Pinkoi sanag S2S OWS Bluetooth Headset User Guide
- July 19, 2024
- Pinkoi
Table of Contents
Pinkoi sanag S2S OWS Bluetooth Headset
USER MANUAL
MODEL: sanag S2S /sanag S2S Al
Product Overview
Key function operation
-
Power on:
1. Automatic power on: open the charging box and take out the headset.
2.Manual boot Press and hold the MFB touch button for 3 seconds. The Ice blue llght bllnks quickly, the auxiliary ear light is off after the connection, and the ice blue light of the main ear blinks to be connected. -
Shutdown:
1. Put the earphone into the charging case and automatically shut down.
2. Hold down the MFB touch button for about 7 seconds, and then tum off the Ice blue Ilg ht after three quick flashes. -
Pairing: After the headset is turned on, it automatically enters the pairing state (waiting to be connected with the mobile phone), the ice blue light of the main ear flashes, and the auxiliary ear light ls off.
-
Answer: When a call comes in, click the MFB touch key of the left end right ears
-
angup: During the call, double-click the MFBtouch button of the left and right ears
-
Reject: When a call comes in, press the MFB touch key for 2 seconds
-
Play/Pause: CIiek the left end right ear MFB touch keys
-
Previous: Double cllck MFB touch button on left eer
-
Next: Double click MFB touch button on right ear
-
Volume plus: Hit left ear MFB touch key three times
-
Volume reduction: hit the right eer MFB touch key three times
-
Voice Assistant: Press and hold the eer MFB touch button for about 3 seconds to release the voice assistant end click to exit
-
Reset headset: When the phone is not connected, press the MFB button of the left and right ears at any time to reset the headset factory Settings, and the ice blue light will tum off eutometically after 2 seconds of successful reset.
-
Geme Mode/Music mode: Hit the MFB button of the left end right ears 4 times to enter the low latency mode, and then switch to the music mode 4 times.
-
Low power alarm: When the headset battery is insufficient, it will prompt a low power alarm tone every 3 minutes.
-
Charging: Put the earphones Into the charging case, chergethe earphones, the lee blue Light will tum on, end the earphones will tum off when they ere full. Charge the charging box, the warehouse ice blue light flashes, and the full ice blue light is on.
Bluetooth operation
Bluetooth connection is successful:
1. The headset enters Bluetooth mode, end the phone searches for the
Bluetooth pairing name “seneg S2S /seneg S2S Al”.Cllck on the connection.
2. The headset connects to the device once by default
Bluetooth disconnected:
1. Manually tum off the Bluetooth of the mobile phone, and the headset enters
Bluetooth pairing mode.
2. After the headset Is disconnected from the Bluetooth of the mobile phone,
rt will eutometically shut down after 5 minutes.
Specifications
- Name: OWS Bluetooth headset
- Model: sanag S2S /sanag S2S Al
- Bluetooth version: V 5.3
- Connection range: ii!:1 Om
- Charging voltage: 5V=1A
- Earphone battery capacity: 35rnAh/0.129Wh
- Charging compartment battery capacity: 400mAh/1.48Wh
Matters needing attention
- Do not use abrasive cleaners to clean this product.
- Do not allow this product to be heated or close toe fire source, such as a cooking stove.
- Do not expose the product to direct sunllght fore long time.
- Do not discard this product in fire to avoid explosion.
- Do not attempt to disassemble this product to make any modifications, as it does not contain any maintenance components.
- Do not use this product In rain.
- If you do not plan to use this product fore long time, please store it in e dry environment and charge the headset at least once a month to extend its life and avoid extreme temperatures and dust.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Arly Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has bean tasted and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/1V technician for help.
The device has bean evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC ID:2A6MS-S2S
Documents / Resources
|
Pinkoi sanag S2S OWS Bluetooth
Headset
[pdf] User Guide
2A6MS-S2S, 2A6MSS2S, sanag S2S OWS Bluetooth Headset, sanag S2S, OWS Bluetooth
Headset, Bluetooth Headset, Headset
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>