Sunco DL_SMDR56-13W-27K_5K 6 LED Retrofit Selectable Smooth Downlight User Manual

Table of Contents

User Manual
6″ LED Retrofit Selectable Smooth Downlight
SKU: DL_SMDR56-13W-27K_5K

Retrofit Downlight

Safety Information

To reduce the risk of fire, electric shock, or physical injury:

Turn off circuit breaker before installing this fixture.
This product should be installed by a person familiar with the construction and operation of the product the hazards involved. Safety eyeglasses and gloves are recommended.
Abide by related regional and local laws or regulations.
Proper grounding is required to ensure safety.
Do not alter, relocate, or remove wiring during installation.
Do not make or alter any open holes in wiring enclosure or electrical components during installation.
Check for shipping damage before insatalling. If the product is damaged, do not use it.
Keep fixture away from corrosive substances.
Suitable for damp locations at temperature ranging from 4°F to 104°F. Not for use where directly exposed to water.
Clean the fixture regularly to ensure proper operation. Do not clean with harsh solvents.
Use safety precautions and abide by regional and local laws or regulations.
This product is not compatible with 3rd party sensors.
This product is not compatible with photo controls.
This product is not compatible with occupancy sensors.
This product is not compatible with timing devices.

WARNING:
Cancer & Reproductive Harm- www.P65Warnings.ca.gov

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.

Quickstart Guide

STEP 1
a. Turn off circuit breaker before installation.
b. Locate the housing.
NOTE: Remove previous fixture. Fixture may be hot so allow time to cool after turning off power.
STEP 2
Secure the clip springs firmly within the retrofit connector.
(Caution: Avoid excessive force when holding down the spring. If the spring is not locked, attempt to resolve the issue by turning it over.)
STEP 3
Determine the type of connector available.
TP24 Connector(1) -E26 Base(2)
STEP 4
a. Connect the appropriate adapter to make connection in the housing.
NOTE: the wires may come lose from the connectors soensure they are attached.
b. Tuck all wires into the can.
STEP 5
a. On back of retrofit fixture, slide the CCT Selection Switch to choose from five color temperatures. Try each CCT to determine best fit.
b. Turn off light switch after selecting your choice and continue install.
STEP 6
- a. Line up trim ring with opening.
- b. Push downlight into can until secure. Compression clips will hold retrofit light in place. Push up springs into can clips.
- c. Turn on circuit breaker and test light.

Recommended Dimmers

Scan for the full compatible dimmer list

Voltage	120V	Average Lifetime	50000 hrs
Wattage	13W	Lumens	965LM
Wattage Equivalency	120W	Moisture Rating	Damp
Beam Angle	90°	CRI	80+
Weight	0.3lbs	Usage	Indoor
Housing Material	PC	IC Rated	Yes
Dimmable	Yes	Warranty	7 Years

Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts are happy to help brighten your day.

Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles:
A symmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a certain degree in up-lighting.
An asymmetric lighting distribution angle, also known
as beam angle, creates a pattern that focuses light in a specific direction. This type of lighting is ideal for task lighting as it reduces glare and light spill in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums,
and much more.
It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.