
boiler / heat pump on and off while the lost connection issues can be
investigated. When Override LED is solid green then the boiler / heat pump
will be on, when no illumination then it will be off.
Note the position of manual mode is meant to be for temporary use only, once
the system is operating normally please ensure the switch is returned to the
Auto Position.
Plus Hours
If you are running a schedule with pre-set times (Auto mode) and you want to
maintain the current temperature of your heating instead of moving to the next
setting simply press the dial.
A pop up menu will appear for you to select how long you would like to extend
the temperature for, turn and push the dial to make your selection.
Push the dial to extend the current heating setting.
Turn the dial to select how long you would like to extend your heating for.
Push the dial or press the right button to confirm your selection.
The home screen will now display the override icon above the target
temperature.
TOP TIP
You could use this feature if you want to keep your heating on for longer than
is scheduled.
Maybe you’re not going to work today and you want your heating to stay on all
morning.
Schedules
Your Halo Lite RF will come with a pre-set schedule:
6:00 – 8:00 21°C
8:00 – 16:00 OFF
16:00 – 22:00 21 °C
22:00 – 6:00 OFF
You can alter this schedule by entering the “timed heating schedule” section
in the main menu.
Turn the dial to move between the different days and view the schedule that is
set. To edit a day, push the dial or right hand button when the day is
highlighted in light blue.
Push the dial to edit a heating time or temperature when it is highlighted in
light blue. You can also add an additional heating period by scrolling and
pushing on the “Add new heating event” bar. You can have up to six heating
events per day in your schedule.
TOP TIP
If you want to change more than one day you can use the copy day feature to copy the schedule from one to day to other days.
Alter the start and end times of the heating period and the temperature by
scrolling and then pushing the dial to edit. Then use the dial to alter the
time or temperature and push to confirm. Push the dial or the right hand
button to save your changes.
TOP TIP
Schedules help to balance comfort and energy efficiency, so you are heating your home to suit your lifestyle. Don’t forget you could set your weekend schedules differently to during the week if your routine changes.
ADDITIONAL FEATURES
Holiday Mode| To temporarily turn your heating off whilst you are on
holiday, select the holiday function in the menu and use the dial and buttons
to set the number of days.
---|---
Support Page| Provides information for your installer or technical
expert about your Halo Lite RF such as software version.
Child Lock| To lock the control to avoid it being altered press and hold
the left & right hand buttons at the same time until the icon appears. To
remove child lock press and hold the left & right hand buttons again.
Date & Time| If the date and time seen across the top of the screen is
incorrect you can alter this in the Date and Time section of the menu.
Advanced Settings| The Advanced Settings section of the menu allows your
installer or a technical expert to make adjustments and find information about
your Halo Lite RF.
Fault Notification| If there is a fault then the fault symbol will show
on the home screen of your Halo PRT. Press the left hand button to access
further information about the fault.
SYMBOLS
| Symbols | Name | Explanation |
|---|---|---|
| Flame | Indicates your heating is on | |
| Fault | Indicates there is a fault with the boiler | |
| Child lock | Child-lock is set so the PRT cannot be altered | |
| Override | Override or plus hours function is active | |
| Optimized start | Optimized start is active | |
| Delayed start | Delayed start is active | |
| Optimized stop | Optimized stop is active | |
| Frost protection | Frost protection is active | |
| Service due | Service due in: |
- 60 days (grey)
- 30 days (amber)
- 0 days (red)
| Hi| Room temperature is above 40oC
| Lo| Room temperature is below 0oC
| Target Temp| Temperature you want your heating to reach
| Current Temp| Room temperature in the location of your Halo PRT
| Time| Current time
| Date| Current date
| Battery| Battery status indication
| RF Communication| Indicates the Halo Lite RF is communicating with the
Receiver
WARRANTY
Your Ideal Halo Lite RF comes complete with a 2-year Ideal Guarantee, subject to the following terms and conditions.
During the period of the guarantee we will replace free of charge, where it suffers a mechanical or an electrical breakdown as a result of defective workmanship or materials, subject to the following conditions and exclusions;
- The guarantee will commence from the date of installation. Without proof of purchase the guarantee will commence from the date of manufacture (via serial number).
- The Installation needs to be registered within 30 days of installation, it can be registered online by visiting idealheating.com.
- If the control suffers a mechanical or an electrical breakdown we should be contacted on one of the following numbers:
- The guarantee does not apply:
a. To any defect, damage or breakdown caused by deliberate action, accident, misuse or third party interference including modification or failed batteries.
b. To any defect, damage or breakdown caused by the design, installation and maintenance of the central heating system.
c. To any other costs or expenses caused by or arising as a result of the breakdown of the controls.
d. To any defect resulting from the incorrect installation of the controls. To any costs incurred during delays in fixing reported faults.
Our Ideal Guarantee is offered in addition to the rights provided to a consumer by law. Details of these rights can be obtained from a Trading Standards Authority or a Citizens Advice Bureau.
Northern Ireland:
T: 02890 331444
Elsewhere in the UK:
T: 01482 498660
Our normal working times, excluding Bank Holidays, are:
8am – 6pm Monday to Friday
8am – 4pm Saturday
8am – 12 noon Sunday
Guarantor
Ideal Boilers Ltd, P.O. Box 103, National Avenue, Hull, HU5 4JN.
Consumer Helpline
T: 01482 498660
WEEE DIRECTIVE 2012/19/EU
Waste Electrical and Electronic Equipment Directive
- At the end of the product life, dispose of the packaging and product in a corresponding recycle centre.
- Do not dispose of the unit with the usual domestic refuse.
- Do not bu rn the product.
- Remove the batteries.
- Dispose of the batteries according to the local statutory requirements and not with the usual domestic refuse.
The code of practice for the installation, commissioning & servicing of
central heating systems
Hereby, Ideal Boilers Ltd declares that this device (model 237423) containing devices (237426 & 237448) is in compliance with: Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address idealheating.com
RF frequency: 868MHz
Max. RF output power: 10 dBm
UIN: 237464 A02
Customer Support
Ideal Boilers Ltd
National Avenue Hull, HU5 4JB
T: 01482 498660
E: enquiries@idealheating.com
idealheating.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>