Desky SP-SSD-WN01 Electric Sit Stand Desk Instruction Manual

Desky SP-SSD-WN01 Electric Sit Stand Desk

Product Information

Specifications

• Product Name: Electric Sit-Stand Desk
• Model No.: 3015282 SP-SSD-WN01
• Height Adjustment Range: 72~120cm (28.3~47.2 inches)
• Anti-Collision Sensitivity Levels: 0~8

Product Usage Instructions

Safety Instructions

Electrical Safety Instructions

CAUTION

• To avoid burns, fire, and electric shock, read the instructions carefully.
• Do not clean the product with water while the power is connected.
• Do not disassemble or replace components with the power connected.
• Do not operate the system with a damaged cord or plug; contact support for replacements.
• Avoid operating the system in moist environments or with electrical components in contact with liquids.
• If the control box makes noise or odor, do not operate the system. No alterations to power unit or control box allowed.

Other Safety Instructions

CAUTION

• Follow troubleshooting guide for errors like E01, E07, etc.
• If system overheats, allow it to rest for 18 minutes before operation.
• If columns don’t align, reset the system.
• Check for broken hall wires and replace motor cords if necessary.
• Remove overload on the desk to prevent motor failure.
• If desk moves in the wrong direction, check connections or replace motor cords.
• If memory cannot be read, unplug and replug. If issue persists, replace the control box.
• In case of collision avoidance system failure, replace the control box.

Custom Programming Guide

Button Functions

• Adjust
• Confirm/ Next/Save
• Back/Cancel

To Adjust Minimal Height Limit:
(72~110cm/28.3~43.3)

To Adjust Maximum Height Limit:
(82~120cm/32.3~47.2)

To Adjust Anti-Collision Sensitivity (Current Sensor Upward Movement) (Level 0~Level 8):

1. Step 1: Preparing
   Press M and T buttons simultaneously for about 5 seconds until the unit emits one beep and the display flashes S-1. Press UP/Down button to switch between settings. The custom mode will be active for approximately 10 seconds.

2. Step 2: Programming
   Set your desired height limits and anti-collision sensitivity levels by following the on-screen instructions for S-1, S-2, and S-3 settings.

3. Step 3: Saving
   Press M to save your settings. The display will show successful or failing status after saving.

Frequently Asked Questions (FAQ)

• Q: What should I do if my desk overheats?
  A: Allow your desk to remain idle for approximately 18 minutes before resuming operation.

• Q: How can I adjust the height limits of my desk?
  A: Follow the custom programming guide provided in the manual to adjust the height limits.

• Q: What should I do if my desk moves in the wrong direction?
  A: Check the connections or replace the motor cords as instructed in the troubleshooting guide.

ELECTRIC SIT-STAND DESK

Instruction Manual
Item No.: 3015282
SP-SSD-WN01

Instructions of Safety and Warnings:

• Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
• Overlooking any part of the instructions, warnings and additional information marked with the “Note” and ” may result in serious damage to the system or its components.
• Children should never be allowed to operate or touch the product without direct supervision of an adult. Users should prevent children from being near or around the desk during operation.
• Disabilities and/or lack of experience and knowledge should be prevented from using the product unless under supervision or assisted during use and operation.
• Never sit on or exceed the rated weight of the desk.

Electrical Safety Instructions:

The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the instructions carefully.

• Don’t clean the product with water while the power is still connected.
• Don’t disassemble or replace components while the power is still connected.
• Never operate the system with a damaged cord or plug. Please contact your point of purchase to replace the damaged parts.
• Never operate the system if it’s in moist environment or its electrical components have contact with liquids.
• Don’t operate the system if the control box makes noise or odor. Alterations of the given power unit and control box aren’t allowed.

Other Safety Instructions:

• Remove any obstacles from the area around the desk during assembly and subsequent use.
• Organize all cords and wires to prevent any possible tripping or accidents from occurring.
• Never attempt to modify or change the desk frame or components that operate the desk.
• Don’t add anything to the adjustable junctions of the desk frame.
• The desk is rated for Indoor Use Only.

Troubleshooting Guide

approximately 18 minutes.
E02| The columns don’t go together. Reset the system.
E04| System’s communication has an error. Plug out the power and re-plug.
E05| Collision avoidance system has activated. Remove all the objects within the range of motion.
E06| Electrical problem has occurred. Plug out the power and re-plug. If it doesn’t work, replace the control box.
E08|

• Collision avoidance system has activated. Remove all the objects within the range of motion.
• The control box isn’t placed well. Please make sure the control box is properly attached to the desk frame as the instruction manual or placed well on the even surface.
• The power cords have pulled the control box. Manage the cables and keep them from pulling the control box.

E11| The motor cords were disconnected, Check the connection or replace the motor cords.
E12| Electrical problem has occurred. Plug out the power and re-plug. If it doesn’t work, replace the control box.
E13| Motor wires may be broken. Check the connection or replace the motor cords.
E14| Hall wires may be broken. Check the connection or replace the motor cords.
E15| Short circuit. Replace the motors or columns.
E16| Overload leads to the motor to fail to drive. Remove the items from the desktop then reset the system.
E17| Desk move in wrong direction. Check the connection or replace the motor cords.
E18| Overload has occurred. Remove the items from the desktop.
E42| Memory can not be read. Plug out the power and re-plug. If it doesn’t work, replace the control box.
E43| Collision avoidance system failure. Replace the control box.

Custom Programming Guide

Checklist and Installation

Please check all of the components shown in the component checklist. If any of the components are missing or damaged, contact your point of purchase for a replacement.

What important specifications should know before installation?

What tools are needed to assemble the desk frame?

Attaching the Lifting Column

• Carefully place Desktop A upside down on the floor as shown.
• Attach the Lifting Column C to the Desktop using Screws S-A with Allen Wrench S-E.
• Tear off the adhesive tapes.

Note: Please make sure the desktop pieces keep facing down while installation.

Attaching the Feet

• Attach the Feet D to the Lifting Column using Screws S – A
• Attach the Hook B to the backside of desktop using Screw S – B .

Connecting Cords and Attaching the AC Adapter

• Connect the Controller with the AC Adapter and motor as shown.
• Insert the Power Plug S – D into the AC Adapter.

Note: Do not plug into the power before the desk is fully assembled.

Cable Management

Attach the Cable Ties S- C to the desktop with Screws S-B , and then organize the cables for a clean look.

Adjusting the Desk

• Turn over the desk with the help of another person.
• There are two adjustable foot pads under each foot. If the floor isn’t even, simply turn the pad to adjust the level to make the desk stable.

Tip: Use a bubble level (not included) to check if the desktop is even.

CAUTION: At least two people are required when turning over the desk, or serious bodily injuries might occur.

Operating Control Panel

Note: If the control panel is used for the first time, please reset the system before any normal operation. Reset the System:

Reset the System:

• To reset the system, press and hold the “Up” and “Down” buttons simultaneously. After five seconds the display shows “ ” and the desk start moving downward and to the lowest position. Never release the buttons until the unit emits one beep. The desk will move upward a little and the display shows the current desk height. The reset process is finished.

Height Adjustment: Press and hold the “UP”/”DOWN” button to lift/lower the desk to your desired height. Press and release the button to lift/lower the desk precisely.

Timer:

• Press the “T” button to set the period of time to inform users to stand up. Each press of the “T” button leads to an 0.5 hour increment. The maximal setting of time is 2 hours. After setting a period of time, the display will flash for seconds and it will automatically return to show the height of the desk. Then the indicator light on the top right of panel will be on.
• The unit emits 5 beeps to remind the users when the set time is up.
• To cancel the timer, repeatedly press the “T” button until the display shows the current height and the indicator light is off.

Memory Setting

• To store a memory position, press “M” button and the display will flash ” “. While the “S-” is displayed, press the button 1 or 2.
• To call a stored position, press memory button 1 or 2 and the system will start moving to the desired memory position. The display will count the height as it is driving to the memory position. Press any button to stop the motion.

Screen Locking Function:

• For safety reasons this control panel has a locking function. To activate / cancel the locking function, follow the “PART3-Custom Programming Guide: To Change the Screen Lock Function”.
• To lock the control, press “M” for 3 seconds. If the control is locked, only a bar ” ” is lighting in the display and any operation is invalid.
• To unlock the control, press “M” for 3 seconds. The height will be shown in the display. Switch measure between CM and INCH: The preset measurement shown on the display is cm. If you would like to change cm to inch, press the button ” T ” for 8 seconds. After the buzzer beeps twice, the measurement is successfully reset. If you would like to switch inch back to cm, press the button ” T ” for 8 seconds. After the buzzer beeps once, the system is successfully switched to cm measurement again.

Switch measure between CM and INCH:

• The preset measurement shown on the display is cm. If you would like to change cm to inch , press the button “ T ” for 8 seconds.
• After the buzzer beeps twice , the measurement is successfully reset . If you would like to switch inch back to cm , press the button “ T ” for 8 seconds.
• After the buzzer beeps once , the system is successfully switched to cm measurement again.

Power-saving Mode
The system will enter into power-saving mode with display becomes dark when no actions for over 10 minutes.
Touch any button to activate the control panel.

USB Charging Port:
The total power output of the USB-A & USB-C ports is max. 5v/3a. Charging is suspended while the product is running.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>