SINAOPUS DSV808 Diyuto Cordless Vacuum Cleaner User Manual

DSV808 Use Manual

Safety Instructions

In order to avoid electric shock, fire and other accidental injuries caused by improper use, please read the instruction manual carefully before use.
This product may not be used by physically, sensually or intellectually disabled persons and the elderly, children.
Children are prohibited from operating the product or using it as a toy, and close attention is required when using the product near children; children are prohibited from cleaning or maintaining the product without a guardian.
Prohibit the use of the product outdoors or on wet surfaces, indoor use on early surfaces only, do not touch the plug or any part of the product with wet hands, please avoid the product from getting wet or water.
To prevent fire, explosion or injury, check the battery and charger for damage before use, and do not use the vacuum cleaner with a damaged battery or charger.
Do not use the product to absorb flammable or explosive liquids such as water, petrol, etc. Inhalation of toxic solutions is prohibited.
Do not use the vacuum cleaner to clean lime, cement, carbon powder, etc. Do not inhale smoking or burning materials.
Only use the original charger, please do not use the unofficial adapter, otherwise it will cause damage to the product, please unplug the charger after fully charged, so as not to overcharge to shorten the battery life and reduce the performance; do not disassemble and replace the battery by yourself; do not place the battery in the fire, so as not to cause an explosion.
Do not place the vacuum cleaner against unstable surfaces such as chairs, dining tables, etc. to prevent damage to the product or injury to the user after falling; when the vacuum cleaner is damaged due to falling, injury or other abnormalities, please contact the official authorized maintenance, do not disassemble it by yourself.
Please do not use this product directly on the human body on clothes, fingers, head hair vacuuming operation; please avoid the machine rain, water This product is only suitable for use in a home environment.

Product Introduction

List of accessories

(with screws3, expansion tube3)

Part Name

1. Motorised floor brush
2. Motorised floor brush release button
3. Telescopic tube assembly
4. Telescopic tube release button
5. Air outlet
6. Dust cup release button
7. Speed regulation switch
8. Display screen
9. Power switch
10. Battery pack assembly
11. Charging hole
12. Battery pack release button
13. Dust cup
14. Dust cup bottom cover
15. Dust pouring button
16. Telescopic tube length adjust but- ton

Screen display:

1. Ground brush blocking icon: the red-light flashes after the roller brush is blocked and stopped, the ground brush stops working and the main motor does not stop.
2. Gear icon, manual mode 1-6 gears light blue.
3. LOGO white light
4. The wind blade icon rotates from slow to fast according to the gear level.
5. Motor plug protection indicator flashes red,
6. Power indicator

Product Installation

Mainframe Installation

1. Battery pack installation and removal Removal: push down the battery pack latch and pull out the battery pack assembly backwards Installation: Push forward into the slot and latch into the slot to lock it in place.
2. Dust cup installation and removal
   Dust cup installation: 2. The dust cup connector pin is inserted into the slot of the body and the latch locks securely.Dust cup installation: 1. Dust cup card foot inserted into the rack front cover slot
   Note: Dust cup feet must be inserted into the slot in order to install and use.

Accessory Installation

Insert the aluminium tube latch into the main unit suction port locking

Insert the floor brush latch into the aluminium tube opening for lockingInsert the sofa suction into the main unit suction port and lock it in place.

Press the brush head latch, slide the brush head back and forth, according to the use of the environment can be adjusted to the bristle and flat suction two working conditions.
Insert the flat suction into the suction port of the main body and lock it, so that it can be used in the narrow opening.

Hanger Installation

The location of the hanger should be chosen in a cool and dry place with power supply nearby, and make sure that there are no facilities such as electric wires or pipes directly behind the installation area.

1. According to the length of the whole machine (host + aluminum tube assembly + floor brush), choose the right height and circle the three screw hole positions according to the drawing.
2. Use the power tool with 7mm drill bit to make holes according to the screw hole positions, and place the expansion tube inside the drilled holes.
3. In the hangers with three screws fixed. Plug the expansion tube into the hole and fix the wall hanging to the wall with 3 screws.

Storage and Charging

1. Slide the main unit into the slot of the rack from the middle position.
2. Snap the flat suction and sofa suction from the bottom into the bracket slot. The main unit is placed in the slot of the rack and can be charged directly by plugging in the charger.

Product Use

1. Press the switch on button, the machine defaults to low gear mode.
2. Gear adjustment, turn the knob clockwise or counterclockwise to adjust the gear, 6 consecutive gears to change the suction power.

Maintenance

caveat

1. Be sure to use original parts, otherwise the warranty may not be available.
2. Please charge the new product for 5 hours for the first two uses. Purpose: to fully activate the internal activity of the battery.
3. After the battery pack voltage drops, the charging and discharging indicator light and the battery pack indicator light on the front of the power switch flash at the same time, indicating that the battery is low and needs to be recharged.
4. When not in use for a long time, please fully charge the vacuum cleaner and then unplug the power adapter and place it in a cool and dry place.
   Charge the battery at least once every 3 months to avoid over-discharge.

Clean up the mainframe
Wipe the main unit with a soft, dry cloth.
Cleaning dust cups, filters and cyclone assemblies

1. Press the dust dumping button to open the bottom lid of the dust cup and dump the dust into the dust cup.
2. Hold the end of the steel mesh frame and rotate it clockwise to the stop position, take out the steel mesh frame, rinse it with clean water and dry it before putting it on.Hold the end of the steel mesh frame and rotate it clockwise to the stopping position, take out the steel mesh frame, rinse it with clean water and dry it before putting it on.

Hold the motor assembly and turn it anti-clockwise to the stop position.
Wipe the dust cup with a wrung out damp rag (the dust cup contains electrical parts, do not wash it directly with water).

Roller Brush Pickup and Placement

Basic parameters

Hosts

Product Model| DSV808| Charging Voltage| 31V
Rating| 380W| Rated Voltage| 25.9V
Charge Time| 4.5-5.5h| Battery Capacity| 2200mAH
Noise| ≤76dB| Dust Collection| Approx.0.8L
Running Time| Approx. 12 minutes for high end, 40 minutes for low end

Troubleshooting

charge the product before use.
Automatic protection triggered by high
temperatures due to clogging.| Clean the dust extraction port or the air intake
filter and restart it after it has cooled down.
Reduced machine suction| The cup is too full.| Cleaning out the dust cups
Machine suction port clogged| Clear the suction port.
Clogged filters| Cleaning filters
Battery status indicator does
not light up when charging| The main unit is not connected to the
adapter socket.| Check that the power adapter is plugged in
The battery is full and the battery goes to
sleep.| serviceable
non-charging| Battery temperature too high or too low| Please wait until the battery temperature returns to normal before charging
The charger power finger light is not lit.| 1.Charger is not plugged in
2.The socket is not powered, replace the socket
3.Charger failure, replace the new charger
Discharge
mode| plug a hole| Battery pack indicator and display block- ing indicator flash slowly 10 times and then go out| Clean up the blockage at the suction port, clean up the dust cup garbage, and restart the host to restore normal operation
Ground
Brush Plug-
ging| After the ground brush is blocked, the ground brush indicator flashes 3 times slowly, the ground brush stops working, and the ground brush blocking indicator of the display screen lights up for 30s and goes out.| Within 3 times of slow flashing of the ground brush indicator, the ground brush is released from blocking, then continue to work normally, after 3 times of the ground brush is still blocked, then stop working, the ground brush blocking indicator is on.
Low Battery
Alarm| Battery pack indicator slow flash, display power indicator 1 red slow flash 30 times off| Trigger by pressing the switch again after discharging
Ground
Brush Short| The battery pack indicator flashes slowly 30 times off, the display power indicator 1 red and indicator 1-4 green alternately flashes 30 times off.| Replace with a new floor brush
charging mode| Using the
wrong
charger| Battery pack indicator blinks fast, battery indicator 1.4 green blinks fast, display logo light is always on.| Charger unplugged to deactivate blinking status; indicator light off

Warning:

1. Before the machine is scrapped, the battery pack should be removed
2. When you need to remove the battery pack, the machine should be in a power-off state.
3. The battery pack contains lithium which is harmful to the environment, in order to protect the environment, the discarded battery packs should be sorted and recycled, and should be disposed of safely instead of being thrown into the rubbish bin
4. In order to avoid and prevent the danger of suffocation, all the bags of this machine should be kept away from babies and children.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>