Ronix 3220 Angle Grinder Instruction Manual
- July 16, 2024
- Ronix
Table of Contents
Ronix 3220 Angle Grinder
Specifications
- Model: 3220
- Power: 2400W
- No-load RPM: 6000
- Voltage: 220-240V
- Frequency: 50-60Hz
- Wheel Diameter: 230mm
- Spindle Size: M14
- Weight: 5.4Kg
Product Information
The Angle Grinder 3220 is a powerful tool designed for various cutting and grinding applications. It features a robust construction with a high-power motor and essential safety features.
Product Usage Instructions
Safety Precautions
- Keep work area clean and well-lit.
- Avoid using the tool in damp or wet locations.
- Avoid electric shock by not touching grounded metal surfaces.
- Keep children and visitors away from the work area.
- Store the tool in a dry and secure place when not in use.
- Avoid overloading the tool and always use the right tool for the job.
- Dress properly and wear safety goggles and appropriate attire.
- Avoid abusing cables and maintain proper balance during operation.
- Maintain tools with care by keeping them clean and following maintenance instructions.
Basic Operation
- Before starting the tool, ensure the work area is safe and secure.
- Attach the cutting blade securely to the spindle using the provided accessories.
- Plug in the tool to a suitable power source matching the voltage requirements.
- Hold the tool firmly with both hands, one hand on the main handle and the other on the side handle.
- Activate the switch to start the tool and adjust the speed as needed for the task.
- Avoid applying excessive force and let the tool work at its intended rate.
Frequently Asked Questions (FAQ)
-
Q: Can this angle grinder be used for cutting metal?
- A: Yes, the angle grinder can be used for cutting various materials including metal. Ensure you use the appropriate cutting blade for metal cutting applications.
-
Q: How do I change the cutting blade on the angle grinder?
- A: To change the cutting blade, first, disconnect the tool from the power source. Then, use the provided spanner to loosen the spindle nut, remove the old blade, and securely attach the new one before tightening the nut.
-
Q: What safety gear is recommended when using the angle grinder?
- A: Safety goggles, protective clothing, and appropriate footwear are recommended when operating the angle grinder. Additionally, using a dust mask is advised when working in dusty environments.
WINKELSCHLEIFER
3220
TECHNICAL SPECIFICATION
| Model | 3220 |
|---|---|
| Power | 2400W |
| No-load RPM | 6000RPM |
| Voltage | 220-240V |
| Frequency | 50-60Hz |
| Wheel Diameter | 230mm |
| Spindle Size | M14 |
| Weight | 5.4Kg |
| includes00 | Auxiliary Ronix Design Handle, Ronix wheel Guard, Spanner |
PART LIST
WARNING!
When using electric tools, All the safety instructions should always be
observed to reduce the risk of fire, electric shock and personal injory before
attempting to operate the tools, Please read all the instruction and save it
FOR further reference.
BASIC SAFETY PRECAUTIONS FOR ALL ELECTRIC TOOLS
KEEP WORK AREA CLEAN
Cluttered area and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT
Don’t use electric tools in damp or wet locations . Don’t expose electric
tools to rain. Keep work area well-lit in particular, no inflammable liquids
or gases must be present.
AVOID ELECTRIC SHOCK
when you are operating tools, don’t touch metal being grounded, such as
pipe, radiator, freezer, etc.
KEEP CHILDREN AND VISITORS AWAY
Don’t let children contact tool or extension cord. All visitors should be kept
away from worl place.
STORE IDEL TOOL
when not is use , tools should be stored in dry , high, or locked place.
DON’T FORCE TOOL
It will do the job better and safer at the rate for which it was intended,
Avoid unnecessary overload which may put the operator at risk and impair
functions of the tools.
USE RIGHT TOOL
Don’t force small tools and attachment to do the job of a heavy duty tool.
Don’t use tools for purpose not intended, for example , don’t use electric
circular saw for cutting logs or tree limbs.
DRESS PRPPERLY
Don’t wear loose clothes or jewelry . they can be caught in moving parts.
Rubber gloves and non skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
USE SAFETY GOGGLES
Always wear safety goggles. If dust is produced, use the special masks.
DON’T ABUSE CABLES
Never carry tool by cable or yank it to disconnect it form socket. Keep cable
from heat, oil and sharp edges.
DON’T OVERREACH
Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and chaining accessories. Inspect tool cords
practically and replace if damaged. Keep handles dry, clean and free from oil
and grease.
DISCONNECT TOOLS
When not in use, before servicing, and when chanting accessories such as
blades, bits and cutter.
REMOVE ADJUSTING KOYS AND WRENCHES
From the habit of checking to see that keys and adjusting wrenches are removed
from tool before turning it on.
AVOID UNINTENTIONAL STARTING
Don’t carry plugged-in tool with finger on switch . Make sure switch is off
when connecting the plug to the socket.
USE EXTENSION CORD
If an extension cord is required, always check that its cross-section
measurement is equal to or greater than that of the tool capabilities and so
marked.
STAY ALERT
Watch what you are doing . Use common sense. Do not operate tool when you are
tired.
CHECK DAMAGED PARTS
before further use of the tool, a guard or other parts that is damaged should
be carefully checked to determine that it will operate properly and perform
its intended function . Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other condition that may affect its
operations. A guard or other part that is damaged should be properly repaired
or replaced by a qualified service center. Do not use tool if switch does not
turn on and off.
CHECK THE VOLTAGE
Do not plug the electric tool into the mains until you have checked that the
voltage shown on data plate corresponds to the voltage available.
REPLACE PARTS
The use of improper accessory or attachment other than recommended present a
risk of personal injuries.
HAVE YOUR TOOL REPAIRED BY AN EXPERT
This electric tool is in accordance with the relevant safety regulations ,
Repining of electric tool may be carried out only by expert , otherwise, it
may cause considerable danger of the user.
STRUCTURE AND FUNCTIONS
The angle grinder is hand-held class II electric power tools with double-
insulated structure. Driven by single phase series motor , and with speed
reduced by a pair of spiral bevel gears, the series of tools are widely used
for removing burrs from surface of metal part, beveling and fishing weid
seams, cutting thin wall tubes and small size metal material, etc in the
fields of machines builing, vehicle manufacturing, chemical engineering . If
with its working head changed, this series of tools also is used to clean rust
and polish the surface of metal and other material.
ADDITIONAL SAFETY REGULATIONS
- Operator is recommended to wear goggles when operating the tool.
- When operating , the cable of the tool and its extended wire must be placed at the back side of the tool in order to avoid the cable or extended wire being damaged.
- During operating don’t hit work piece with grinding disk, when the tool is used to cut small work piece, it mustn’t vacillate to the left and right in order to avoid disk being broken. In order to get good result, the slope between the disc and the working surface should be tilted at the angle of 15-30.
- when moving the tool, the user should hold its bobby or its handle, never drag the tool by its cable.
- Before using the tool, the tool should be checked to make sure wheatear the disk guard is in good condition and is fasten tightly. The tool without guard is not allowed to be used.
- Before using the tool, please make sure that the disc-installing disassemble button has been in “0”position , and whether the main spindle of disc of disc can rotate flexibly.
- It is prohibited to use the disk installing disassemble button as a brake button when the tool is rotating, otherwise , the tool will be damaged and injury may occur to a person.
- It is important for you to select fiber reinforced cymbal type disc whose safety speed is not less than the no load rated speed. It is prohibited to use the disc whose diameter is bigger than that of rated size. The no load speed of this series of tools, please see to the list attached.
- When making inspection, adjustment , and disc changing to the tool, does make sure that the plug of the tool has been pulled out of power socket. 10- Before operating the tool, please make sure whether the disc has a breakage or a crack , it shouldn’t give a voice of breakage or crack when knocked slightly by a wooden hammer.
OPERATION REGULATIONS
SIDE HANDLE
Please use side handle for safe and convenient operation.
The side handle can be installed easily in one of the holes on the side of the
angle grinder.
DISK PROTECT GUARD
WARNING!
-
Before Installing or disassembling the disc, Please make sure the switch is in “0” position and the plug is not connected with socket.
To put the protruding position of protect guard into the slot an front cover, then turning 180 clockwise or anticlockwise. -
Fix the screw on protect guard until tightened.
HOW TO CHANGE THE DISC
WARNING!
- Before installing or disassembling the disc, please make sure the switch is “0” position and the plug is not connected with socket.
- The max speed of the disc installing 4800 m/min.
- Fix the inner flange onto the spindle, then put the disc onto the inner flange. After that-put the out flange on the spindle.
- Press the spindle lock on the gear box, screw the out flange with the flange spanner include in the accessories until the out flange is fastened tighty.
- You can also install or disassemble the disk with two spanners, with one spanner to be installed to upper part of flange to lock the main shelf, and with another spanner to disassemble the flange nut.
WARNING!
the spindle lock is only used to install and disassemble the disc of the tool.
It is prohibited from being used as a brake button when the tool is rotating.
Otherwise the tool will be damaged and injury may occur to a person.
SWITCHED “ON”AND”OFF” OPERATION
WARNING!
- Before plug the angle grinder into the power socket, please make sure the spindle ock is on “0”position.
- To turn the angle grinder into switch “I” position, then the tool start running.
- To switch the angle grinder into switch “0” position, then the tool stops.
EFFECTIVE AND SAFELY WORKING METHOD
WARNING!
-
It is prohibited to use the tools without the protect guard-To lay down the tools, please make sure the switch is on “0” position and the disc stopped.
-
A Use the correct position on disc, otherwise the disk will be damaged.
-
B To put the strength approximately ½ weight of the tools itself, then you could get an satisfied effect.
Using the tools with too much force will overload the tool and get the motor and disk damage. -
C In order to get good result the slope between the disc and the working surface should be titled at the angle of 15-20.
-
-
D when using new disc, don’t move the tools in B direction , otherwise the work piece maybe cut off. After the disc become round , then the tools could be moved in both A and B directions.
SERVICE AND MAINTENANCE
- Always disconnect the tool before carrying out inspection or cleaning Never use water or other liquids to clean the tool. Clean the tool by brushing it with a brush.
- The air vent of the tool should be cleaned regularly to avoid the motor too hot due to air vent blocked.
- Always check if the components of the tool are fixed well.
- The housing should be without trace of crack or damaged.
- Always check if the cable is without damage.
REPLACING THE CARBON BRUSHES
- Replacing the carbon brushes , when the tool couldn’t run or too much sparkle.
- Carbon brushes which are worm out(burned. Broken or shorter than Smm have to be replaced by new ones.
- Always replace both carbon brushes at the same time and sure the brush by original manufacturer.
- Because the carbon brush is internal, so please change the brushes by our maintenance service center.
- After placing the new carbon brushes, let the tool run for some minutes so that the brushes fit better.