wampat DJ0468BK 66 Inch Mid Century Modern TV Stand Installation Guide

wampat DJ0468BK 66 Inch Mid Century Modern TV Stand

FAQ

• Q: What should I do if I don’t have the wall attachment?
  • A: If the wall attachment is not included, please purchase a suitable one that fits your wall to prevent toppling. Seek professional advice if needed.
• Q: Can I assemble the TV table alone?
  • A: It is recommended to find a partner to help with the installation for efficiency and safety reasons.

IMPORTANT INFORMATION

Please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES

• In order to avoid scratching this furniture should be assembled on a soft layer-could be a rug.

IMPROVE EFFICIENCY!

• Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

WARNING

ANTI-TOPPLE WARNING!

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fit your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT

• It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly,and once every 3 months – in order to assure stability through-out the lifespan of the product.
• For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
• Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Board Identification

PARTS LIST

Please prepare the following tools

WARNING

• When installing, please carefully confirm whether each screw corresponds to the manual, accessories with similar shapes can be distinguished by size

PARTS

INSTALLATION INSTRUCTIONS

Remote Instructions

RF Wireless Remote Advanced

RGB LED Controller

• 22 Dynamic Modes
• 20 Dynamic Color
• Very Smooth Effects
• Speed Adjustable
• Brightness Adjustable
• Card Type RF Remote
• UltraSlim Design
• Dynamic Demo Mode
• Easy Remote Pairing
• Direct Color Select

Functions Instructions

• 1. Turn On/Standby
  • Press this key to turn on unit or switch to standby mode.
  • At poweron,unit will automatically turn on and restore to the previous status.
• 2/9. Dynamic Mode Adjust
  • Switch to dynamic mode from static color,or switch between dynamic modes.
• 3/10. Dynamic Speed Adjust
  • Adjust dynamic playing speed.Press SPEED+ to increase speed and press SPEÈD-to decrease.Unit will switch to dynamic model f press this key at static colormode.
• 4/5. Static Color Adjust
  • Switch to static color mode from dynamic mode ,or switch between static colors.
• 6. Direct Color Select
  • Shortcut key to static colors When press the specific color key,LED will play the same static color.The direct colors are included in ‘COLOR+’ and ‘COLOR-‘ operations.
• 7/8. Brightness Adjust
  • Adjust static color brightness.Press BRIGHT +to increase brightness and press BRIGHT to decrease.Unit will switch to static color model f press this key at dynamic mode.
• 11. Demo mode
  • Press this key will switch to Demo mode. At demo mode, it plays 17 dynamic modes in the loop,each mode repeat 3 times.

Installing

1. Power Supply
   • This unit accepts DC5V to24V power supply.The DC jack’s inner pole (or red cable) is positive and sleeve(or black cable) is negative. Also please make sure the powersupply voltage is same as the LED load,
2. LED Output
   • This unit support common anode connection LED products. The mark ‘ ‘ indicates the common connection node.

LED CONTROLLER

• The maximum constant current is 2amperesper channel.
• Please reduce load if main unit is overheating.

CAUTION: Do not short circuit or overload the LED outputs,this may lead to permanent damage!

Operation

1. Using Remote Controller

   • Please pull out the battery insulate tape before using.The RF wireless remote signal can pass through barrier,soit’s not necessary to aim at the main unit when operating.
   • For proper receiving remote signal,please do not install the main unit in closed metal parts.

2. Pairing New Remote
   The remote and main unit are 1 to 1 paired as default. Furthermore,main unit can be paired to 3 remote controllers and each remote controller can be paired to any main unit. Please do following steps to pair new remote controller:

3. Plug off the power of main unit and plugin after 5 seconds.

4. Press’SPEED-‘ and ‘SPEED+’key together in 5 seconds after power on. After this operation,the main unit will recognize the new remote controller.

5. Free Remote Pairing Mode
   In some specific cases, the main unit may need to be paired to any remote controllers.Please do the following steps for freere mote pairing mode:

6. Plug off the power or main unit and plug in afler 5 seconds.

7. press ‘ON/OFF’ and ‘MODE + key together in 5 seconds after power on.

  * After this operation, the main unit will recognize any remote controller.
  * To pair the main unit back to specific remote,please repeat the Pairing New Remote operation.

Switch Output Color Sequence

The control Icr’s default output signal sequence is Common-Green-Red-Blue.lf the LED application is in different cable sequence, the direct color keys will not match the LED color.
In this case, user can adjust the output signal sequence with following steps:

1. Plug off the power of main unit and plugin after 5 seconds .
2. Press’RED’and’BLUE’color key together in 5 seconds after power on.
   • With this operation,the output sequence will switch between 6 possible combinations.The sequence will be memorized and it won’t change before next same operation.

Specification

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>