sentiotec 1-053-078 Onni Mini Infrared Cabin User Manual
- June 12, 2024
- sentiotec
Table of Contents
- sentiotec 1-053-078 Onni Mini Infrared Cabin
- Product Information
- Product Usage Instructions
- Important information for your safety
- Product description
- Technical data
- Preparation for assembly
- Circuit diagram
- Operation
- Assembly illustrations
- Spare parts
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
sentiotec 1-053-078 Onni Mini Infrared Cabin
Product Information
The product is an Infrared cabin called Onni Mini (1-053-078). It is designed for heating the human body. The cabin is equipped with IR radiators and dimmable heating elements on the sides, calves, and floor. The cabin is intended for use on a level surface with a minimum distance of 5 cm from the wall. It is important to follow the safety information and warning notices provided in the user manual. The product has been produced in accordance with applicable safety regulations. For installation and use, it is recommended to read the instruction manual carefully and keep it within reach of the infrared cabin for reference. The manual can also be found on the manufacturer’s website for download.
Product Usage Instructions
- Ensure that the cabin is placed on a level surface with a minimum distance of 5 cm from the wall.
- Before installation or connection of electrical parts, disconnect the power supply to ensure safety.
- Comply with the regulations applicable at the installation location.
- The cabin should not be used by children under 8 years old.
- Children over 8 years old, persons with limited psychological, sensory, or mental capabilities, or persons with lack of experience/knowledge can use the cabin under certain conditions:
- Children should not play with the cabin.
- Children under 14 years of age can only clean the cabin under supervision.
- Do not clean the cabin with steam cleaners, high-pressure cleaners, or splashed water.
- Avoid using the sauna when under the influence of alcohol, medication, or drugs for health reasons.
- Before switching on the control unit, ensure that no combustible objects have been placed on the heating elements.
For more detailed information on assembly, circuit diagram, operation, guarantee, and spare parts, refer to the respective sections in the user manual.
About this instruction manual
Read these installation and operating instructions carefully and keep them
within reach of the infrared cabin. This ensures that you can refer to
information on safety and operation at any time.
- These installation and operating instructions can also be found in the downloads section of our website: www.sentiotec.com/downloads.
Important information for your safety
The infrared cabin has been produced in accordance with the applicable safety regulations for technical units. However, hazards may arise during use. Therefore adhere to the following safety information and the specific warning notices in the individual chapters.
Intended use
The infrared cabin is used for the heating of the human body. The cabin
location must be protected against splashing water. For optimal operation, the
location should have an ambient temperature of at least 20 °C. The maximum air
humidity in the surroundings should not exceed 95%. The cabin must be erected
on a level surface. A distance of at least 5 cm from the wall must be
maintained. Any use exceeding this scope is considered improper use. Improper
use can result in damage to the product, severe injuries or death.
Safety information
- Installation and connection of the electrical parts (control unit, heater, etc.) may only be performed when the power supply is disconnected.
- Also comply with the regulations applicable at the installation location.
- For your own safety, consult your supplier in the event of problems that are not explained in sufficient detail in the installation instructions.
- The cabin may not be used by children under 8 years old.
- The cabin may be used by children over 8 years old, by persons with limited psychological, sensory or mental capabilities or by persons with lack of experience/knowledge only under the following conditions:
- They are supervised.
- They have been shown how to use the device safely and are aware of the hazards that could occur.
- Children may not play with the cabin.
- Children under 14 years of age may only clean the cabin if they are super-vised.
- The cabin may not be cleaned with steam cleaners, high-pressure cleaners or splashed water.
- For health reasons, do not use the sauna when under the influence of alcohol, medication or drugs.
- Before the control unit is switched on, make sure that no combustible objects have been placed on the heating elements.
Product description
Technical data
| Cabin material | Abachi |
|---|---|
| Cabin dimensions (L x W (depth) x H) | 1000 x 1043 x 2000 mm |
| Voltage supply | 230 VAC 50 Hz |
| Total output | 1400 Watt; 6.1 A |
| IR radiator, dimmable | 1 × 400 W |
| Heating elements, sides | 2 × 300 W |
| Heating element, calves | 1 × 200 W |
| Heating element, floor | 1 × 200 W |
Floor plan
Scope of delivery
Parts list
| No. | NAME | DIMENSIONS | PIECES |
|---|---|---|---|
| 1 | Roof cover | 914 x 954 x 5 mm | 1 |
| 2 | Roof element | 914 x 954 x 65 mm | 1 |
| 3 | Rear wall | 914 x 1980 x 59 mm | 1 |
| 4 | Right side wall | 1013 x 1980 x 46 mm | 1 |
| 5 | Left side wall | 1013 x 1980 x 46 mm | 1 |
| 6 | Glass front | 1000 x 2000 x 67 mm | 1 |
| 7 | Heating element, side | 460 x 878 x 40 mm | 2 |
| 8 | IR radiators | 250 x 780 x 65 mm | 1 |
| 9 | Ergonomic bench | 914 x 550 x 80 mm | 1 |
| 10 | Bench support | 914 x 510 x 60 mm | 1 |
| 11 | Heating element, calves | 914 x 390 x 40 mm | 1 |
| 12 | Heating element, floor | 670 x 340 x 55 mm | 1 |
| 13 | Ergonomic backrest | 800 x 870 x 111 mm | 1 |
| 14 | Door handle | 1960 x 80 x 32 mm | 1 |
| 15 | Floor grid | 914 x 954 x 46 mm | 1 |
| Screws | 4 x 35 mm | 14 | |
| Screws | 5 x 60 mm | 4 | |
| Screws | 4 x 35 mm | 8 |
Preparation for assembly
Before you begin work, check the parts list to ensure that all the individual parts have been delivered. If you discover any missing parts, notify your dealer within 14 days of receiving the sauna cabin.
-
You need an assistant for assembly. We also advise you to pre-drill the holes for the screws
-
Check the right angle:
-
Handle glass with care: Special care must be taken with the edges of the glass – hardened glass can shatter into small pieces in the event of impact. Insert protective cushioning (e.g: cardboard box) under the edge of the glass.
Tools required
Assembly illustrations
(following the last language of the instructions) page 11
Circuit diagram
1 – 11 Numbering Spare parts list
Operation
Commissioning
Connect all connectors according to the cir-cuit diagram and then connect the
control unit (power unit) to the wall socket. On/off lights up on the display.
Press On/off to switch the control unit on. The heating elements start to
heat. The cabin temperature and the operating time are displayed. The time is
auto-matically activated for 60 minutes or to the last selected time. If you
press On/off again, all functions (heating elements, light and music) are
switched off.
- Settings can be made for 10 seconds (flashing display), then it switches to display mode.
Temperature settings
The desired temperature can be set with the Temperature +/- keys (30-70 °C).
When the temperature is reached, all heating elements are automatically
switched off. If the temperature drops 2 °C below the previously set
temperature, the heating elements are automatically switched on again. If the
cabin temperature exceeds 80 °C, “HH” flashes in the display. All functions
are automatically switched off. Wait until the temperature drops below 70 °C,
and restart the cabin with ON/OFF.
- The maximum temperature that can be reached in the cabin may be lower than the desired temperature. This depends on the temperature outside the cabin.
Time settings
The desired heating time from 5 to 60 min. can be set with the Time +/- button
(each press of the button = 1 minute). There is then a countdown of the
minutes and at “00” all functions are automatically switched off.
Light
Pressing the Light button switches on the reading light and the coloured
light. You can enter the setting mode by pressing and holding the “Light”
button for three seconds (“Lx” (x = 1-9) in the temperature display and “2n”
in the time display). The following settings are possible:
“Time +”: Reading light on/off
“Time -”: Coloured light on/off
“Temperature + / -”: Colour selection
L1 = white, L2 = pink, L3 = blue, L4 = sky blue, L5 = green, L6 = yellow,
L7 = red, L8 = rotate colours, L9 = slow change of colour
Music
By pressing the Music button you can switch between the FM radio, Bluetooth,
USB and external input AUX functions. Volume +/- can be used to control the
volume in the range of 1 to 30. Press Track to select the previous/next
track/radio station.
FM radio
Press the Music button until FM is displayed and then press and hold the Music
button for three seconds. The radio will automatically search for and store
sta-tions (stations from 87.5 MHz to 108.5 MHz). Press Track / to select the
previous or nextradio station.
Bluetooth
Press the Music button until BLU is displayed, in order to activate the
Bluetooth connection to your mobile phone. Turn on the Bluetooth search
function of the mo-bile phone and search for the “BT Sauna” Bluetooth device
(match time = 7 sec.). After successfully connecting with the phone, you can
play the music from the mobile phone.
USB
Press the Music button until USB is displayed. Music (MP3) is played from the
inserted USB stick.
AUX
Press the Music button until AU is displayed. The music from the connected
device plays.
Assembly illustrations
Guarantee card
Fill in this form and send it by e-mail to your dealer
- Invoice number: _____
- Date of invoice: __
- Name / telephone number/ email: __
- Item condition (unopened, recently opened or used): __
In the images below, identify (with a circle), the defective item. Include pictures of the defective item as an attachment, and send them by e-mail.
Spare parts
| Nr. | NAME | ORDERNUMBER |
|---|---|---|
| 1 | Control unit | Onni-IR-P |
| 2 | Control panel | Onni-IR-C |
| 3 | Radiator complete 400 W (77021040) | Onni-IR-400 |
| 4 | Radiator element 400 W (540*Ø10) | Onni-IR-400-ES |
| 5 | Heating element side 300W | Onni-IR-300-S |
| 6 | Heating element calves 200W (65x30mm) | Onni-IR-WP-200-65 |
| 7 | Heating element floor 200W | Onni-WP-200-B |
| 8 | Spot reading light 3W | Onni-IR-SP |
| 9 | Color light | Onni-IR-RGB |
| a | Speakers 2x5W | Onni-IR-LSP |
| b | Temperature sensor | Onni-IR-F |
sentiotec GmbH
Division of Harvia Group
Wartenburger Straße 31, A-4840 Vöcklabruck
T +43 (0) 7672/22 900-50
F -80
info@sentiotec.com
www.sentiotec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>