ebay AN-5004 Digital HDTV Antenna User Manual

ebay AN-5004 Digital HDTV Antenna

Product Information

Specifications:

• Frequency Range: VHF 174-216MHz; UHF 470-806MHz
• FCC Compliance: Part 15 of FCC Rules

Product Usage Instructions

FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FAQ (Frequently Asked Questions)

• Q: What is the frequency range of this product?
  A: The frequency range of this product is VHF 174-216MHz and UHF 470-806MHz.

• Q: What does FCC compliance mean?
  A: FCC compliance indicates that this product meets the regulations set by the Federal Communications Commission to ensure proper operation and minimal interference.

Model: AN-5004
USER MANUAL Digital HDTV Antenna

Package contents

Parameters

1. Frequency range: VHF 174-216MHz; UHF 470-806MHz
2. VSWR: ≤2. 0
3. Impedance: 750
4. Gain: 28dB
5. Connector: F Male or Customized
6. Power supply : USB port (5V/500mA)
7. Polarization: Horizontal / Vertical

Antenna Connection

• Connect to Set-Top box(STB

• Connect directly to HDTV

1. Connect coaxial cable of power box to the ANT/IN or CABLE IN port on the back of TV/STB.
2. Plug the power box’s USB connector into an open USB port on the back of TV/STB or into a wall outlet using power adapter to ensure amplifier works properly.

Antenna installation

1. Install with screws(Recommended for outdoor use)
   • The distance between the two markers should be 53 millimeters.
   • Fix the screws to the wall with a hammer
   • Hang the antenna on the screw
2. Mount with stickers(Recommended for indoor use)
   • Clean the walls and put stickers on them.
   • Make antennas and stickers fit tightly.
   • The sticker is stuck on the mounting hole.

Scan for Channels

1.  In the TV’s setup menu, set the mode to Antenna or Air. Refer to the TV manual for detailed instructions.
2. While in the TV’s setup menu, set TV to scan for channels. This can sometimes be listed as auto-program, channel search or channel scan. Consult your TV manual for detailed instructions.

FAQ

• Q: Will all the channels I receive be High Definition (HD)?
  A: Not all digital signals are High Definition(HD). Make sure you are using a High Definition Television(HDTV) with built in ATSC tuner. When connecting the antenna to a third-party receiver, make sure it is capable of receiving HD. Otherwise no HD channels can be picked up.

• Q: Can you put the antenna behind the TV?
  A: Yes, but it may not be the ideal location for the antenna. The TV will block some of the signal, which will weaken the signal.

• Q: Are channel lineups available?
  A: No. The channels you can receive depend on many complex factors such as distance to the transmitting antennas, your height above ground, the compass reading, trees blocking a clear view, etc. The good news is that once you use scan function of your TV you will see what channels were found.

• Q: Is this just like a freeview box?
  A: No, it’s just an aerial that plugs into back of your freeview-enabled TV, so you can have a TV anywhere in house without having to run cables all over the place. Works a treat and we can get all the usual freeview channels including digital radio in the spare bedroom

• Q: How many channels can I receive?
  A: The number of channels you can receive will be determined by what is being broadcast in your area. Channel reception will vary from location to location based on terrain (including trees, buildings, hills and mountains The fewer obstructions, the better your chance of receiving strong digital signals. Go to http://dtv.gov/maps. Enter your address for a listing of likely channels available in your area.

Troubleshooting

1. Check to make sure you have correctly connected the antenna to your HDTV or third-party HD receiver.
2. Reposition the antenna in a different location. Maybe higher on a wall or close to a window ? Facing the direction of the broadcast tower is usually best. Signal strength will vary based on certain conditions. Distance from the tower, hills, buildings and even tall trees can impact reception. Always re-scan for channels after moving the antenna.
3. If a channel is missing, try turning the antenna 10 or 20 degrees in either direction to avoid reflection or move the antenna, and then re-scan the channel.
4. The picture or sound freezes while I am watching a channel, or there are boxes in the picture. This is often caused by a weak or intermittent signal. Try moving the antenna to a different location or aiming it in the direction of the broadcast tower for that channel.
5.  Not all digital signals are High Definition (HD). Make sure you are using a High Definition Television (HDTV) with built in ATSC tuner. When connecting the antenna to a third-party receiver, make sure it is capable of receiving HD. Otherwise no HD channels can be picked up.

Model : AN-5004

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>