SPORTSATTACK SNAP ATTACK Football Machine Instruction Manual

SPORTSATTACK SNAP ATTACK Football Machine

INTRODUCTION

Thank you for purchasing this Sports Attack, LLC. equipment.
Your Snap Attack™ will be shipped in the right-hand spiral position.
Proper assembly, careful operation and consistent maintenance of this equipment will ensure that it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly set up the Snap Attack Football Machine, and to use, care for and maintain the Snap Attack in a manner which will ensure its optimum performance.

WARRANTY STATEMENT

What is most important to Sports Attack is that your machine meets your expectations of quality and performance. We stand behind the material and workmanship of our machines for five (5) years from the date or original purchase for institutional and residential use and one (1) year for commercial environments, with the following exceptions:

• Throwing Wheels are warranted for two (2) years;
• Electronic Controller is warranted for two (2) years; and,
• Throwing Wheel Motors are warranted for two (2) years.

This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not in effect if the machine has been misused, misapplied, improperly assembled, or modified without the express written permission of Sports Attack. In addition, this warranty does not apply to damage in transit, in any accident unrelated to the direct operation of the equipment, or by fire, flood or act of God.
If you encounter any issues during the warranty period, Sports Attack will quickly get your machine back in working order. If the warranty repair involves a replacement part, we will make sure you get both the part and easy instructions for replacement at no cost to you. If a service person is needed, Sports Attack will pay the pre-approved labor charge to get your machine back in working order.

EFFECTIVE IMMEDIATELY: Warranty components such as motors, etc. now require a picture of the component when submitting replacement request.
Please know that any problem can quickly be resolved with a phone call to our experienced, responsive customer service department at 800.717.4251. We are here to answer your questions and to make sure your machine provides you years
of service.

RETURNS

Sports Attack manufactures the highest quality sports training equipment in the world. If for any reason you are not satisfied, a machine can be returned within 30 days of receipt for any reason for a full refund less a 10% restocking fee. Cost of shipping the unit back to Sports Attack will also be the responsibility of the purchaser. Please note that the refund amount may be reduced by any non-cosmetic damage to the machine.
If you have any questions or concerns, please give our experienced, responsive customer service department a call at 800.717.4251.

SHIPPING DAMAGE CLAIMS PROCEDURE

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED

1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.

Sports Attack, LLC. cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the necessary documents to support your claim.

To register the Warranty, please go to our website: www.sportsattack.com/warranty
For repairs and service after the Warranty period, please call:
Customer Service Dept.
Ph 800.717.4251
Fx 775.345.2883

RETURNS

To return an item, please contact our Customer Service Department at 800.717.4251.
A 15% restocking fee will be charged for any items accepted for return. It is the customer’s responsibility to handle the repacking and shipment (as well as all associated fees) back to Sports Attack.
No returns will be accepted after 30 days of receiving this product.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Use a 115 volt single phase 3-wire grounded power source. Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire extension cord. Over 200 ft. from power source, consult a licensed electrician for required power cord size.

OPERATING SAFETY

CAUTION: Never reach down near moving throwing wheels for any reason! If it is necessary to reach into the throwing wheels, ALWAYS:

1. Turn speed dial to “0”.
2. Turn the power switch “OFF”.
3. Unplug Snap Attack™ from power source.
4. Wait until the throwing wheels have come to a complete stop before reaching hands or fingers anywhere near the throwing wheels.

CAUTION: Carefully check Snap Attack for completeness and condition before connecting to electrical power:
Carefully check the throwing wheels frequently for cleanliness, chips and cracks. Do not use the machine if the throwing wheels are damaged, or if chips or cracks appear in the wheels. (For damage within warranty period, see Warranty Statement, page 1.)
ALWAYS set the speed control to “0” before connecting the machine to power. Check that the speed control is at “0” before turning the throwing wheels “ON”.
Do not allow anyone to walk in front of the Snap Attack Football Machine if it is connected to electrical power.
CAUTION: DO NOT plug in or energize this equipment until all assembly instructions and operation instructions are read and followed.

BALL SELECTION

Balls must be official size and consistent in type to produce repeatability.
Never use wet or damp balls! Ball air pressure must be between 10-12 lbs.

ELECTRICAL SHOCK HAZARD

The Snap Attack must be connected to a properly grounded electrical receptacle.
Do not operate on wet ground.

CAUTION
PERSONAL INJURY HAZARD

Keep hands away from throwing wheels anytime the machine is connected to a power source.
Carefully check the Snap Attack for completeness and condition before connecting to electrical power.

EQUIPMENT ELECTRICAL DAMAGE

Keep hands away from throwing wheels anytime the machine is connected to a power source.
Carefully check the Snap Attack for completeness and condition before connecting to electrical power.

BALL REQUIREMENT

Do NOT use synthetic leather footballs. We recommend full grain leather.

COMPONENT VIEW

SET-UP & PREPARATION

Using the Snap Attack on the ground as a centering machine
The Snap Attack can be used in one of two modes. The first is when it is used on the ground to perform as a centering machine. The second is when it is used on its stand to perform as a quarterback when throwing passes or as a kicker or punter.
Setting machine up to perform as a centering machine

1. If machine is attached to stand:

   • Tip machine up and over onto feet (See Figure 1).
   • Unsocket the three legs and remove both knobs (See Figure 2) and store on same bolts.
   • Remove machine from stand.

2. Open rear leg support latch and insert rear leg support (See Figure 3).

3. Close latch over rear leg and tighten with wing nut (See Figure 4).

4. Tip machine back onto rear leg.

5. Point machine to desired direction.

6. Adjust angle by using your left hand to grab the passing handle and right hand to depress and adjust into 1 of 10 positions.

7. Turn machine on and turn Wheel speed control Knob to approximate speed.

8. Set ball carefully into Ball Cradle and feed ball into throwing wheels.
   IMPORTANT : For tightest spiral slide Ball Cradle gently, allowing wheels to capture & impel ball. Do not jam cradle and ball into machine.

9. Adjust elevation and wheel speed until exact spin is attained

SET-UP & PREPARATION

Using the Snap Attack on the stand to throw passes, punts and kicksoffs
IMPORTANT: Lock pin A must be removed (See Figure 1) and stored in adjacent hole to left. This will allow machine to pivot horizontally.
IMPORTANT: For maximum distance, balls must be properly inflated. (See chart at bottom of page 2).

SETTING MACHINE UP

1. Using knobs (See Figures 3) which are stored on bolts, attach throwing head to undercarriage (See Figure 2), tighten wing nuts B securely to undercarriage.
2. Insert 3 legs into sockets. (See Figure 2)
3. Using lifting handles (See Figure 1) tilt machine up onto all three tripod legs.
4. Remove lock pin A and store in adjacent hole to left (See Figure 4).
5. Loosen horizontal control handle D (See Figure 2 & 4).
6. Loosen pass and kick elevation handle E (See Figure 2).
7. Plug machine into power source. (110v)
8. Turn power switch “ON”.
9. Loosen wheel tilt handle E (See Figure 2) . Over time this wheel tilt handle G will have to be adjusted adjust loosen bolt until handle angle be changed to new proper position. Then tighten bolt securing handle in adjusted position.
10. Using wheel tilt angle handle G (See figure 2) push forward for end-over-end or pull back for passes and punts.
11. Dial wheel speed F to approximate speed.
12. Continue throwing test balls and adjusting speeds until desired distance and speed is achieved.

NOTE: Maximum post height should not exceed 34” with the stand on the ground. See page 11.

SHUTTING DOWN & TRANSPORTING

TURNING SNAP ATTACK “OFF”

1. Turn the power switch “OFF” and unplug Snap Attack from the power source.

TRANSPORTING WITH STAND

1. Be sure machine is turned “OFF” and wheels are not turning.
2. Unplug cord from extension cord, standard outlet or generator.
3. Frame lock pin A (See Figures 2 & 4) must be inserted in hole to right, locking head into position for transporting.
4. Using the elevation control, tilt the throwing heads up (to high position) and lock into place (See Figure 5). This will facilitate transporting.
5. Using handles C (See Figure 1) tip machine up and over onto lifting handle assembly feet See Figure 1). Unsocket two lower (front) legs, leaving upper (rear) leg in socketed position.
6. Lift rear leg and roll machine (See Figure 5).

PASSING, PUNTING & KICKOFF

The Snap Attack is able to simulate both right-hand and left-hand spins.
Two wheel tilt handles G (See Figure 1) are located underneath both motors, one on each side, and are used to change the angle of the wheels to provide either end-over-end or spiral ball delivery.
L- Left spiral pass, left handle is all the way forward away from operator, right handle is in the opposite position.
R- Right spiral pass, right handle is all the way forward away from operator, left handle is in the opposite position.
K- Lines indicate range for kick-off setting, depending on ball size and inflation, forward line provides furthest distance. Both handles must be in the same position
in the slider for an end-over-end kick.

FEEDING BALL INTO THROWING WHEEL (See Figure 6)

IMPORTANT: Be sure cradle is pulled all the way back. Use ball feed handle J (See Figure 2). Ball is positioned the same in cradle for any pass, punt or snap. See Figure 6).

CARE, CLEANING & MAINTENANCE LUBRICATION (once per season, or as

required)

1. Pass & Kick Elevation Control Handle E (See Figure 2) Apply fresh grease to threads.
2. Horizontal Swivel Lock
   • Completely remove the horizontal pivot control handle. Clean all old grease, dirt, etc. from the threads.
   • Wipe the threads with a very small amount of fresh grease.
   • Reinstall.

THROWING WHEEL MOTORS

Motors are sealed and require no lubrication. Check bolts for tightness once a season. Tighten bolts securely, but do not over-tighten. (See page 7).

CLEANING THE THROWING WHEELS

The throwing wheels must be kept clean to maintain accuracy. Clean the wheels periodically to control the build-up of grass and dirt.

1. Turn the power switch “OFF” and allow the wheels to come to a complete stop.
   Unplug Snap Attack from electric power.

2. Dampen a rag with soap and water. Turn the throwing wheel by hand and scrub the wheel until the build-up is removed. For very heavy build-up, a synthetic scouring pad, such as a Scotch-Brite® scouring pad, may be used sparingly.

EXAMINE THE MACHINE

Examine Snap Attack for condition and completeness before every use:

1. Throwing wheels must be tight on the motor shafts. Check that the four bolts holding the motor to the throwing head assembly are tight.
2. Wheel guard and ball cradle must be securely fastened.

COMPONENT REPLACEMENT

THROWING WHEEL REPLACEMENT

1. Turn the throwing wheels “OFF” and unplug the power cord. Remove 4 bolts holding the top wheel guard to the bottom wheel guard.

2. Hold the wheel so that it cannot move. Turn the keyway retaining bolt counter-clockwise using a box end wrench (See Figure 7).
   SUGGESTION: If the bolt is too tight, give the opposite end of the wrench a series of light taps with a hammer making sure the wrench remains on the bolt.

3. Remove the bolt and washers.

4. Work the wheel off of the motor shaft. Be sure to catch the key as it is freed from the keyway.

5. Ball throwing wheels are machine balanced. Small holes in the side of the wheel are applied at the factory and are normal. Reassemble in reverse order.

   • Install wheel to motor shaft with key slots aligned.
   • Be sure the key is in place, and inserted so that it is flush with the boss at the wheel center.
   • Be sure the Washer and Lock Washer are installed in the right order, and that the keyway retaining bolt is tightened.
   • Test the wheel by spinning it by hand and making sure that it spins freely without wobble before turning the unit “ON”.
   • Be sure the top wheel guard is properly and securely reinstalled.

MOTOR REPLACEMENT

1. Turn the power switch “OFF” and unplug the power cord.
2. Remove top wheel guard (See Page 9).
3. Remove the throwing wheel.
4. Remove bottom wheel guard.
5. Remove four screws holding the controller into the control box. Note the position of the motor wires on the controller, then disconnect the wire for the motor to be replaced.
6. Note the routing of the motor wires. Loosen wire clamps and pull wire away from machine.
7. To remove motor, remove the 2 – 1/4” x 3/4” coarse Allen flat socket cap screws using a 5/32” Allen wrench. Then remove the 2 – 5/16” x 1” coarse thread bolts using a 1/2” socket.
8. Reassemble in reverse order.

NOTE: Check bolts for tightness once a season. Tighten bolts securely, but be sure not to over-tighten.

CONTROLLER REPLACEMENT

1. Turn the power switch “OFF” and unplug the power cord.
2. Remove knob from the controller.
3.  Remove four screws holding controller faceplate into main casting. Note the position of the main power and motor wires on the controller, then disconnect the wires. (See Figure 8) for the two motor wires and the main power cord wires.

Loosen the nuts holding the speed control shaft (potentiometer) to the faceplate, then remove the controller.

Reassemble in reverse order.

Be sure wires are correctly reinstalled. Motor wire connectors are different sizes. Be sure they are installed on the correct size terminal.

EXPLODED VIEW – SNAP ATTACK™

Exploded View

1. Cane Tip
2. Leg
3. wivel Assy
4. Handle Horizontal Swivel Lock
5. Locking Pin Frame to Swivel
6. Undercarriage Assy
7. Handle, Elevation
8. 7a Bolt, Carriage
9. 7b 5/8” Nylon Nut
10. 8 Disc, Elevation
    • 8a bElevation Clutch
11. 9 Throwing Head Assy
    • 9a Snapping Tube Elevation Mount
12. Motor 110V
13. Motor 220V
14. Motor Mount Plate with Pin
15. Smile Plate
16. Throwing Wheel
17. Wheel Guard, Lower Left
18. Wheel Guard, Upper Left
19. Wheel Guard, Lower Right
20. Wheel Guard, Upper Right
21. Controller (110V/220V)
    21 Slide, Lower Cradle Slide
    22 Slide, Upper Cradle Slide
    23 Ball Cradle
    27 Throwing Head to Yoke Knob
    39 Knobb, Motor Lock
    40 Travel Wheel
    37 Universal Cart Clamp

PARTS LIST

EM PART NO. DESCRIPTION QTY PER

• 1 280-1003 Cane Tip 1
• 2 532-0007 Leg 1
• 3 531-1046 Swivel Assy 1
• 4 533-2016 Handle Horizontal Swivel Lock 1
• 5 340-2009 Locking Pin Frame to Swivel 1
• 6 533-2014 Undercarriage Assy 1
• 7 533-2026 Handle, Elevation 1
• 7A 410-0040 Bolt, Carriage 1
• 7B 430-1041 5/8” Nylon Nut 1
• 8 533-2027 Disc, Elevation 1
• 8A 340-2019 Elevation Clutch 1
• 9 510-0004 Throwing Head Assy 1
• 9A 533-2012 Snapping Tube Elevation Mount 1
• 10 530-1012 Motor 110V 2
• 11 530-1013 Motor 220V 2
• 12 531-1029 Motor Mount Plate with Pin 2
• 13 271-0008 Smile Plate 2
• 14 531-0009 Throwing Wheel 2
• 15 533-2022 Wheel Guard, Lower Left 1
• 16 533-2023 Wheel Guard, Upper Left 1
• 17 533-2021 Wheel Guard, Lower Right 1
• 18 533-2024 Wheel Guard, Upper Right 1
• 19 530-0005 Controller (110V/220V) – Specify 1
• 20 533-2016 Handle Lifting 2
• 21 350-0006 Slide, Lower Cradle Slide 1
• 22 350-0007 Slide, Upper Cradle Slide 1
• 23 520-0010 Ball Cradle 1
• 24 533-2002 Spring Lever Snap Elevation Control 1
• 25 290-0005 Foot 1
• 26 533-2000 Snapping Tube, Lower Elevation 1
• 27 280-2000 Throwing Head to Yoke Knob 1
• 28 533-2006 Snapping Elevation Extension Tube 1
• 29 290-0004 Snapping Elevation Control Handle 1
• 39 280-2001 Knobb, Motor Lock 2
• 40 281-0001 Travel Wheel 2

ATTACHING OPTIONAL CART CLAMP

Designed to fit 2½” to 4” round or square post

1. Insert clamp bolt through top plate. Loosely attach washer and nut. Finger tighten.
2. Put 3 bolts through sides of clamps. Slide unit over post, then attach fourth bolt.
3. Center top plate to post. Begin tightening 4 clamps to top plate, but do not completely tighten.
4. Begin to secure the 4 side bolts. Completely tighten.
5. Completely tighten 4 clamp nuts to top plate.

CART CLAMP KIT
_It_em __Q_ty _

• Clamp 4
• Top Plate 1
• ½-13×3 ½ Bolts 4
• ½-13 Nylon Lock Nuts 8
• ½ SAE Plain Washers 4

Tools needed are either a ¾ wrench or socket wrench.

Note: Maximum post height should not exceed 34” with the stand on the ground. When attaching the option cart clamp, slide unit over post and dry fit to ensure that maximum post height from ground to top of the post does not exceed 34”. If your post height exceeds 34”, you should cut your post so that it complies with this measurement.

SNAP ATTACK™ FOOTBALL MACHINE
Sports Attack, LLC. | 800.717.4251 | www.sportsattack.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>