Norman N301488-1 AutoWand Shade Motorization Instruction Manual
- July 16, 2024
- NORMAN
Table of Contents
N301488-1
65101-50770-A
Installation Instructions
AutoWand Motorized
N301488-1 AutoWand Shade Motorization
- Please take a moment to review the following installation guide.
- Please leave shade in folded open position for ease of installation
- Be sure to keep all components and packaging until shade is fully installed
Recommended Tools—-
- Power drill and Drill bit
- Tape Measure
- Screwdriver
- Level
- Pencil
Fasteners needed for different mounting surfaces:
| Surface | Fastener |
|---|---|
| Wood | 1 1/2” Screw (Provided) |
| Drywall/Plaster | Wall Anchors, Expansion Bolts (Not Provided) |
| Metal | Sheet Metal Screws (Not Provided) |
Hardware Included
| Name | Picture |
|---|---|
| Outside Mount Male Bracket | |
| Inside Mount Male Bracket | |
| 1 1/2” Screw | |
| 2 1/2” Screw (when spacer block) | |
| 18mm Screw | |
| Hook for Wand | |
| Spacer Block | |
| 9/16” Screw |
To mark the brackets
Step 1: Position the shade inside or outside (depending on the version)
the window opening.
Make a mark along the end of the headrail on both sides on the mounting
surfaces.
Step 2: Mark the positions where you will install the brackets, 3.5” (89mm) in
from each side of the shade.
** Proper alignment of brackets will make installation easier.
A. Mounting the brackets inside a window frame
– When flush inside mount, allocate a min. distance of 1 3/8″(34mm) for
AutoWand Motorized, while 2” (SOmm) for AutoWand Motorized dual from the edge
of the wall to the center of the screw hole. – For semi-inside mount, it
should be at least 3/4”(19mm)} from the center of screw hole to the edge of
the wall.
-Use one 1 1/2” Screw to secure brackets.
B. Mounting the brackets outside a window frame
The combination of bracket and one spacer block will be used. Put the spacer
block at the back of the bracket as pictured below, and then attach the
combination with 2pcs 2.5″ screws.
Note: If additional spacer block is required, please install it as above
picture.
To mount the shade
Shade Installation is the same for both inside and outside mount applications
For AutoWand Motorized and AutoWand Motorized Dual, before installing the
shade into the mounting brackets, please locate the lock pin in the shade
bracket on the end plug side. Slide the pin downward into the end plug to
prevent the shade from falling.
Step 1: Align the female bracket on the shade to the male bracket.
Step 2: Slide the female bracket on the shade into the male bracket until
it snaps into place. If more than two brackets are used, it is recommended to
attach the center female bracket into the male bracket first, and then attach
the female bracket at each end.
Step 3: If the female brackets are a little off from the male bracket,
the position of the female brackets can be adjusted by moving left or right
8mm (5/16).
Note: To make the installation easily, please do the best to eliminate
the deviation of the placement of bracket, to make sure the male bracket is in
the middle of the female bracket.
To Install the Power Wand
A. Install the Hook
After the shade is well installed, please mark the position where you will
install the hook for the Power Wand. Please make sure the Power Wand can
connect to the motor after it is attached to the hook. Use one 18mm screw to
fix the hook.
B. Operate the Shade
First please attach the Power Wand to the hook, and connect the cable of power
and to the motor, and then the shade will turn on automatically.
To remove the shade
Step 1: Insert the screwdriver into the space between the female and male
bracket. Separate male bracket apart from the female bracket by revolving the
screwdriver as pictured below. tf more than two brackets are used, it is
recommended to separate the racket
at each end first, and then separate the one in the center.
Step 3: Gently pull the shade outward to remove the shade.
Recharge the Power Wand
If the motor beeps during the shade running, it means low voltage of the
motor. Charge the motor with 5V USB charger via the power wand.
When the motor is recharging, the indicator at the bottom of the power wand
will flash red, and it will change to green light when the motor is fully
charged.
Magnetic hold down (optional)
- The magnets are pre-installed on the back of shade at both bottom sides, 3/4” (20mm) to the side edge, and 9/16”(15mm) to the bottom edge.
- After the shade is installed, please fully lower the shade and mark the position for the magnet catch on the window frame to match the magnets on the shade, and fix it with one 9/16” screw. When the shade is lowered fully, it will be pulled at the magnet catch.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>