KEMPPI Zeta G200x Welding and Grinding Helmets Instruction Manual
- June 4, 2024
- KEMPPI
Table of Contents
Zeta G200 Welding and Grinding Helmets
Zeta G200
Zeta G200x
Introduction
Zeta G200 and G200x
The Zeta G200 and G200x grinding helmets are designed for grinding work,
surface finishing, and inspections. They are not designed for welding or
sandblasting. The Zeta G200 and G200x grinding helmets protect the wearer’s
eyes and face. The Zeta G200x model is also equipped with integrated LED work
lights.
About this manual
Please read these instructions for use carefully before using the device
for the first time. Please pay particular attention to the safety
instructions.
Disclaimer
While every effort has been made to ensure the accuracy and completeness of the information contained in this manual, Kemppi accepts no liability for errors or omissions. Kemppi reserves the right at all times to change the specifications of the product described without prior notice. The contents of this manual may not be copied, recorded, reproduced or transmitted without prior permission from Kemppi.
Security
Warning:
- It is strictly forbidden to use Kemppi personal protective equipment with parts or accessories other than those of the Kemppi brand. If you do not observe these safety regulations, this can lead to serious damage to your health.
- We recommend a service life of 5 years. The service life depends on various factors such as use, cleaning, storage, and maintenance. Check the helmet before each use. Replace worn or damaged parts.
- Use all setting features for optimal protection.
- Never use scratched or damaged visors.
- Those in contact with the wearer’s skin Materials could affect sensitive individuals and cause allergic reactions.
- Only operate this product in the temperature range from -5 to +55 °C.
- The product is not intended for use in potentially explosive atmospheres areas determined.
- The helmet does not protect against explosives or corrosive Liquids.
- The helmet only offered at room temperature (EN166 B) and only if all are fastened as specified Helmet components (see the description in the manual) Protection against high-speed particles.
- If a helmet is worn over goggles, can the impact of particles with high speed be transmitted and thus a danger for representing the wearer?
- If not all the markings of the various Protective equipment parts are equivalent, all protective equipment at the lowest protection level can be classified
parts
- Grinding mask
- Headband, Adjustable
- Sweatband, washable
- Open/close voltage adjustment
- Battery unit for LED work light (G200x model only)
- LED work lights (G200x model only)
- Distance slider (connect the headband with the helmet and set the distance between helmet and face on.)
- Viewing angle adjustment knob
Using the helmet functions
Commissioning
- Adjust the helmet to your head:
- Adjust the seat depth of the helmet using the upper ligaments a
- B. Adjust the distance between the helmet and Face with the slider on (b). Place sure that the helmet is comfortable as close as possible seated on the face and both sides are aligned the same.
- To tighten and secure the headgear, turn the knob on the back (a).
- Rotate the viewing angle setting to tilt the viewing angle up or down. (d)
- Adjust the voltage for opening/ Close in (e).
Using the work lights (G200x)
The Zeta G200x helmet is equipped with LED work lights. These are made from a
rechargeable lithium Ion battery pack powered on a neckband.
- To check the battery status, press the Battery test button on the battery unit.
- To charge, remove the battery pack from the helmet and charge the battery via the USB-C port with a charging cable (charging cable not included). included in delivery).
- Place the battery pack in the battery holder into the headband and connect the cable of the LED work light on.
- Use them to turn on and off OFF/AUTO/ON selector switches. Become in AUTO mode the lights in brightness (e.g. daylight) are switched off and vice versa accordingly switched on.
Caution : Never use damaged ones’ battery units. The battery unit of the LED light is not waterproof. Avoid extreme temperatures direct sunlight, humidity, sand, and dust. Keep the battery unit during the store in mind. If the battery unit when the Load becomes hot smokes or shows visible deformation perform
Replacement of spare parts
Removing the headgear
- Press and hold the distance slider
- Push in the headgear connector forward and away from the distance slider.
Attaching the headgear
- Place the headgear connector in front of the Distance slider
- Press the slider adjustment button while the headband connector is through the spacer Press slider
- Slide the headband connector into position so that the slider adjustment pin goes into one of the locking positions in the headband connector.
- Adjust the helmet to face distance
Replacing the grinding visor
- Replacing the grinding visor: loosen the helmet attachments. To do this, drag the Lock clips inward and pull out the grinding visor (a).
- Mount the grinding visor: Put the visor clips into the helmet mounts (b) and lock them by pressing up (c). Respect, think highly of Make sure that the lower fasteners also by default (d).
Maintenance
Inspect the helmet after each use. swap worn and damaged parts immediately.
Cleaning
- Clean the grinding visor with a mild detergent, lukewarm water and a soft one Cloth.
- Remove and wash the sweatband Requirement.
Wire feeder accessories
Store the Zeta helmet at temperatures between -20 to +50 °C and less than 80%
relative humidity. Store and transport the helmet and accessories in the
original packaging
|
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>