TAKAYA TR3XM-C106-A3540 RFID Reader and Writer Module User Manual

TAKAYA TR3XM-C106-A3540 RFID Reader and Writer Module

Specifications:

• Product Name: TR3XM-C106-A3540 RFID READER/WRITER module
• Regulatory Compliance: FCC, ISED, Japan Radio Law
• Antenna Type: PCB

Product Usage Instructions

• Regulatory Compliance:
  The TR3XM-C106-A3540 RFID READER/WRITER module complies with BFCC, ISED, and Japan Radio Law regulations. It is important to adhere to these regulations for proper usage.

• RF Exposure Compliance:
  For FCC compliance, ensure a minimum distance of 20cm between the radiator of the device and your body during operation. Do not co-locate the transmitter with any other antenna or transmitter.

• End Device Labelling:
  If the IC identification number is not visible when the module is installed inside another device, an exterior label must be displayed on the device referring to the enclosed module.

• Japan Radio Law Compliance:
  This equipment conforms to the standards set by Japan Radio Law for inductive reading/writing communications equipment.

FAQ :

• Q: What should I do if I encounter interference while using the RFID module?
  A: Ensure that there is a minimum distance of 20cm between the radiator of the device and your body. Additionally, check for any nearby interfering devices and try to operate the module in a different location if interference persists.

User’s Manual
TR3XM-C106-A3540

Introduction

• Thank you for purchasing a TR3XM-C106-A3540 RFID READER/WRITER module.
• Be sure to read this manual before using the product.
• After reading it, store the manual in a convenient place for future reference.

Regulations and Standards

• FCC(※1)(※2)
• This product is conformed to the FCC standards.
• FCC Rules (Federal Communications Commission)
• This product complies with Part 15 Subpart C of the FCC Rules.
• FCC ID: MK4C106-A3540

FCC NOTICE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• RF Exposure compliance statement
• This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• Antenna Type: PCB
• The following sentence must be displayed on the outside of the device in which the transmitter module is installed: “Contains FCC ID: MK4C106-A3540”
• ISED

ISED ID : 31742-C106A3540
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is  subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radiation Exposure statement

• This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
• End Device Labelling
• Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 31742-C106A3540” any similar wording that expresses the same meaning may be used.
• Japan Radio Law
• Equipment using high frequencies: Inductive Reading/Writing Communications Equipment
• Conforming standards: Inductive Reading/Writing Communications Equipment.
• Standard: ARIB STD-T82
• 1
  This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
  Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.
  Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in §15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following:

For Class B
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

For Class A
Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

If Host manufacturer desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by Takaya, or host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.

Tags

• This product can communicate the standard tags of ISO/IEC15693, ISO/IEC18000-3(Mode1), ISO/IEC14443 TypeA, ISO/IEC14443 TypeB and ISO/IEC18092(212kbps, Passive
• Mode).
• TR3XM-C106-A3540
• Security function is not checked
• TR3XM-C106-A4247-MFC
• Security function is not checked
• TR3XM-C106-A4247-ILT

Security function is not checked

• RoHS is support
  Restriction of Hazardous Substances

• Waste
  Dispose of the Products as industrial waste.

Safety Precautions

The following symbols are used in this manual to indicate precautions that must be observed to ensure safe use of this product. The precautions provided here contain important safety information. Be sure to observe these precautions.

The following signal words are used in this manual.

• WARNING Failure to comply with a WARNING may result in serious injury or death.
• CAUTION Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved.

WARNING

Be sure to observe the following precautions to ensure safe use of the Products.

• Decomposition of this product and cable, repair, remodeling, please strictly prohibited. There is the possibility of fire or electric shock injuries.
• This product is using the RFID reader/writer radio equipment. Therefore, depending on where the applications you use may affect medical equipment. To minimize the impact of medical equipment for use, please observe the following countermeasure. The Japan Automatic Identification Systems Association
  (JAISA) guidelines are as follows: RFID antennas from implanted cardiac pacemakers or other medical devices please 22cm apart. We recommend that you paste “RFID sticker” at equipment.

CAUTION

Be sure to observe the following precautions to ensure safe use of the Products.

1. Do not use the Products in sunlight.
2. Do not use the Products in environment of spray of water, oil or chemicals.
3. Do not use the Products in environments with flammable, explosive, or corrosive gasses.
4. Do not use the Products in environment of hot humid.
5. Do not use the Products in environment of vibration or shock.
6. Do not use the Products in environment of condensation.
7. Do not use the Products in environment of around the metal is covered.
8. Do not use the Products in environment of high temperature.
9.  Do not use the Products in environment that has a device that generates magnetic field and shock voltage.
10. Do not use the Products in unstable place.
11. If there is failure, discontinue use immediately, please contact us or the distributor.

Installation

1. Turn off the power before installation or removing.
2. The following effects may not work correctly.
   • Near 13.56MHz radio device
   • Near speakers , Inverter, motor and Plasma Display
3. The communication range may vary due to environment and conditions.

Product Overview

Features

• This product uses the 13.56MHz frequency. This product is the electromagnetic induction type non-contact IC can read and write RFID tag data.
• This Product is designed to be embedded and integrated within OEM devices and finished products such as label printers, cashless payment terminals or any other device that can benefit from integrated RFID capabilities.
• Conform to international standards
• ISO/IEC15693 and ISO/IEC18000-3(Mode1), ISO/IEC14443 TypeA, ISO/IEC14443 TypeB, ISO/IEC18092(212kbps, Passive Mode), and ISO/IEC18000-3(Mode3) is supports.

Software

• TR3-series common communication protocol
• Software Development Kit

Useful

• Continuous inventory mode
• UID of the tag automatically sends Host Device.
• RDLoop mode
• UID or User Data of the tag automatically sends Host Device.
•  For more information, please refer to the TR3-PROTOCOL manual.

Environmentally

• EU RoHS(2002/95/EC) Support.
• And 10 substances prohibited by (EU) 2015/863 are below the standard value.

Names of Parts and Functions

TR3XM-C106-A3540

status.
②| Terminal block| Terminal block connecting to host device or interface board.
③| Serial number label| The serial number will be an 8-digit serial number.

④| Inspected seal| Showing this RW module has been inspected.
⑤| Shield case| Preventing RF circuit from touching.
⑥| FCC Label| Showing FCC ID.
⑦| Screw holes| M2 holes.

Setting and connection

This RFID READER/WRITER product is to be professionally installed by authorized, qualified and service-trained installation personnel only.

1. Setting

2. installation
   Please prepare four M2-screws (any length) and install READER/WRITER module.

3. Connection
   This product is used connecting to host device.
   You can connect directly or using our interface board products.

4. Direct connection to the Host Device Interface
   Directly connecting to host device. Please prepare harness to connect .

5. In case of the connection with Interface Board TR3-IF-1C

Connect configuration

• Ready made goods
• Our RS-232C cross cable
• (model name：CB-232C-2)

Connection(TR3-IF-1C + TR3XM-C106-A3540)

In case of the connection with Interface Board TR3-IF-N4

Connect configuration

• Ready made goods
• When connecting Via hub

LAN cross cable| 1| –|

• Ready made goods
• When connecting directly

Connection

Via hub

Connecting directly

In case of the connection with Interface Board TR3-IF-U1A
Connect configuration

name：CB-USB-1)

Connection

Specifications

TR3XM-C106-A3540

• Standard number: ARIB STD-T82
• Standard name:
• Inductive read / write communication equipment (Wireless card system, etc.)
• Model designation number:
• FC-23003
• (model name: TR3XM-C106-A3540)

FCC (※2)(※3)| FCC Part15 Subpart C FCC ID: MK4C106-A3540
ISED| ISED ID: 31742-C106A3540
RoHS|

• Compliant with the EU RoHS (2002/95/EC)
• However, the 10 substances prohibited by (EU) 2015/863 are below the standard value.

1. This product incorporates a reader/writer module that has been certified by the type of designation stipulated by the Radio Law of Japan. Therefore, it is not necessary to apply for permission to install high-frequency equipment in Japan. However, please note that if you use it in a combination of equipment configurations that we do not approve, or if you modify it to emit illegal radio waves, it will be a violation of the Radio Law and you will be punished.
2. This product is for domestic use only, and we do not provide maintenance service or technical support overseas.
3. FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Regarding registered trademarks >

Proprietary nouns such as company names and product names described in this manual are trademarks or registered trademarks of each company.
The ICODE SLI series is a trademark or registered trademark of NXP Semiconductors.

1. This product incorporates a reader/writer module that has been certified by the type designation stipulated by the Radio Law of Japan. Therefore, it is not necessary to apply for permission to install high-frequency equipment in Japan. However, please note that if you use it in a combination of equipment configurations that we do not approve, or if you modify it to emit illegal radio waves, it will be a violation of the Radio Law and you will be punished.
2. This product is for domestic use only, and we do not provide maintenance service or technical support overseas.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

This product is mainly made from electronic components and semiconductors.
Therefore, the long-term stable operation is expected. However, the defects as shown below are expected depending on environment and condition.

• Deterioration of elements resulted from overvoltage or overcurrent
• Deterioration of elements resulted from long-term damage in high temperature
• Deterioration of insulation and poor contact resulted from humidity or dust
• Corrosion of elements or poor contact resulted from Corrosive gas

To use this product in best condition, you are recommended to check regularly.

Surroundings

| Temperature| Surrounding temperature| 0～55℃
Humidity| Surrounding humidity| 30～85%RH
Dust| Dust| None
Corrosive gas| Corrosion| None
Power supply voltage| Input voltage| Voltage| When in 5.0V：DC+5.0V±10% When in 3.3V：DC+3.3V±10%
Voltage fluctuation| Radical fluctuation

Attachment

| Main body| Screw looseness| Not loose
Connector attachment| Locked or screw tightening
Cable| Is there sign of cut?| None
Power-on| Function| Function check| Normal

Revision History

• [URL]
  • https://www.takaya.co.jp/
• [Mail]
  • rfid@takaya.co.jp

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>