ASUS XD4S AX1800 Dual Band WiFi Router User Guide
- June 10, 2024
- Asus
Table of Contents
Quick Start Guide
ASUS ZenWiFi XD4S
AX1800 Dual Band WiFi Router Model: XD4S
Hardware Explanations
- Plug the adapter into the DCIN port.
- The power LED will light up when your hardware is ready.
XD4S Overview
-
WAN/LAN port
Connect your modem to this port with a network cable. -
LAN port
Connect your PC to a LAN port with a network cable.
Specifications:
DC Power adapter | DC Output: +12V with max 1.5A current |
---|---|
Operating Temperature | 0-40°C |
Operating Humidity | 50-90% |
Before Setup
Preparing to set up an AiMesh WiFi system
- Find three ZenWiFi XD4S, and power them on.
- Use a network cable to connect your modem to the WAN port of one XD4S. This ZenWiFi XD4S will be the AiMesh router, and the other two ZenWiFi XD4S will be the AiMesh nodes.
- The LED turns solid blue to indicate that ZenWiFi XD4S is ready for setup.
ASUS Router App
Download free ASUS Router APP to set up and manage your router(s).
|
---|---
https://play.google.com/store/apps/details?id=com.asus.aihome&hl=en|
http://itunes.apple.com/app/asus-router/id1033794044
AiMesh Setup Steps
-
Prepare
Place your AiMesh router and nodes in the same room and at least 1 meter apart during the setup process. -
AiMesh node
Keep your AiMesh nodes powered on and standby for AiMesh system settings. -
Launching ASUS Router APP
Launch ASUS Router APP, and then follow the on-screen instructions to finish the AiMesh setup.
Troubleshooting
If your AiMesh router cannot find any AiMesh nodes nearby or synchronization
fails, please check the following and try again.
a Move your AiMesh nodes closer to the AiMesh router ideally. Ensure that it
is within 3 meters.
b Your AiMesh nodes are powered on.
Relocation THE BEST PERFORMANCE
Locate the AiMesh router and node at the best place.
Solid blue:
Your ZenWiFi XD4S is ready for setup.
Solid white:
Your ZenWiFi XD4S is online and works well.
Solid yellow:
The signal between your ZenWiFi XD4S router and the node is weak.
Solid red:
Your ZenWiFi XD4S router has no Internet connection. / Your node is
disconnected from the router.
Wall-mount the ZenWiFi XD4S
IMPORTANT!
You can either install it with the ASUS logo facing up or down, depending on
the placement of your modem. .
DO NOT install this equipment on the ceiling or mount it higher than 2 meters.
NOTE: It is recommended to use the attached anchor and screws.
FAQ FREQUENTLY ASKED QUESTIONS
Does the AiMesh router support Access Point mode?
– Yes. You can choose to set the AiMesh router as router mode or access point mode. Please go to web GUI (http://router.asus.com), and go to the page Administration > Operation Mode.
Could I setup wired connection between AiMesh routers (Ethernet backhaul)?
– Yes. AiMesh system supports both wireless and wired connection between
AiMesh router and node to maximize throughput and stability. AiMesh analyzes
the wireless signal strength for each frequency band available, and then
determines automatically whether a wireless or wired connection is best to
serve as the inter-router connection backbone.
1 Follow the setup steps to establish a connection between the AiMesh router
and node via WiFi first.
2 Place the node in the ideal locations for best coverage. Run an Ethernet
cable from the LAN port of the AiMesh router to the WAN port of AiMesh node.
3 AiMesh system will auto-select the best path for data transmission, whether wired or wireless.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions
for you to be able to responsibly recycle our products, batteries, other
components, as well as the packaging materials. Please go to
http://csr.asus.com/english/Takeback.htm for the detailed recycling
information in different regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and
Restriction of Chemicals) regulatory framework, we published the chemical
substances in our products at ASUS REACH website at
http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC exposure compliance requirement,
please follow operation instruction as documented in this manual.
WARNING! This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 51 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.
Safety Notices
- Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).
- Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
- DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
- DO NOT place or drop objects on top and do not shove any foreign objects into the product.
- DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
- DO NOT cover the vents on the product to prevent the system from getting overheated.
- DO NOT use damaged power cords, accessories, or other peripherals.
- If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
- To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
- DO NOT mount this equipment higher than 2 meters.
This device is restricted for indoor use only. Manufacturer| ASUSTeK
Computer Inc.
Tel: +886-2-2894-3447
Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan
---|---
Authorised
representative in
Europe| ASUS Computer GmbH
Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY
Authorised
distributors in
Turkey| BOGAZICI BILGISAYAR TICARET VE SANAYI A.S.
Tel./FAX No.: +90 212 331 10 00 / +90 212 332 28 90
Address: ESENTEPE MAH. BUYUKDERE CAD. ERCAN HAN B BLOK NO.121 SISLI, ISTANBUL
34394
CIZGI Elektronik San. Tic. Ltd. Sti.
Tel./FAX No.: +90 212 356 70 70 / +90 212 356 70 69
Address: GURSEL MAH. AKMAN SK.47B 1 KAGITHANE/ISTANBUL
KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.
Tel. No.: +90 216 5288888
Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL
ENDEKS BİLİŞİM SAN VE DIŞ TİC LTD ŞTİ
Tel./FAX No.: +90 216 523 35 70 / +90 216 523 35 71
Address: NECIP FAZIL BULVARI, KEYAP CARSI SITESI, G1 BLOK, NO:115 Y.DUDULLU,
UMRANIYE, ISTANBUL
PENTA TEKNOLOJI URUNLERI DAGITIM TICARET A.S
Tel./FAX No.: +90 216 528 0000
Address: ORGANIZE SANAYI BOLGESI NATO YOLU 4.CADDE NO:1 UMRANIYE, ISTANBUL
34775
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>